User`s manual
PART LIST--Model No. 831.299470
R1000A
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key Key Key
No. Q_. Description No. Q_. Description No. Q_. Description
1 1 Motor Belt 48 1
2 1 Pulley/Flywheel/Fan 49 2
3 4 Motor Nut 50 1
4* 1 Motor/pulley/ 51 1
Flywheel/Fan 52 1
5 1 Incline Motor Bolt 53 4
6** 1 iFIT.com Video 54 4
7 1 Incline Motor 55 1
8 1 Stop Bracket 56 1
9" 1 Latch Assembly 57 1
10"* 1 HandWeight Set 58 1
11 1 Rear Foot Spacer 59 2
12 1 Frame 60 7
13 2 Interface Bracket 61 1
14 1 Incline Motor Pivot Bolt 62 5
15 8 Incline Motor Nut 63 1
16 8 Hood Screw/Guide 64 1
Screw 65 2
17 4 Plastic Stand-off 66 1
18 2 Hood Bracket (short) 67 1
19 1 Hood Bracket (long) 68 4
20 2 Warning Decal 69** 1
21 1 Reed Switch " 70 1
22 1 Reed Switch Clip 71 1
23 1 Motor/Contreller Wire 72 5
24 1 Controller 73 1
25 1 Electronics Bracket 74 1
26 1 Cimuit Breaker 75 2
27 1 Power Cord 76 14
28 1 Power Cord Grommet 77 1
29 1 On/Off Switch 78 1
30 18 Hood Bracket Screw/ 79 4
Incline Shield Screw 80 1
31 1 Incline Base 81 4
32 2 " Frame Pivot Bolt 82 1
33 2 Frame Pivot Spacer 83 2
34 1 Updght Wire Harness 84 1
35 1 Front Roller Adj, Bolt 85 2
36 3 Roller Adj. Washer 86 2
37 2 Motor Tension Nut/ 87 1
Front Roller Nut 88 t
38 4 Motor Bolt 89 12
39 6 Cap Screw 90 1
40 1 Left Foot Rail Cap 91 1
41 2 Foot Rail 92 1
42 1 Front Roller/Pulley 93 1
43 1 Magnet 94 1
44 2 Platform Screw (mid) 95 2
46 2 Isolator 96 1
46 10 Isolator Screw 97 4
47 15 Plastic Fastener 98 1
Foam Grip (Right) 99 1 Upright Grommet
Belt Guide 100 1 Allen Wrench
Book Holder 101 19 Screw
Front Belly Pan 102 1 25" Wire Harness
Power Supply 103 2 Extension Leg
Cable Tie Clamp !04 2 Base Endcap
Cable Tie 105 1 Shock
Walking Belt 106 1 Choke
Latch Spacer 107 2 Pulse Bar Bolt
Rear Roller 108 2 Pulse Bar Washer
Belly Pan Spacer 109 1 Pulse Bar
Rear Foot 110 1 Foam Grip (Left)
Rear Foot Screw 111 2 Tdm Guard
Ground Wire 112 1 Shield
Ground Wire Screw 113 2 Static Decal
Belly Pan 114" 2 Extension Leg
Rear Endcap Assembly
Rear Roller Adj. Bolt 115 2 Incline Pivot Nut
Motor 116 1 Console Base Bottom
Latch Decal 117 2 Updght Endcap
Platform Screw 118"* 1 Chest Pulse Sensor
IFIT.com Module 119 1 Bracket Grommet
Latch Catch 120 1 Rubber Ring
Walking Platform 121 2 Base Pad
8" Cable Tie # 1 8" White Wire, 2F
Jack # 1 4" White Wire, M/F
Motor Tension Bolt # 1 8" Blue Wire, 2F
Foot Rail Insert # 1 4" Black Wire, 2F
Small Screw # 1 4" Green Wire, F/Ring
console # 1 8" Green Wire, 2 Ring
Ground Washer # 1 7" Green Wire, M/Ring
Long Screw # 1 4" Red Wire, M/F
10' iFIT.oom Wire # 1 User's Manual
Motor Star Washer
Updght # These parts are not illustrated
Incline Base Pivot Bolt * Includes all parts shown in the
IFIT.com CD box
Handrail Extension
Wheel Bolt
Console Base
Motor Tension Washer
lf2" Screw
Key/Clip
Incline Motor Plate
Right Foot Rail Cap
Motor Tension Bushing
Motor Hood
Front Wheel
Incline Motor Shield
Thick Base Pad
12" Audio Wire
**These parts are Optional. For Infor-
mation about the iFIT.com module,
iFIT.oom CD's, or iFIT.com video-
cassettes, see your local SEARS
dealer or call toll-free 1-800-884-
0620. For information about the
optional hand weight set or chest
pulse sensor, see page 19.
27