Model No. PETL41307.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, please contact us at the numbers or addresses listed below: Call: 08457 089 009 Outside UK: 0 (44) 113 3877133 Fax: 0 (44) 113 3877125 E-mail: csuk@iconeurope.com Write: ICON Health & Fitness, Ltd.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. cuit. No other appliance should be on the same circuit. When replacing the fuse, an ASTA approved BS1362 type should be fitted to the fuse carrier. A 13 amp fuse should be used. 1.
20. Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on page 21.) You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill. 24. DANGER: Always unplug the power cord immediately after use, before cleaning the treadmill, and before performing the maintenance and adjustment procedures described in this manual.
BEFORE YOU BEGIN Thank you for selecting the revolutionary PROFORM® PF 5.2 treadmill. The PF 5.2 treadmill offers an impressive array of features designed to make your workouts at home more enjoyable and effective. And when you’re not exercising, the unique PF 5.2 treadmill can be folded up, requiring less than half the floor space of other treadmills. ing this manual, please see the front cover of this manual. To help us assist you, note the product model number and serial number before contacting us.
ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance.
2. With the help of a second person, carefully tip the treadmill onto its left side. Partially fold the Frame (56) so that the treadmill is more stable; do not fully fold the Frame yet. 2 38 Hole 83 Cut the tie securing the Upright Wire (38) to the Base (83). Locate the tie in the indicated hole in the Base, and use the tie to pull the Upright Wire out of the hole. 81 56 2 Attach a Base Pad (81) to the Base (83) in the location shown with a Base Pad Spacer (13) and a 1" Screw (2).
5. Hold a Bolt Spacer (80) inside the lower end of the Right Upright (78). Insert a 3/8" x 4 1/4" Bolt (6) with a 3/8" Star Washer (9) into the Right Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (80), 3/8" x 4 1/4" Bolt (6), and 3/8" Star Washer (9). 5 6 78 9 38 Hold the Right Upright Spacer (79) and the Right Upright (78) against the Base (83). Be careful not to pinch the Upright Wire (38). Partially tighten the two 3/8" x 4 1/4" Bolts (6); do not fully tighten the Bolts yet.
8. See the upper inset drawing. Orient the Right Handrail Spacer (98) with the Right Upright (78) as shown. Insert the Upright Wire (38) and wire tie through the Right Upright Spacer and press the Spacer onto the Upright. 8 Wire Tie 38 98 96 Have a second person hold the Handrail (96) near the Right Upright (78). Remove the wire tie from the Upright Wire (38). 78 38 View A 52 Connect the Upright Wire (38) to the Handrail Wire (52). See the lower inset drawing.
. With the help of a second person, hold the console assembly near the Handrail Base (96). Connect the Handrail Wire (52) to the console wire. See the lower inset drawing in step 8. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.
12. Raise the Frame (56) to the position shown. Have a second person hold the Frame until this step is completed. 12 56 Orient the Storage Latch (53) so that the large barrel and the Latch Knob (54) are oriented as shown. 8 Attach the Latch Bracket (109) and Storage Latch (53) to the Base (83) with two 3/8" x 2" Bolts (4) and two 3/8" Nuts (8). 4 53 54 Large Barrel Attach the upper end of the Storage Latch (53) to the bracket on the Frame (56) with a 3/8" x 2" Bolt (4) and a 3/8" Nut (8).
HOW TO USE THE CHEST PULSE SENSOR HOW TO PUT ON THE CHEST PULSE SENSOR each use, it may remain activated longer than necessary, draining the battery prematurely. The chest pulse sensor consists of two components: the chest strap and the sensor unit (see the drawing below). Insert the tab on one end of the chest strap into one end of the sensor unit, as shown in the inset drawing. Press the end of the sensor unit under the buckle on the chest strap.
OPERATION AND ADJUSTMENT THE PRE-LUBRICATED WALKING BELT Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD This product must be earthed.
CONSOLE DIAGRAM Key FEATURES OF THE CONSOLE This revolutionary treadmill console offers a selection of features designed to make your workouts more effective and enjoyable. When you use the manual mode of the console, you can change the speed and incline of the treadmill with the touch of a button. As you exercise, the console will display continuous exercise feedback.
HOW TO TURN ON THE POWER HOW TO USE THE MANUAL MODE IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room temperature before turning on the power. If you do not do this, the console displays or other electrical components may become damaged. 1. Insert the key into the console. Plug in the power cord (see page 13). Next, locate the reset/off circuit breaker on the treadmill frame near the power cord. Switch the circuit breaker to the reset position.
5. Follow your progress with the display. (see page 12 for information about the chest pulse sensor). Note: If you hold the handgrip pulse sensor and wear the chest pulse sensor at the same time, the console will not display your heart rate accurately. The console offers several display options. The display option you select will determine which workout information is shown. Press the Display button repeatedly to select the desired display option.
HOW TO USE A PERSONAL TRAINER WORKOUT The program will continue in this way until the last segment of the profile flashes in the display and the last segment ends. The walking belt will then slow to a stop. 1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 15. If the speed or incline setting for the current segment is too high or too low, you can manually override the setting by pressing the Speed and Incline buttons.
HOW TO USE THE IFIT COMPETITION TRAINING CENTER 3. Follow your progress with the display. The console offers several display options. The display option you select will determine which workout information is shown. Press the Display button repeatedly to select the desired display option. 1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 15. As you walk or run on the treadmill, the display can show the following workout information: 2. Select the iFIT Competition Training Center.
• A profile of the incline settings of the race. HOW TO USE THE SETTINGS MODE • A status bar showing your progress in the race. 1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 15. • Your average speed. • The rate at which your opponents recover their energy (rec). 2. Select the settings mode. • The bank of energy your opponents have left. To select the settings mode, press the Select Event button. Highlight the SETTINGS option and press the Enter button.
THE INFORMATION MODE HOW TO ADJUST THE CUSHIONING SYSTEM The console features an information mode that allows you to select a unit of measurement for the console, turn on or turn off the display demo mode, and change the contrast of the display. Remove the key from the console and unplug the power cord. The treadmill features a cushioning system that reduces the impact as you walk or run on the treadmill.
HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Before folding the treadmill, adjust the incline to the lowest position. If you do not do this, you may damage the treadmill when you fold it. Remove the key and unplug the power cord. CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill. 1. Hold the metal frame firmly in the location shown by the arrow at the right.
TROUBLESHOOTING Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call the telephone number listed on the back cover of this manual. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 13.) If an extension cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5 m (5 ft.).
Remove the three 3/4" Screws (12) and carefully pivot the Hood (61) off. 12 61 Locate the Reed Switch (71) and the Magnet (50) on the left side of the Pulley (51). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the 3/4" Reed Switch Screw (15), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown).
PROBLEM: The walking belt is off-center or slips when walked on SOLUTION: a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes.
EXERCISE GUIDELINES Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone.
PART LIST—Model No. PETL41307.0 R1207A To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual. Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 29 4 1 6 3 4 4 6 11 1 5 5 2 8 1 1 2 2 2 2 1 1 2 15 10 2 2 14 4 2 2 4 2 4 1 2 3 1 3 4 1 1 2 1 1 2 1 2 2 1 Description Key No. Qty.
Key No. Qty. 101 102 103 104 105 106 107 108 109 110 111 112 113 114 1 2 2 1 2 1 1 1 1 2 1 1 2 1 Description Console Ground Wire Cushion Track Front Cushion Lift Motor Spacer #8 x 2" Screw Reset/Off Circuit Breaker Lift Frame Ground Wire 5/32" Hex Key Latch Bracket 15 1/2" Wire Tie Latch Endcap Controller Ground Wire Receiver Screw Chest Pulse Strap Key No. Qty.
20 31 25 108 30 57 24 3 42 40 32 59 36 58 18 28 25 20 30 67 28 60 31 41 24 28 43 32 40 18 44 28 36 103 25 29 102 90 46 57 25 25 28 45 1 8 55 28 28 17 25 48 49 4 43 28 51 56 54 53 102 90 28 28 25 50 29 17 46 8 49 25 103 1 4 111 48 EXPLODED DRAWING A—Model No. PETL41307.
EXPLODED DRAWING B—Model No. PETL41307.
EXPLODED DRAWING C—Model No. PETL41307.
EXPLODED DRAWING D—Model No. PETL41307.
ORDERING REPLACEMENT PARTS To order replacement parts, see the front cover of this manual.
