User's Manual

ManualsBrandsProForm Manualshealth & beauty(No.PFMC88820)

Heart Rate Monitor User’s Guide

Model No. PFMC89820

Model No. PFMC89920

Congratulations for purchasing the new AccuRate™

heart rate monitor. To install and use the heart rate

monitor, read and follow all instructions in this

user’s guide. For detailed instructions about using

the heart rate monitor with your exercise equipment,

refer to the user’s manual included with your exercise

equipment.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following conditions: (1)

this device may not cause harmful interference, and

(2) this device must accept any interference re-

ceived, including interference that may cause unde-

sired operation. Changes or modifications not ex-

pressly approved by ICON Health & Fitness, Inc.

could void the user’s authority to operate this device.

WARNING

If you have an implanted medical device such

as a pacemaker, check with your physician be-

fore using the heart rate monitor.

If you have heart problems, or if you are over 60

years of age and have been inactive, do not use

pulse-driven programs.

If you are taking medication regularly, consult

your physician to find whether the medication

will affect your exercise heart rate.

Summary of content (12 pages)

PAGE 1
Heart Rate Monitor User’s Guide Congratulations for purchasing the new AccuRate™ heart rate monitor. To install and use the heart rate monitor, read and follow all instructions in this user’s guide. For detailed instructions about using the heart rate monitor with your exercise equipment, refer to the user’s manual included with your exercise equipment. This device complies with Part 15 of the FCC rules.
PAGE 2
How to Install the Receiver Before the heart rate monitor can be used, the included receiver must be installed. To install the receiver in an exercise cycle or an elliptical crosstrainer, refer to the instructions in your exercise cycle user’s manual or elliptical crosstrainer user’s manual. After you have installed the receiver, refer to pages 10 and 11 of this user’s guide. Note: If you have lost your user’s manual, go to www.iconservice.com on the World Wide Web, or call toll-free 1-800-999-3756.
PAGE 3
1. Make sure that the power cord is unplugged. Remove the indicated Screws (A) from the Console Back (B). 1 E B A 2. Peel the paper off the pad on the bottom of the Receiver (C). Turn the Receiver so the cylinder is on the side shown, and press the Receiver into the bottom of the Console Back (B) in the indicated location. Connect the included Short Jumper Wire (D) to the wire on the Receiver (C). Connect the other end of the Short Jumper Wire to the PULSE jack on the back of the Console (E).
PAGE 4
1. Make sure that the power cord is unplugged. Remove the indicated Screws (A) from the Console Back (B). Remove the Console Back from the Console Base (C). 1 B C A 2. Connect the included Long Jumper Wire (D) to the wire on the Receiver (E). Feed the Long Jumper Wire through the Console (F) as shown. Connect the other end of the Long Jumper Wire to the PULSE jack on the back of the Console. If there is a wire already plugged into the PULSE jack, unplug it.
PAGE 5
1. Make sure that the power cord is unplugged. Remove the indicated Screws (A) from the Console Back (B). Remove the Console Back from the Console Base (C). 1 B C A 2. Have a second person hold the Console Base (C) as you remove the indicated Screws (D) from the Console Base. 3. Connect the included Long Jumper Wire (E) to the PULSE jack on the back of the Console (F). If there is a wire already plugged into the PULSE jack, unplug it.
PAGE 6
Note: If you have a PROFORM 785Pi or model number PFTL79100, please call 1-800-999-3756. 1 B A 1. Make sure that the power cord is unplugged. Remove the indicated Screws (A) from the Console Back (B). Remove the Console Back from the Console Base (E). 2. Locate the loose Pulse Wire (C) inside the Console Base (E). Connect the Pulse Wire to the wire on the Receiver (D). Next, peel the paper off the pad on the bottom of the Receiver.
PAGE 7
These instructions are to be used with a treadmill that has a TV and resembles the treadmill shown in the drawings at the right. 1 C A Screws 1. Make sure that the power cord is unplugged. Remove the indicated Screws from the Console Back (A). Important: The Screws may be different lengths. Keep track of which Screws were removed from which holes. 2. Raise the Console (C) enough to view the back of the Console. Peel the paper off the pad on the bottom of the Receiver (B).
PAGE 8
1. Make sure that the power cord is unplugged. Remove the indicated Screws from the Console Back (A). 1 C Important: The Screws may be different lengths. Keep track of which Screws were removed from which holes. A Screws 2. Peel the paper off the pad on the bottom of the Receiver (B). Turn the Receiver so the cylinder is on the side shown, and press the Receiver into the bottom of the Console Base (D) in the indicated location. 2 B Cylinder D 3.
PAGE 9
1. Make sure that the power cord is unplugged. Remove the indicated Screws (A) from the Console Back (B). Remove the Console Back from the Console Base (C). 1 B C A 2. Connect the included Long Jumper Wire (D) to the wire on the Receiver (E). Feed the Long Jumper Wire through the Console (F) as shown. Connect the other end of the Long Jumper Wire to the PULSE jack on the back of the Console. If there is a wire already plugged into the PULSE jack, unplug it.
PAGE 10
How to Use the Heart Rate Monitor The unique heart rate monitor is specially designed for accuracy, comfort, and durability. To get the best performance from the heart rate monitor, please read the instructions below. tion such as saliva or contact lens solution, wet both electrode areas. Return the sensor unit to a position against your chest.
PAGE 11
Next, hold the heart rate monitor near the console. While holding one thumb stationary, begin tapping the other thumb against the electrode area at a rate of about one tap per second. Check the heart rate reading on the console. HEART RATE MONITOR CARE • Thoroughly dry the heart rate monitor after each use. The heart rate monitor is activated when the electrode areas are wetted and the heart rate monitor is put on; the heart rate monitor shuts off when it is removed and the electrode areas are dried.
PAGE 12
Limited Warranty WHAT IS COVERED—The HEART RATE MONITOR (“product”) is warranted to be free of all defects in material and workmanship. WHO IS COVERED—The original purchaser or any person receiving the product as a gift from the original purchaser. HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the product for one year after the date of purchase.