93099671_A P250008
Limited Lifetime Warranty Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/ or mechanical defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from the date of purchase.
Safety Rules 1 Unpacking Your Fan 2 Installing Your Fan 3 Operating Your Fan 10 Care of Your Fan 11 Troubleshooting 11 Specifications 12 Table of Contents
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity 2. 3. 4. 5. 6. has been turned off at the circuit breaker or fuse box before beginning. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. CAUTION: To reduce the risk of personal injury, use only the screws provided with the electrical box.
1 2 3 4 7 5 8 a b c d 6 Unpack your fan and check the contents. You should have the following items: 1. Mounting Bracket (inside canopy) 2. 6” Ball/Downrod Assembly (hanger pin and locking pin pre-attached) 3. Canopy with Canopy Ring (attached) 4. Decorative Motor Collar Cover 5. 6. 7. 8. Fan Motor Assembly Blade Arms (4) Blades (4) Switch Housing a. Blade attachment hardware (13 screws) b. Mounting hardware (1 blade bracket screw) c.
Tools Required Figures 1, 2, and 3 are examples of different ways to mount the electrical box. Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Figure 3 Mounting Options If there isn’t an existing electrical box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the electrical box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This fan is recommended for standard ceiling mount using the downrod provided with this fan. When using standard ceiling installation with the 6 inch downrod provided, the distance from the ceiling to the bottom of the fan blades will be approximately 12 inches. Standard Ceiling Mounting 1. Remove the canopy ring from the canopy by turning the ring clockwise until it unlocks. (Figure 5) 2.
Close-to-Ceiling Mounting 1. Remove the canopy ring from the canopy by turning the ring to the right until it locks. (Figure 5) 7. Align the mounting holes in the canopy with the screw holes in the motor and fasten using the three screws and lock washers (removed previously). Tighten the mounting screws securely. 2. Remove the mounting plate from the canopy by loosening the four screws on top of the canopy. Remove the two non-slotted screws and loosen the slotted screws.
Installing Fan to the Electrical Box WHEN MOUNTING THE FAN ON A SLOPED CEILING, THE STANDARD BALL/DOWNROD MOUNTING METHOD MUST BE USED. THE MOUNTING BRACKET MUST BE MOUNTED SO THAT THE SLOT OPENINGS ARE ON THE LOWER SIDE BY SLIDING THE MOUNTING BRACKET FROM THE TOP DOWN. 1. Pass the 120-Volt supply wires through the center hole in the mounting bracket. (Figure 11) 2. Install the mounting bracket on the outlet box by using the two screws provided with the outlet box.
Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. (Figure 13) 1. Connect the two green fan ground wires, located on the downrod and mounting bracket, to the household ground wire. 2. Connect the neutral fan (White) wire to the white neutral household wire. 3.
Finishing the Fan Installation STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting bracket. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. 2.
Blade Balancing All blades are grouped by weight. Because natural woods vary in density, the fan may wobble even though the blades are weight matched. The following procedure should correct most fan wobble. Check after each step. 1. Check that all blade screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the ceiling.
Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. The fan shipped from the factory with the reversing switch positioned to circulate air downward. If airflow is desired in the opposite direction, turn your fan off and wait for the blades to stop turning, then slide the reversing switch up (located on the switch housing) to opposite position, and turn fan on again. The fan blades will turn in the opposite direction and reverse airflow.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start 1. 2. Check main and branch circuit fuses or breakers Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. Fan sounds noisy 1. 2.
FAN SIZE SPEED VOLTS 32” Low High 120 120 ©2016 Progress Lighting, Inc. 701 Millennium Blvd., Greenville, SC 29607 All Rights Reserved FAN POWER CONSUMPTION AIRFLOW CFM (WITHOUT LIGHTS) WATTS AIRFLOW EFFICIENCY (HIGHER IS BETTER) CFM/WATT 12 1658 138 34 2519 74 NET WEIGHT 11.69 lbs GROSS CUBE WEIGHT FEET 13 lbs 1.7 12.
Manual de instalación del ventilador de techo 93099671_A P250008
Garantía limitada de por vida Los motores de ventilador Progress Lighting se garantizan al comprador original como libres de defectos eléctricos y/o mecánicos por el tiempo en que estén en posesión de dicho comprador. Los interruptores activados por cadena, los interruptores de reversa, los capacitores y los acabados de metal se garantizan como libres de defectos materiales o de fabricación por un periodo de 1 año desde la fecha de compra.
Normas de seguridad 1 Cómo desempacar el ventilador 2 Cómo instalar el ventilador 3 Cómo usar el ventilador 10 Cuidado del ventilador 11 Solución de problemas 11 Especificaciones 12 Tabla de contenido
LEE Y GUARDA ESTAS INSTRUCCIONES 1. Para disminuir el riesgo de descarga eléctrica, antes de 7. Evita colocar objetos en la trayectoria de las aspas. 2. Todo el cableado tiene que cumplir con el Código Nacional de 9. No usar agua ni detergentes para limpiar el ventilador o las comenzar la instalación asegúrate de que la electricidad ha sido desconectada en el cortacircuitos o en la caja de fusibles. Electricidad ANSI/NFPA 70-1999 y con los códigos locales de electricidad.
1 2 3 4 7 5 8 a b c d 6 Desempaca tu ventilador y revisa el contenido. Debes tener los siguientes artículos: 1. Soporte de montaje (dentro de la cubierta) 2. Conjunto de tubo bajante/esfera de 6” (15.2 cm) (con pasadores de soporte y de cierre prefijados) 3. Cubierta con aro de cubierta (acoplado) 4. 5. 6. 7. 8. Cubierta decorativa del collarín del motor Conjunto motor-ventilador Brazos de aspas (4) Aspas (4) Caja del Interruptor a. Herrajes de montaje de aspas (13 tornillos) b.
Herramientas necesarias Destornillador Phillips o de punta plana, llave ajustable, escalera de tijera y cortacables. Las figuras 1, 2 y 3 ejemplifican diferentes maneras de montar la caja eléctrica. Provee un soporte fuerte Placa de montaje en cielo raso Caja eléctrica empotrada Opciones de montaje Figura 3 Si no hay una caja eléctrica presente, lee las siguientes instrucciones. Desconecta la energía retirando los fusibles o apagando los cortacircuitos.
Cómo colgar el ventilador Turn Canopy Ring topara Remove Gira el aro de la cubierta quitarlo RECUERDA cortar el suministro de electricidad. correctamente en la cubierta del collarín y desliza enseguida la cubierta del collarín por el tubo bajante hasta quedar sobre la carcasa del motor. Asegúrate de que tanto la cubierta como la cubierta del collarín estén orientadas correctamente.
Instalacion Proxima al Techo 1. Retire el anillo de la marquesina girandolo hacia la deracha hasta que se desenganche. (Figura 5) 7. Alinea los orificios de montaje de la cubierta con los orificios para los tornillos del motor y asegura con los tres tornillos y arandelas de seguridad (retirados anteriormente). Aprieta bien los tornillos de montaje. 2. Retire la placa de montaje de la marquesina desenroscando los cuatro tornillos ubicados en la parte superior de la marquesina.
Cómo Instalar el Ventilador en la Caja Eléctrica PRECAUCIÓN PARA MONTAR EL VENTILADOR EN CIELO RASO INCLINADO TIENE QUE EMPLEARSE EL MÉTODO ESTÁNDAR DE MONTAJE CON TUBO BAJANTE Y ESFERA. EL SOPORTE DE MONTAJE TIENE QUE INSTALARSE DE MANERA TAL QUE LAS ABERTURAS DE RANURA QUEDEN EN EL LADO INFERIOR, DESLIZANDO EL SOPORTE DE MONTAJE DE ARRIBA ABAJO. 1. Pasa los cables de suministro de 120 V a través del orificio central en el soporte de montaje deslizante. (Figura 11) 2.
1. Conecta los dos cables verdes de conexión a tierra del ventilador, ubicados en el tubo bajante y el soporte de montaje, al cable de conexión a tierra del hogar. 2. Conecta el cable neutro (blanco) del ventilador al cable neutro blanco del circuito eléctrico del hogar. 3. Conecta los cables de alimentación del ventilador (negro) y del kit de luces (azul) al cable negro de suministro de corriente al hogar como se muestra en la Figura 13. 4.
Cómo finalizar la instalación del ventilador MONTAJE ESTÁNDAR EN TECHO ADVERTENCIA EN EL MONTAJE ESTÁNDAR DE TUBO BAJANTE Y ESFERA, LA PESTAÑA EN EL ARO DE LA PARTE INFERIOR DE LA PLACA DE MONTAJE TIENE QUE ENCAJAR EN LA RANURA DE LA ESFERA DE SOPORTE. SI NO ENCAJA BIEN, PUEDE DAÑARSE EL CABLEADO. 1. Alinea las ranuras de cierre de la cubierta de techo con los dos tornillos del soporte de montaje. Empuja hacia arriba para enganchar las ranuras y gira de izquierda a derecha para asegurarlas en su sitio.
Cómo equilibrar las aspas Tocando el techo Todas las aspas se agrupan por peso. Puesto que las maderas naturales varían en densidad, el ventilador puede oscilar aunque las aspas tengan el mismo peso. El siguiente procedimiento corregirá en gran medida la oscilación del ventilador. Verifica después de cada paso. 1. Verifica que todos los tornillos de las aspas estén asegurados. 2. La mayoría de los problemas de oscilación del ventilador se deben a que las aspas no están al mismo nivel.
Las configuraciones de velocidad para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del techo, la cantidad de ventiladores y otras. Este ventilador se envía desde la fábrica con el interruptor de reversa en posición de hacer circular el aire hacia abajo.
Cuidado del ventilador Aquí tienes algunas sugerencias para el mantenimiento de tu ventilador. 1. Por causa del movimiento natural del ventilador, algunas conexiones pueden aflojarse. Revisa las conexiones de soporte, los soportes y los accesorios de aspas dos veces al año. Comprobar que estén seguros. (No es necesario desmontar el ventilador del cielo raso). 2. Hay que limpiar el ventilador con frecuencia para que luzca como nuevo al paso de los años.
TAMAÑO DEL VENTILADOR 81.3 cm VELOCIDAD VOLTIOS (V) CONSUMO DE ENERGÍA DEL VENTILADOR (SIN LAS LUCES) EN VATIOS FLUJO DE AIRE EN PIES CÚBICOS POR MINUTO (CFM). EFICIENCIA DE FLUJO DE AIRE (MIENTRAS MÁS ALTO EL NÚMERO, MEJOR) CFM/W Baja 120 12 1658 138 Alta 120 34 2519 74 ©2016 Progress Lighting, Inc. 701 Millennium Blvd., Greenville, SC 29607 Todos los derechos reservados PESO NETO PESO BRUTO PIES CÚBICOS 11.69 lb 13 lb 1.7 12.