® P250009
Limited Lifetime Warranty Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from the date of purchase.
Safety Rules 1 Unpacking Your Fan 2 Installing Your Fan 3 Making the Electrical Connections 6 Operating Your Fan 11 Care of Your Fan 12 Troubleshooting 12 Specifications 13 Table of Contents
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity has been 2. 3. 4. 5. 6. 7. turned off at the circuit breaker or fuse box before beginning. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. CAUTION: To reduce the risk of personal injury, use only the screws provided with the electrical box.
1 6 2 7 3 4 比例 25.400 5 10 2h 2 4h 3 4 OFF 1 6 a 8h b 5 R 8 11 9 Unpack your fan and check the contents. You should have the following items: 1. Mounting Bracket (inside canopy) 2. 6” Ball/Downrod Assembly (hanger pin and locking pin pre-attached) 3. Canopy with Canopy Ring (attached) 4. Decorative Motor Collar Cover 5. Fan Motor Assembly 6. Blades (4) 7. Light Kit Pan 8. Light Kit Fitter Assembly 9. Glass Shade 10. Transmitter and Receiver 11. Extension Lead Wire a.
Tools Required Figures 1, 2, and 3 are examples of different ways to mount the electrical box. Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Figure 3 Mounting Options If there isn’t an existing electrical box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the electrical box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan Turn Canopy Ring to Remove REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This fan is recommended for standard ceiling mount using the downrod provided with this fan. When using standard ceiling installation with the 6 inch downrod provided, the distance from the ceiling to the bottom of the fan blades will be approximately 14 inches. Standard Ceiling Mounting 3. Remove the hanger pin and locking pin from downrod assembly. 4.
Installing Fan to the Electrical Box Connecting the Safety Cable 1. Turn the wood screw (LL)(not provided) into the ceiling. WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING BRACKET MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 8. 2.
Installing the Receiver into the Mounting Bracket 1. Position the house supply wires to one side of the slide-on mounting bracket; position the fan wires to the opposite sid. 2. Insert the narrow end of the receiver (as shown, flat side toward ceiling) into the slide-on mounting bracket until it rests on top of the ball/downrod assembly. (Figure 11) Wiring the Fan to the Receiver 1. If using the 6 in.
Finishing the Fan Installation STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting plate. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. 2.
Blade Balancing All blades are grouped by weight. Because natural woods vary in density, the fan may wobble even though the blades are weight matched. Touching Ceiling The following procedure should correct most fan wobble. Check after each step. 1. Check that all blade screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades.
Installing the Light Kit Pan/Light Kit Fitter Assembly/ Glass Shade CAUTION - To reduce the risk of electrical shock, disconnect the electrical supply circuit to the fan before installing the light kit. 1. Loosen but do not remove two of three mounting screws from the fan motor assembly; Remove one mounting screw. (Figure 15) 2. Push the light kit pan up to the fan motor assembly so that the two loosened screw heads fit into the keyhole slots. Turn the light kit pan clockwise, tightened the screws.
CFL 0 LEARN D 1 D 1. Remove the battery cover by pressing firmly on the arrow and sliding the cover off. CFL 0 NOTE: The remote control has already been paired to the ceiling fan for your convenience. If you have two of the same model fans in your home , please follow the steps below to control each fan independently. 1 Preparing the Remote Control LEARN 2. Install two 1.5V AAA batteries (N) (included). 3. Slide the dip switch in the battery compartment to the “1” setting. Figure 18 4.
Remote Control Timer: While the fan is on press 2h - turns on a 2 hour run timer. While the fan is on press 4h - turns on a 4 hour run timer. While the fan is on press 8h - turns on an 8 hour run timer. Forward/Reverse: Changes direction of ceiling fan. Breeze: Press and release this button to enable the Breeze function, this will change your fan speed randomly, simulating a relaxing breeze. Fan speed: LEDs on the fan speed button will illuminate to the corresponding speed.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start Here are some suggestions to help you maintain your fan. 2. Clean your fan periodically to help maintain its new appearance over the years.
FAN SIZE 56” SPEED Low High VOLTS 120 FAN POWER CONSUMPTION AIRFLOW (WITHOUT LIGHTS) CFM WATTS AIRFLOW EFFICIENCY (HIGHER IS BETTER) CFM/WATT 1.77 2798 1581 20.5 7801 381 NET WEIGHT GROSS WEIGHT CUBE FEET 28.88 Lbs 31.97 Lbs 2.55 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.