® 93089915_B B P2560
Limited Lifetime Warranty Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from the date of purchase.
Safety Rules 1 Unpacking Your Fan 2 Installing Your Fan 3 Setting the Codes on Remote Control and Receiver 6 Making the Electrical Connections 7 Finishing the Fan Installation 8 Operating Your Fan 10 Care of Your Fan 11 Troubleshooting 11 Specifications 12 Table of Contents
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity has 2. 3. 4. 5. 6. been turned off at the circuit breaker or fuse box before beginning. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. CAUTION: To reduce the risk of personal injury, use only the screws provided with the electrical box.
1 a b 5 2 9 M OK 6 c 3 7 4 8 THIS SIDE UP Unpack your fan and check the contents. You should have the following items: 1. Mounting Bracket (inside canopy) 2. 8” Ball/Downrod Assembly (hanger pin and locking pin pre-attached) 3. Canopy with Canopy Ring (attached) 4. Decorative Motor Collar Cover 5. 6. 7. 8. 9. Fan Motor Assembly Switch Cup Adaptor Switch Cup Blade (5) Transmitter and Receiver a. Blade attachment hardware (16 Screws) b.
Tools Required Figures 1, 2, and 3 are examples of different ways to mount the electrical box. Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Figure 3 Mounting Options If there isn’t an existing electrical box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the electrical box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This fan is recommended for standard ceiling mount using the downrod provided with this fan. When using standard ceiling installation with the 8 inch downrod provided, the distance from the ceiling to the bottom of the fan blades will be approximately 15 inches. Standard Ceiling Mounting 1. Remove the canopy ring from the canopy by turning the ring counter-clockwise until it unlocks. (Figure 5) 2.
Installing Fan to the Electrical Box WHEN MOUNTING THE FAN ON A SLOPED CEILING, THE STANDARD BALL/DOWNROD MOUNTING METHOD MUST BE USED. THE MOUNTING PLATE MUST BE MOUNTED SO THAT THE SLOT OPENINGS ARE ON THE LOWER SIDE BY SLIDING THE MOUNTING PLATE FROM THE TOP DOWN. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 8. 2.
Setting the Codes R Model:UC7085T FCC ID:CHQ7085T IC:2968A-7085T Complies with Canada RSS-210 MADE IN CHINA A. Remove the battery cover from the battery compartment in the back side of the transmitter. 2 3 4 2 3 4 DIP 4 1 ON 2 ON 3 4 DIP Receiver 3 Dip Switches 12V B. Slide code switches to your choice of up or down position (factory setting is up). C. Replace the battery cover on the battery compartment of the transmitter. 2 ECE N 1 ECE N 1 ON 1.
2. 3. IF OTHER FAN OR SUPPLY WIRES ARE DIFFERENT, PLEASE HAVE THIS UNIT INSTALLED BY A LICENSED ELECTRICIAN. USE THE PLASTIC WIRE CONNECTORS SUPPLIED WITH YOUR FAN. SECURE THE CONNECTORS WITH ELECTRICAL TAPE AND ENSURE THERE ARE NO LOOSE STRANDS OR CONNECTIONS. EACH WIRE NUT (WIRE CONNECTOR) SUPPLIED WITH THIS FAN IS DESIGNED TO ACCEPT UP TO ONE 12 GAUGE HOUSE WIRE AND TWO WIRES FROM THIS FAN.
STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting plate. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. 2.
Attaching the Fan with the Optional Light Fixture (not supplied) Attaching the Switch Cup Adaptor/ Attaching the Switch Cup For optional light fixture installation, remove the reverse module and the bottom cover to easily feed the light kit wires through the threaded hole in the center of the switch housing (Figure 16). After the light kit is attached to the switch cup, replace the module to its original position.
Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. Remote control - Your fan is equipped with a remote control to operate the speed and lights of your new ceiling fan.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start Here are some suggestions to help you maintain your fan. 2. Clean your fan periodically to help maintain its new appearance over the years.
FAN SIZE 68” SPEED Low Med High VOLTS 120 FAN POWER CONSUMPTION AIRFLOW CFM (WITHOUT LIGHTS) WATTS 30 58 86 3767 5641 7045 AIRFLOW EFFICIENCY (HIGHER IS BETTER) CFM/WATT 126 97 82 NET WEIGHT 31.53 Lbs GROSS CUBE WEIGHT FEET 36.16 Lbs 4.1 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
® Manual de instalación del ventilador de techo 93089915_B B P2560
Garantía limitada de por vida Los motores de ventilador Progress Lighting se garantizan al comprador original como libres de defectos eléctricos y/o mecánicos por el tiempo en que estén en posesión de dicho comprador. Los interruptores activados por cadena, los interruptores de reversa, los capacitores y los acabados de metal se garantizan como libres de defectos materiales o de fabricación por un periodo de 1 año desde la fecha de compra.
Normas de seguridad 1 Cómo desempacar el ventilador 2 Cómo instalar el ventilador 3 Cómo configurar los códigos del control remoto y el receptor 6 Cómo hacer las conexiones eléctricas 7 Cómo finalizar la instalación del ventilador 8 Cómo usar el ventilador 10 Cuidado del ventilador 11 Solución de problemas 11 Especificaciones 12 Tabla de contenido
LEE Y GUARDA ESTAS INSTRUCCIONES 1. Para disminuir el riesgo de descarga eléctrica, antes de comenzar la instalación asegúrate de que la electricidad ha sido cortada en el cortacircuitos o en la caja de fusibles. 2. Todo el cableado tiene que cumplir con el Código Nacional de Electricidad ANSI/NFPA 70-1999 y con los códigos locales de electricidad. La instalación eléctrica debe hacerse por un electricista calificado con licencia. 3.
1 a b 5 2 9 M OK 6 c 3 7 4 8 THIS SIDE UP Desempaca tu ventilador y revisa el contenido. Debes tener los siguientes artículos: 1. Soporte de montaje (dentro de la cubierta) 2. Conjunto de tubo bajante/bola de 8” (20.3 cm) (pasadores de soporte y de cierre prefijados) 3. Cubierta con aro de cubierta (acoplado) 4. Cubierta decorativa del collarín del motor 5. Conjunto motor-ventilador 6. 7. 8. 9. Adaptador de la caja del interruptor Caja del interruptor Aspas (5) Transmisor y receptor a.
Herramientas necesarias Las figuras 1, 2 y 3 ejemplifican diferentes maneras de montar la caja eléctrica. Provee un soporte fuerte Destornillador Phillips o de punta plana, llave ajustable, escalera de tijera y cortacables. Placa de montaje en techo Caja eléctrica empotrada Opciones de montaje Figura 3 Si no hay una caja eléctrica presente, lee las siguientes instrucciones. Desconecta la energía retirando los fusibles o apagando los cortacircuitos.
Cómo colgar el ventilador RECUERDA cortar la corriente. Sigue los pasos Turn Canopy Ring to para Remove Gira el aro de la cubierta quitarlo 7. Vuelve a apretar los tornillos del collarín en la parte superior de la carcasa del motor. más abajo para colgar correctamente tu ventilador. NOTA: Se recomienda instalar este ventilador en techo interior estándar usando el tubo bajante incluido. Cuando uses una instalación de techo estándar con el tubo bajante de 8 pulgadas (20.
Cómo instalar el ventilador en la caja eléctrica PRECAUCIÓN AL INSTALAR EL VENTILADOR EN UN TECHO INCLINADO, TIENES QUE HACERLO POR EL MÉTODO DE MONTAJE ESTÁNDAR CON TUBO BAJANTE Y BOLA. LA PLACA DE MONTAJE TIENE QUE INSTALARSE DE MANERA TAL QUE LAS ABERTURAS DE RANURA QUEDEN SOBRE EL LADO INFERIOR, DESLIZANDO LA PLACA DE MONTAJE DESDE LA PARTE SUPERIOR HACIA ABAJO. 1. Pasa los cables de alimentación de 120 V a través del orificio central en el soporte de montaje de techo como muestra la Figura 8. 2.
Transmisor Transmitter Airpro 3 2 3 4 DIP 3 4 1 ON 2 ON 3 4 DIP Receiver Receptor 2 Interruptores Dip enSwitches línea 4 12V ON C. Coloca de nuevo la cubierta sobre el compartimento de las baterías del transmisor. 2 ECE N 1 ECE N 1 1. Cómo configurar el código del transmisor: B. Desliza los interruptores de código como desees, hacia arriba o hacia abajo (la configuración de fábrica es hacia arriba).
Modelo del control remoto: UC7067RYE NOTA SI LOS CABLES DE ALIMENTACIÓN O DE OTROS VENTILADORES SON DIFERENTES, BUSCA UN ELECTRICISTA CON LICENCIA PARA INSTALAR LA UNIDAD. NOTA USA LOS CONECTORES DE CABLES PLÁSTICOS INCLUIDOS CON TU VENTILADOR. SUJETA LOS CONECTORES CON CINTA DE ELECTRICISTA Y ASEGÚRATE DE QUE NO HAYA CONEXIONES NI CABLES SUELTOS.
MONTAJE ESTÁNDAR EN TECHO ADVERTENCIA EN EL MONTAJE ESTÁNDAR DE TUBO BAJANTE Y BOLA, LA PESTAÑA EN EL ARO DE LA PARTE INFERIOR DE LA PLACA DE MONTAJE TIENE QUE ENCAJAR EN LA RANURA DE LA BOLA DE SOPORTE. SI NO ENCAJA BIEN LA LENGÜETA EN LA RANURA, PUEDE DAÑARSE EL CABLEADO. 1. Alinea las ranuras de cierre de la cubierta de techo con los dos tornillos de la placa de montaje. Empuja hacia arriba para enganchar las ranuras y gira de izquierda a derecha para asegurarlas en su lugar.
Cómo instalar el ventilador con la lámpara de luz opcional (no suministrada) Cómo instalar el adaptador de la caja del interruptor/ Cómo instalar la caja del interruptor PRECAUCIÓN - Para reducir el riesgo de descarga eléctrica, desconecta el circuito eléctrico de alimentación al ventilador antes de instalar el kit de luces. 1. Quita un tornillo del soporte negro debajo del conjunto motor-ventilador. Afloja los otros dos tornillos, sin quitarlos.
Las configuraciones de velocidad para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del techo, la cantidad de ventiladores y otras. Control remoto - Tu ventilador está equipado con un control remoto que controla la velocidad y las luces.
Cuidado del ventilador Solución de problemas 1. Por causa del movimiento natural del ventilador, algunas conexiones pueden aflojarse. Revisa dos veces al año las conexiones de soporte, los soportes y los accesorios de las aspas. Comprueba que estén seguros. (No es necesario desmontar el ventilador del techo). El ventilador no enciende Aquí tienes algunas sugerencias para dar mantenimiento a tu ventilador. 2. Limpia el ventilador con frecuencia para que luzca como nuevo al paso de los años.
TAMAÑO DEL VENTILADOR 68” (1.72 m) VELOCIDAD Baja Media Alta VOLTIOS 120 CONSUMO DE ENERGÍA DEL VENTILADOR (SIN LAS LUCES) EN VATIOS FLUJO DE AIRE EN PIES CÚBICOS POR MINUTO (CFM) EFICIENCIA DE FLUJO DE AIRE (MIENTRAS MÁS ALTA MEJOR) CFM/W 30 3767 126 58 86 5641 7045 97 82 PESO NETO PESO BRUTO PIES CÚBICOS 31.53 Lbs 36.16 Lbs 4.