Instructions / Assembly

This remote control is designed to separately control your ceiling fan speed and light brightness.
There are four buttons • • • , • • , • , to control the fan speed and off.
The light button will control the lights
The light button will turn the lights on/off and full range dim
The green indicator on the transmitter will light when the button is pressed.
INSTALLATION AND OPERATING INSTRUCTION
1. SETTING THE CODE
This unit has 16 different code combinations. To set the code, perform these steps
A. Setting the code on the transmitter.
a. Remove battery cover. Press firmly below arrow and slide battery cover off.
b. Slide code switches to your choice of up or down position. Factory setting is
all up. Do not use this position. Use a small screwdriver or a ball point pen to
slide firmly up or down (Figure 1 ) .
B. Setting the code on the receiver.
a. Slide code switches to the same positions as set on your transmitter (Figure 2).
b. Replace battery cover on transmitter.
2.INSTALLING RECEIVER IN CEILING FAN
A. Safety precautions:
·WARNING: HIG H VOLTAGE!
• Do not use solid state fan speed control or light dimmer wall control.
• Electrical wiring must meet all local and national electrical code requirements.
TRANSMITTER
• Electrical source and fan must be 115/120 volt. 60Hz. Max i mum fan motor amps: 1. 0 . Maximun light watts:300W (incandescent)
·Household electrical power can cause serious injury or death!
B. Install i ng receiver in fan:
a. Tu m electricity off at main circuit breaker panel before beginning installation.
b. Remove ceiling fan canopy from the mounting bracket
c. Disconnect existing wiring between ceiling fan and supply at
electrical junction box .
d. Make connections as follows, using the wire nuts supplied:
Connect BLACK Control Unit wire to BLACK supply wire (AC L).
Connect WHITE Control Unit wire to WHITE wire of supply (AC N )
Connect WHITE Control Unit wire (MOTOR N) to WHITE fan wire.
Connect BLACK Control Unit wire (MOTOR L) to BLACK fan w ire.
Connect BLUE Control Unit wire (FOR LIGHT) to BLUE light wire.
If other fan or supply wires are different colors, have this unit installed by qualified licensed electrician.
e. Push all connected wires up into junction box.
f. Lay the black antenna wire on top of the receiver, and put the receiver in the mounting bracket.
g. Reinstall the canopy on the mounting bracket.
h. Restore electrica l power.
3. OPERATING TRANSMITTER :
CAUTION:
Do not use fan speed control in canopy where the
mounting bracket is not described in Figure 4.
A. lnstall 12 volt battery (included) . To prevent damage to transmitter, remove the battery if not use for long period.
B. Store the transmitter away from excess heat or humidity.
C. This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other
remote units such as garage door openers, car alarm or security system. If you find that your fan and light
kit go on and off without using your remote control, simply change the combination code in your
transmitter and receiver.
D. Operation buttons on the panel of the transmitter.
• • • key-for fan high speed .
• • key for fan medium speed.
• key for fan low speed.
key-for fan speed off.
key for lights on/off and hold to dim
key-Reverse the fan's direction of rotation (if fan has a reverse receiver)*
The light function is controlled by pressing the key. Hold key down to increase or decrease light. Tap key quickly to turn
light off or on
Keep pressing the button in excess of 0.7 second, it becomes dimmer, the light varies cyclically in 0.8 second.
* The fa n must be running on any speed before the "reverse" button is depressed
E. Memory function:
When the fan or light is turned off by the wall control, it will memorize and recover automatically to the last fan speed and/or light
4.TROUBLE SHOOTING GUIDE
1. Fails to operate:
a. Power to receiver ?
b. Receiver wired correctly ?
c. Fan manual speed control in highest position ?
d. Light kit switch turned on ?
e. Good battery in the transm i tter ?
f. Code set at exact same positions in both transmitter and receiver ?
2 . Won't operate at distance
If transmitter operates fan/light kit when up c l ose, but not at 30 feet away,
try placing the black antenna wire higher, up through ceiling/outside the junction box.
NOTICE:
your ceiling fan and light kit assembly must
meet the following requ i rements:
1. Do not use with solid state fans
2. Electrical rating: 120V 60Hz 3.5A
MAX. motor amps: 1.5
MAX. light watts: 300W ( incandescent )
CAUTION:
Ceiling Angle shall Not Exceed 45 Degrees For
Mounting controller. Models UC-7067RC/UC7067RY