Installation Guide

ManualsBrandsProgress Lighting ManualsLighting6 in. Metallic Firebox New Construction Recessed Housing

(Ceiling Opening is to be 6 7/8"Dia.)

INSTALLATION IN WOOD JOISTS

This Instruction sheet is also intended to be used as a Paint Shield.

Follow this Instruction Sheet Carefully. Be sure Electricity is OFF before starting Installation.

1.- Slip Bar Hangers (1) through slots in Plaster Frame (2). Hold Frame in desired position between

Joists (3) and drive Bar Hanger Tabs (4) into Joists. Use a minimum 1" lg. steel Nail or Screw (26)

through holes in Bar Hanger ends for additional support. Tighten bar hanger Locking Screws (5) in

ends of Plaster Frame to prevent lateral movement of Plaster Frame. (See Fig. 1 and 2)

2.- Remove Cover Plate (9) from Junction Box (10). Slip Type NM Cable (Romex) (11) through desired

hole in Junction Box (10) above Retaining Plate (13). Cable (11) is secured by Retaining Plate (13).

(See Fig. 3)

3.- If other than Type NM Cable (Romex) is to be used, remove one Large Knockout (15) at desired

location on top or sides of Junction Box (10). Bring appropriate Electrical Supply Cable into Junction

Box and secure in place with proper UL listed Connector (NOT FURNISHED).

4.- Connect Fixture Wires (27) to Supply Wires (16) as shown in Wiring Diagram. Use UL listed

Wirenuts (NOT FURNISHED).

5.- After ceiling is finished, lower Housing (6) until flush with Ceiling.

6.- To gain access to Junction Box (10), after Ceiling is finished, remove three Screws (24) that hold

Housing (6) in place. Lower the Housing. Remove Screw (21) and Access Door (22) located inside

Fixture. Junction Box Cover Plate (9) can now be removed for service.

7.- Plaster Frame (2) and Gasket (25) must be in contact with Ceiling (23).

8.- If joists are spaced greater than 16 inches on center, 2x4 (4 inch dimension vertical) or greater

lumber shall be used to span between joists at the plane of the ceiling to create a 16 inch on center

space to mount the fixture as shown in Fig. 4.

9.- If steel furring channels are used in the ceiling, Plaster Frame (2) must be lowered until Gasket (25)

contacts Ceiling (23) as shown in Fig. 5.

When installed according to the instructions provided and as specified in Volume 1 of the UL Fire

Resistance Directory, Progress P821-FB & P821-FBT luminaires may be used in fire resistant

Floor-Ceiling and Roof-Ceiling designs. See File #R19217 under Fire Classified Directory CDHW.

SPEC.NO.

Assembly & Installation Instructions

Read instructions carefully and turn electricity off at main

circuit breaker panel before beginning installation.

CAUTION:

PAGE of

01-15-03023567

P821-FB & P821-FBT

1 6

***************************************************************************************************************************************************************

WARNING: - If any Special Control Devices are used with this fixture, follow the instructions carefully

to assure full compliance with N.E.C. requirements. If there are any questions, contact a Qualified

Electrical Contractor.

ARNING: Use only those Trims, Lamps and maximum Wattage's proper for this Fixture, as

indicated on the Label within the Fixture Housing.

ARNING: The National Electrical Code, Article 110-3 (b), states that "Listed or Labeled equipment

shall be used or installed in accordance with any Instructions included in the listing or labeling".

Use only with Progress UL listed Trims. Use of other Trims not listed in this Fixture, including

those that are UL classified, is a violation of N.E.C. 110-3 (b) and voids all warranties.

Upon completion of installation, crumple this sheet up and insert it up into

the housing to protect the socket and labels from being spray painted.

*** This is a Non-IC Housing. Insulation must be kept 3" away from fixture to prevent lights from blinking. ***

Summary of content (6 pages)

PAGE 1
Assembly & Installation Instructions CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation. P821-FB & P821-FBT *************************************************************************************************************************************************************** WARNING: - If any Special Control Devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements.
PAGE 2
Instrucciones de ensamblaje e instalación. Precaución: Lea cuidadosamente las instrucciones y desconecte la electricidad del cortacircuitos principal antes de iniciar la instalación. ****************************************************************************************************************************************** ADVERTENCIA- EN CASO DEL USO DE OTROS MECANISMOS DE CONTROL CON ESTE APARATO DE LUZ, SIGA CUIDADOSAMENTE LAS INSTRUCCIONES PARA CUMPLIR CON LOS REQUISITOS N.E.C. SI UD.
PAGE 3
INSTALLATION INSTRUCTIONS FOR FIRE RATED APPLICATIONS USING T-BAR 1. Install No. 12 SWG Galv. Steel Hanger Wire (28) on Main Runners (29) at four corners of grid module containing Luminaire (30). When Main Runners are spaced greater than 24 in. on center, Cross Tees (31) forming sides of grid module containing Luminaire to be supported by Steel Hanger Wire at Cross Tee midspan. 2. Place the Luminaire (30) on the ceiling grid with the "T" Bars running through the Hanger Bar Notches (32).
PAGE 4
INSTRUCCIONES DE INSTALACIÓN PARA APLICACIONES ANTIINCENDIO USANDO LAS BARRAS "T" 1. Instale el alambre de suspensión de acero galvanizado no. 12 SWG (28) en los rieles principales (29) a los cuatro ángulos del módulo de la rejilla que contiene el aparato de luz (30).
PAGE 5
Instructions d'Assemblage et Installation Mise en garde: Lire les instructions avec soin et couper le courant au disjoncteur central avant de commencer l'installation. ****************************************************************************************************************************************** AVERTISSEMENT: DANS LE CAS OÙ D'AUTRES MÉCANISMES DE COMMANDE S'UTILISENT AVEC CE DISPOSITIF D'ÉCLAIRAGE, SUIVEZ AVEC SOIN LES INSTRUCTIONS POUR ACCÉDER AUX EXIGENCES DU N.E.C.
PAGE 6
4 3 6 1 1 5 15 WHITE SUPPLY WHITE OR IDENTIFIED WIRE FIXTURE WIRE UL LISTED WIRENUTS BLACK SUPPLY PLAIN OR BLACK WIRE FIXTURE WIRE 10 5 2 26 Fig. 1 24 BARE, OR GREEN GROUND WIRE FROM SUPPLY FIXTURE GROUND WIRE 1 4 3 22 21 6 BARE, OR GREEN 10 10 9 11 9 13 1 27 Fig. 3 4 Fig. 2 24 25 9 15 4 23 GREATER THAN 16" 16" 2 Fig. 4 23 25 Fig.