User Manual Dishwasher PI1325XC
Progress CONTENTS Safety information Safety instructions Product description Control panel Programmes Settings 2 3 5 6 7 7 Before first use Daily use Hints and tips Care and cleaning Troubleshooting Technical information 9 10 11 13 14 17 Subject to change without notice. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages.
Progress 3 • • • • • • • • • • Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (Mpa) Obey the maximum number of 13 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position.
Progress mains plug, use fuse: 13 amp ASTA (BS 1362). Water connection • Make sure not to cause damage to the water hoses. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. • The water inlet hose has a safety valve and a sheath with an inner mains cable. • Do not drink and play with the water in the appliance.
Progress 5 PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 9 8 7 6 5 4 7 8 9 10 11 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket 3
Progress CONTROL PANEL 1 6 1 2 3 4 On/off indicator Programme marker Indicators Delay button 2 3 5 4 5 Start button 6 Programme knob Indicators Indicator Description Washing phase. It comes on when the washing phase and the rinsing phases operate. Drying phase. It comes on when the drying phase operates. End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates.
Progress 7 PROGRAMMES Programme 2) 3) Degree of soil Type of load Programme phases Normal soil Crockery and cutlery • • • • Normal soil Crockery and cutlery • • • • Fresh soil Crockery and cutlery • Wash 60 °C or 65 °C • Rinses Consumption values 1) Duration (min) Energy (kWh) Water (l) Prewash Wash 50 °C Rinses Dry 195 1.039 11 Prewash Wash 65 °C Rinses Dry 120 130 1.3 - 1.6 15 - 17 30 0.
Progress The water softener The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance. The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area.
Progress 9 • The intermittent flashing of refers to the current set level, e.g. 5 flashes + pause + 5 flashes = level 5. 4. Press Delay again and again to change the setting. Each time you press Delay the level number increases. After level 10 you will start again from level 1. 5. Turn knob to on/off position to confirm the setting. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2.
Progress How to fill the rinse aid dispenser 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks into position. B A M AX 4 1 3 2 + - C D You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity).
Progress 11 Setting and starting a programme Starting a programme 1. Open the water tap. 2. Close the appliance door. 3. Turn the knob until the symbol of a programme you want to set is aligned with the on/off indicator. • On/off indicator comes on. • Start indicator starts to flash. 4. Press Start. • The programme starts . • On/off indicator and start indicator are on. Starting a programme with delay start 1. Set the programme. 2. Press Delay to delay the start of the programme of 3 hours.
Progress efficient use of water and energy consumption for crockery and cutlery with normal soil. Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • Multi-tablets are usually suitable in areas with a water hardness up to 21 °dH. In areas exceeding this limit, rinse aid and salt must be used in addition to the multi-tablets.
Progress 13 At the end of the programme water can still remain on the sides and on the door of the appliance. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). Cleaning the filters The filter system is made of 3 parts. C 4.
Progress Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. External cleaning 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. • Clean the appliance with a moist soft cloth. • Only use neutral detergents.
Progress 15 Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The programme does not start. • Make sure that the appliance door is closed. • Press Start. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener.
Progress Problem and alarm code Possible cause and solution Rattling/knocking sounds from inside the appliance. • The tableware is not properly arranged in the baskets. Refer to basket loading leaflet. • Make sure that the spray arms can rotate freely. The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use.
Progress 17 Problem Possible cause and solution Unusual foam during washing. • Use the detergent for dishwashers only. • There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre. Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together.
Progress Power consumption Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. ENVIRONMENT CONCERNS dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. Recycle the materials with the symbol .
Progress 19
www.progress-hausgeraete.
