Instruction Manual

ManualsBrandsProgressive International Electronics ManualsSensorsConfigurator

PI Configurator Installation Guide

CONTENTS

System Installation Warnings.........................................Page 1

Dispenser Specific Installation ........................................Page 2

Gilbarco Electronic Dispenser...................................Page 2

Diagram: PIE Product to PI Configurator to Gilbarco Dispenser . . . . . Page 3

Diagram: Current Loop PI Config. Jumper Selection — Gilbarco . . . . Page 3

Wayne/Dresser Electronic Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4

Diagram: PIE Product to PI Config. to Wayne Electronic Dispenser . . . Page 5

Diagram: Current Loop PI Config. Jumper Selection — Wayne . . . . . Page 5

Tokheim Electronic Dispenser ...................................Page 6

Diagram: PIE Product to PI Config. to Tokheim 98/94 Power Center . Page 7

Diagram: PIE Product to PI Config. to Tokheim 67 DBox . . . . . . . . . . Page 8

Summary of content (10 pages)

PAGE 1
PI Configurator Installation Guide CONTENTS System Installation Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1 Dispenser Specific Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2 Gilbarco Electronic Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2 Diagram: PIE Product to PI Configurator to Gilbarco Dispenser . . . . . Page 3 Diagram: Current Loop PI Config.
PAGE 2
PI Configurator Manufacturer's Warranty Progressive International Electronics, Inc. (SELLER) warrants to the Purchaser of fuel control equipment manufactured by Seller against defects in material or workmanship for one (1) year from date of shipment. Seller will replace or repair defective parts or replace and issue credits to the Purchaser's account in accordance with the following Conditions of Warranty. CONDITIONS OF WARRANTY 1.
PAGE 3
Installation Guide PI Configurator System Installation System Installation Warnings Safety hazards are inherent with all electrical equipment. Standard precautions must be taken at all times during installation and operation of the PI Configurator units. In addition to normal electrical precautions, the following points should be noted during installation. C Installation must comply with National Electrical Code, as well as Federal, State/Provincial, Local, and all applicable codes.
PAGE 4
Installation Guide PI Configurator Dispenser Specific Installation Gilbarco Electronic Dispenser Note all warnings in System Installation Warnings section. Installation instructions in this manual refer to the specific DBoxes supplied by dispenser manufacturers, used in conjunction with the PI Configurator, in a Progressive International product installation.
PAGE 5
Installation Guide PI Configurator Diagram: PIE Product to PI Configurator to Gilbarco Dispenser Diagram: Current Loop PI Configurator Jumper Selection — Gilbarco Version 2.
PAGE 6
Installation Guide PI Configurator Dispenser Specific Installation Wayne/Dresser Electronic Dispenser Note all warnings in System Installation Warnings section. Installation instructions in this manual refer to the specific DBoxes supplied by dispenser manufacturers, used in conjunction with the PI Configurator, in a Progressive International product installation.
PAGE 7
Installation Guide PI Configurator Diagram: PIE Product to PI Configurator to Wayne/Dresser Electronic Dispenser Diagram: Current Loop PI Configurator Jumper Selection — Wayne Version 2.
PAGE 8
Installation Guide PI Configurator Dispenser Specific Installation Tokheim Electronic Dispenser Note all warnings in System Installation Warnings section. Installation instructions in this manual refer to the specific DBoxes supplied by dispenser manufacturers, used in conjunction with the PI Configurator, in a Progressive International product installation.
PAGE 9
Installation Guide PI Configurator ! For systems with more than 8 dispensers (2 Model 98/94 Computer/Power Centers) — Use a “Y” cable (available from PIE) between the PI-TOK data cable and the Model 98/94 Computer/Power Centers. See Diagram: PIE Product to PI Configurator to Two Tokheim 98/94 Power Centers. Cables must be screw-locked together. The connection must be in a sheltered environment, protected from harsh elements such as water, extreme heat or cold, etc. 4. Proceed with programming of system.
PAGE 10
Installation Guide PI Configurator For Dispensers Using Model 67 or 67B DBox The 67 and 67B DBoxes are similar. Be sure to determine model number from nameplate before attempting to connect to this device or damage may occur. 1. Disconnect the Tokheim console (if applicable) from the 67/67B distribution box and connect the Tokheim 67/67B style PI Configurator to the 67/67B DBox and to the PIE product, using the appropriate cables supplied by PIE.