BABY MONITOR SYSTEM The SMARTS start here...
WELCOME! The Project Nursery Smart Baby Monitor System is your gateway to smart baby monitoring and voice control for your smart home. It’s easy to set up and easy to use—this guide takes you through the steps to get started. + SMART CAMERA + SMART SPEAKER Check out our setup videos For the Smart Camera For the Smart Speaker On your computer, go to http://bit.ly/2k9veoG or scan the QR code here. On your computer, go to http://bit.ly/2BIeOKN or scan the QR code here.
STEP 1: UNPACK Smart Baby WiFi Camera Plus accessories: (1) Power adapter (1) 10’ Power cable Smart Speaker Plus accessory: (1) Power adapter with attached cord (2) Mounting screws (1) Mounting template 3
STEP 2: PLACE THE CAMERA Position the camera Find a location for the camera that gives you the best view of your baby in his or her crib. Place the camera on a flat surface, like a dresser or shelf, or mount the camera to a wall using the keyhole slots on its bottom (see the mounting template included in this package). IMPORTANT: NEVER place the camera or cords of any kind inside the crib. NEVER place the camera or cords within reach of the baby.
Plug in the camera Plug one end of the included power cable into the DC In jack on the back of the camera. Plug the other end into the included power adapter. Then plug the adapter into an outlet or surge protector. The camera turns on automatically when you plug it in (the indicator light on its back panel turns solid red). IMPORTANT: Make sure you carefully remove the protective film covering the camera’s face and lens before you continue setup.
STEP 3: SET UP THE CAMERA AND APP Install the Camera App on your phone or tablet In the Google Play or Apple App Stores, search for “PROJECT NURSERY SMART CAMERA” and look for the icon shown here. Then download and install the App. Once the Project Nursery Smart Camera App has installed on your smartphone or tablet, press the icon to launch the App.
Camera list Pair the Project Nursery camera with the App Make sure the Project Nursery Smart Camera App is open on your phone or tablet. Also make sure that your phone or tablet is connected to your WiFi network. In the App’s home screen, press the Add camera button at the bottom of the screen. Add camera NOTE: Make sure your camera is on! If you haven’t already turned it on, press the Power button on the right side of the camera (the camera’s LED lights up).
STEP 3: SET UP THE CAMERA AND APP (continued) The App will ask you to press the SET button on the bottom of the camera and enter the name (WIFI SSID) and password of your WiFi network. Find the SET button on the bottom of your WiFi camera. Press it for one second (until the camera gives an audio signal). Enter the name (WIFI SSID) and password for your home WiFi network in the App.
Camera list Choose the camera from the home screen Nursery 2017/04/21 11:45AM Press the part of the home screen showing the camera you set up in order to choose this camera. Nursery HD 31°C 68ºF Snapshot Sound Add camera The Camera View screen is your gateway to total control of your WiFi camera from virtually anywhere. If you’re having trouble setting up your camera: See the connection troubleshooting section on page 16.
STEP 4: SET UP THE SPEAKER AND SPEAKER APP Install the Speaker App on your phone or tablet In the Google Play or Apple App Stores, search for “Project Nursery Smart Speaker” and look for the icon shown here. Then download and install the App. Speaker back Speaker front Plug in & turn on the speaker Plug one end of the power adapter with attached cord into the DC IN jack on the bottom of the speaker. Run the cord through the canal on the bottom and out the hole labeled DC IN on the back.
Launch the Project Nursery Smart Speaker App on your phone or tablet Press the Project Nursery Smart Speaker icon on your phone or tablet’s screen to launch it. Note: The first time you launch the Project Nursery App, it will ask to access your music and video libraries on your phone or tablet. To get the most from the Smart Speaker, we recommend you allow the Project Nursery App to access these libraries.
STEP 4: SET UP THE SPEAKER AND SPEAKER APP (continued) Speaker front Once you’ve entered the information for your WiFi network and chosen your speaker, press and hold the WIFI/BLUETOOTH button on the front of the speaker until the speaker announces “Connecting to your network...this may take 1 to 3 minutes.” Then release the button. Press the Next button in the App to proceed. The App is now connecting the speaker to your WiFi network. This might take a few minutes.
Now you’re ready to set up this speaker to work with Alexa through your Amazon account. Press the Sign in with Amazon button in the App. Then, choose your preferred language to use for Alexa and follow the instructions to continue. Once you’ve logged into your Amazon account, the App confirms your login and introduces you to Alexa. Press the Next button on both screens to proceed. Congratulations! You’ve just set up the Project Nursery Smart Speaker.
STEP 5: ACTIVATE THE PROJECT NURSERY ALEXA SKILL Install the Amazon Alexa App on your phone or tablet In the Google Play or Apple App Stores, search for “Amazon Alexa” and look for the icon shown here. Then download and install the App. Enable the Project Nursery Alexa skill In the Alexa App, search for “Project Nursery.” Then choose the Project Nursery skill from the results. In the next screen, press the ENABLE button.
Using Alexa (“Open Project Nursery” commands) Once you’ve enabled the Project Nursery Alexa Skill, you’re ready to start using Alexa with your Smart WiFi Baby Monitor system. To start controlling with Alexa: Say “Alexa, open Project Nursery.” Then use one of voice commands below. IMPORTANT: Use the name you gave your camera in the setup process—in the examples below the camera is named “Nursery.” Say... Sounds / Lullabies Snapshots/ Video *You must have an SD card (not included) in the camera to use these.
Connection Troubleshooting + Make sure your phone or tablet is connected to the WiFi network you want to use. + Make sure the camera is getting a good signal from your WiFi router. See step 3 for more information. + Test your WiFi network with other devices to make sure its working. + Double check that you’ve entered the correct password for your WiFi network in the Project Nursery App. + Make sure your router is broadcasting its SSID (name). The Project Nursery camera does not support hidden SSIDs.