Technical data

english
deutsch
francais
34
After setting-up, switch on all equipment. The projector can be controlled by the
keypad, by the remote control or using the RS232 or LAN interfaces. To switch the
projector on, firmly press the POWER button on the keypad or the remote control. The
STATUS indicator will turn from yellow to blue when the unit is switched on.
If the STATUS indicator is flashing yellow, please wait until it turns permanent yellow.
Issue the PIN code if activated.
When only one source is connected, the projector will auto-detect that source. If more
sources are connected, the projector will search for the next active source according to
the following list, provided that SOURCE SCAN is set to ON in the SET UP sub menu
(see description of menu system):
- VGA
- DVI-D
- YPbPr (Component)
- S-Video
- C-Video
Select between the sources by pressing the SRC buttons on the keypad or the direct
source selection keys on the remote control. Only sources that are active will be
displayed.
If no source is active, searching messages will appear on the screen. If no source is
active for a long time, the projector will go in standby mode if DPMS (power save) is set
to ON in the SET UP sub menu.
The STATUS indicator will turn from blue to flashing yellow, then yellow. The projector
will be switched back on if at least one source is (re)activated. The power-down
function can be disabled in the menu.
See DPMS in the SET UP sub menu.
To switch the projector off, firmly press the POWER button on the keypad or the
remote control twice (to confirm that you really want to switch off the unit). The STATUS
indicator will turn from blue to flashing yellow, then yellow when switched off. You may
not switch the unit on while the STATUS indicator is flashing yellow. Please wait until
the indicator is permanent yellow.
MOUSE EMULATION – PRESENTATION CONTROL
You may use the remote control arrow keys and LEFT and RIGHT buttons as a remote
mouse, controlling your presentations and for moving the mouse pointer around on the
screen. The arrow keys allow for limited mouse pointer control.
To activate the mouse control function, you need to connect the projector to the PC
via the USB port.
USING THE PROJECTOR
EINSATZ DES PROJEKTORS
UTILISATION DU PROJECTEUR
Nach der Einrichtung, müssen alle Geräte eingeschaltet werden. Der Projektor kann
über das Tastenfeld, die Fernbedienung oder die RS232- bzw. LAN-Schnittstellen
gesteuert werden. Zum Einschalten des Projektors, drücken Sie fest auf die Taste
STROMVERSORGUNG auf dem Tastenfeld oder der Fernbedienung. Die Anzeige
STATUS schaltet von Gelb auf Blau, sobald das Gerät angeschaltet ist.
Blinkt die Anzeige STATUS gelb, müssen Sie warten, bis sie kontinuierliche gelb leuchtet.
Geben Sie den PIN-Code ein, falls dieser aktiviert ist.
Ist nur eine Quelle angeschlossen, so erkennt der Projektor diese automatisch. Sind
mehrere Quellen angeschlossen, sucht der Projektor die folgende aktive Quelle nach
der nachstehenden Liste, vorausgesetzt die Option QUELLENSUCHE ist im Untermenü
SETUP eingestellt (siehe die Beschreibung des Menüsystems):
- VGA
- DVI-D
- YPbPr (Komponente)
- S-Video
- C-Video
Schalten Sie mit Hilfe der Taste SRC auf dem Tastenfeld bzw. der Fernbedienung
zwischen den verschiedenen Quellen um. Es werden nur aktive Quellen angezeigt.
Ist keine Quelle aktiv, so erscheinen auf dem Bildschirm Suchmeldungen. Ist längere Zeit
keine Quelle aktiv, schaltet der Projektor in den Standby-Betrieb um, vorausgesetzt die
Option DPMS (Stromsparbetrieb) ist im Untermenü SETUP auf EIN gestellt.
Die Anzeige STATUS schaltet von Blau auf blinkend Gelb und dann auf Gelb. Der
Projektor schaltet wieder zurück, wenn zumindest eine Quelle (erneut) aktiviert wird. Die
Abschaltefunktion kann im Menü deaktiviert werden.
Siehe DPMS im Untermenü SETUP.
Zum Ausschalten des Projektors, drücken Sie fest zwei Mal auf die Taste
STROMVERSORGUNG auf dem Tastenfeld oder der Fernbedienung (um zu bestätigen,
dass Sie das Gerät wirklich ausschalten möchten). Die Anzeige STATUS schaltet von
Blau auf blinkend Gelb und dann auf Gelb, wenn das Gerät ausgeschaltet wird. Das
Gerät kann nicht wieder eingeschaltet werden, solange die Anzeige STATUS gelb blinkt.
Warten Sie bitte, bis die Anzeige kontinuierlich gelb leuchtet.
MAUSEEMULATION – STEUERUNG VON PRÄSENTATIONEN
Mit Hilfe der Pfeiltasten auf der Fernbedienung und den Tasten RECHTS und LINKS als
Fernbedienungs-Maus kann die Präsentation gesteuert und der Mauszeiger auf dem
Bildschirm bewegt werden. Die Pfeiltasten ermöglichen aber nur eine eingeschränkte
Mauszeigersteuerung.
Um Die Maussteuerungsfunktion zu aktivieren, muss der Projektor mit dem PC über den
USB-Anschluss verbunden sein.
Après l’installation, allumez tout le système. Le projecteur peut être commandé par
le clavier, par la télécommande ou par les interfaces RS 232 ou LAN. Pour allumer le
projecteur, appuyez fermement sur le bouton POWER du clavier ou de la télécommande.
L’indicateur d’ETAT passe du jaune au bleu quand l’appareil est allumé.
Si l’indicateur d’ETAT clignote jaune, patientez jusqu’à ce qu’il devienne permanent.
Tapez le code PIN s’il est activé.
Quand une seule source est connectée, le projecteur détecte automatiquement cette
source. Si plusieurs sources sont connectées, le projecteur cherche la prochaine
source active selon la liste suivante, à condition que SOURCE SCAN soit sur ON dans
le sous-menu SET UP (voir la description du menu) :
- VGA
- DVI-D
- YPbPr (Composante)
- S-Vidéo
- C-Vidéo
Choisissez parmi les sources en appuyant sur les boutons SRC du clavier ou sur les
touches de sélection directe des sources sur la télécommande. Seules les sources
actives sont affichées.
Si aucune source n’est active, recherchez dans les messages qui apparaissent sur
l’écran. Si aucune source n’est active pendant longtemps, le projecteur se met en
mode veille si DPMS (économie d’énergie) est sur ON dans le sous-menu SET UP.
L’indicateur d’ETAT passe du bleu au clignotant jaune, puis au jaune permanent. Le
projecteur est rallumé si au moins une source est (ré) activée. La fonction hors-tension
peut être désactivée dans le menu.
Regardez DPMS dans le sous-menu SET UP.
Pour éteindre le projecteur, appuyez fermement deux fois (pour confirmer que
vous voulez vraiment éteindre l’appareil) sur le bouton POWER du clavier ou de la
télécommande. L’indicateur d‘ETAT passe du bleu au clignotant jaune, puis au jaune
quand il est éteint. Vous ne pouvez pas allumer l’appareil tant que l’indicateur d’ETAT
clignote jaune. Attendez que l’indicateur soit jaune permanent.
EMULATION DE LA SOURIS – CONTROLE DE LA PRESENTATION
Vous pouvez utiliser les touches flèche de la télécommande et les boutons GAUCHE
et DROITE comme une souris à distance, pour contrôler vos présentations et pour
déplacer le curseur de la souris sur l’écran. Les touches flèche tiennent compte du
contrôle limité du curseur de la souris.
Pour activer la fonction contrôle de la souris, vous devez connecter le projecteur au
PC par le port USB.
Downloaded From projector-manual.com Projectiondesign Manuals