LIGHT INTENSITY METER Users Manual
■. Introduction Thank you for purchasing the light intensity meter from us. Please take a few minutes to browse through this user manual before you begin to operate the meter to ensure that you are fully familiarized with how best to operate the meter as accurately and safely as possible. This meter is an illuminance measuring instrument. It is normally used to measure illuminances, e.g.at workplaces. 1.
. When the battery voltage is under proper operation requirement, the symbol will show on the LCD and the battery need to be replaced with new. 1.1.2 Maintaining the product Do not measure at a high temperature, high humidity places. Keep the light sensor clean. To guarantee correct readings: Hold the instrument horizontally so that the light sensor is directed upwards.
foot candle (lm/ft2) 3. Resolution: 1 Lux（0…90000 Lux）； 0.1 ftc（0…8300.0 ftc）； 4. Range: 0…90000 Lux 0…8300.0 ftc 5. Accuracy: 6. Sample rate: 1 time /sec 7. auto power off: about 20 minutes 8. low battery indicator 9. ±(3% +30 digits) to reference Operating environment: 0℃ ~ 50 ℃(32℉~122℉)，0 ~ 80%RH 10. Storage environment: -20℃ ~ 60℃(-4℉~140℉)，0 ~ 80%RH 11. Dimension and Weight: 121(L)x60(W)x30(H)mm, about 180g 12. Accessories: DC1.
■. Names of parts Instrument Familiarization 1. Sensor cover 2. Light sensor 3. LCD display 4. Function key Func.
The meaning of the symbols represented by the following table Number Symbol Functions of Order Indicating it is now in 1 the data-holding mode Indicating the display 2 value being the maximum value(MAX) Indicating the display 3 value being the minimum value(MIN) 4 Measure values 5 parameter unit 6 parameter unit Indication to the 7 calibration mode -5-
Indication low power of batteries. 8 Batteries should be replaced. ■. Operation instruction 1. Please install new batteries on the meter . 2. Put the meter on the environment to be measured and hold it horizontally so that the light sensor is directed upwards. 3. Press the ON/OFF key to turn the power on. 4. After power on, press the Unit key to select the needed units. 5. When the reading has been stable, read the illumination value.
■. Keys instruction 1. ON/OFF key Press the key to turn the power ON and press the key once more to turn the power OFF. 2. Func. key Press the key can select the state of MAX、MIN、 HOLD. The cycle of views shows as following figure: Mode key Measure mode Mode key Hold mode Max mode Min mode Mode key Mode key Hold mode: Reading are held. Max mode: Maximum values since the instrument was last switched on or last reset.
3. Unit key 1) Unit set Press the key can change the parameter unit: lux, ftc. 2) Back light contrl If press the key >2sec. the back light will be turned on, Press the key once >2sec. the light will be turned off. If the back light is not closed within 60 seconds, it will be turned off automatically. 3) Auto power off set When the meter is powered on, it is under auto power off mode. The meter will power itself off after 20 minutes if no key operation.
■.
Ward, Warehouse 100 ~ 200 Medical examination 300 ~ 750 room Operating room, 750 ~ 1,500 Emergency Room - School Hall, Indoor stadium, 200 ~ 750 Classroom Laboratory, Library 500 ~ 1,500 ■. Maintenance 1. CLEANING INSTRUCTIONS The meter may be wiped down with a wet sponge or cloth using a mild water based detergent or anti-bacterial soap and rinsed under a gentle stream of cold water. NOTE: This unit is not designed for complete submersion or washing in water. 2.
Use the following procedure: When the battery voltage drop below proper operation range the symbol will appear on the LCD display and the battery need to be replaced. Press the battery cover and towards arrowhead direction to open the battery cover. Replace the battery with three new 1.5V batteries (AAA). -11- WLS2110 Replace the battery cover.
