User guide

ManualsBrandsProkit's Industries ManualsToolsMT-7062

MT-7062 HDMI Cable Tester

User Manual

User’s Manual

1st Edition, 2013

Summary of content (24 pages)

PAGE 2
DESCRIPTION The Pro’sKit MT-7062 HDMI Cable Tester is designed for professional HDMI installations. This portable device allows installers to quickly test, troubleshoot, and verify HDMI (high definition multimedia interface) cables. MT-7062 is designed to test wire circuit state of HDMI cables with Type A & C connectors conforming to 1.0, 1.1, 1.2, 1.2a, 1.3, 1.3a, 1.3b, 1.3c, 1.4, 1.
PAGE 3
CONTENTS Your MT-7062 HDMI Cable Tester contains the following： 1. 1 x Master unit 2. 1 x Remote unit 3. 1 x Pouch bag. 4. Users’ Manual. FEATURES： The MT-7062 HDMI cable tester allows the fast and accurate verification both HDMI type A and Type C cables, mapping continuity and proper configuration and displays 19 pins and shield connection status on both master and remote unit.
PAGE 4
           Test interface of Remote unit：HDMI (type A) ×1pcs, Mini HDMI (type C) ×1 pcs. Cable length：Under 50 meters. Test Mode：Automatically fast scan、Automatically Slow scan、 Manual test for step by step. Displays：19 LEDs and shield LED on both master and remote unit. Beeper indication. Low battery indication：Under 6.
PAGE 5
HDMI Cable Wire / Pin And Signal Description： HDMI Mini-HDMI Pin Signal Description (A)Pin # (C) Pin # Assignment 1 2 3 4 2 1 3 5 Data 2﹢ Data 2S Data 2﹣ Data 1﹢ TMDS Red Data Plus (Data 2 +) TMDS Red Data Shield (Data 2 Shield) TMDS Red Data Minus (Data 2 –) TMDS Green Data Plus (Data 1 +) TMDS Green Data Shield (Data 1 Shield) TMDS Green Data Minus (Data 1 –) TMDS Blue Data Plus (Data 0+) TMDS Blue Data Shield (Data 0 Shield) TMDS Blue Data Minus (Data 0 –) TMDS Clock Plus (Clock +) TMDS Clock Shield (
PAGE 6
Power off： Slide upper left switch to “OFF”，”POWER” LED will go out and the unit will no longer work when pushing the “TEST” button. Master unit loop continuity scan testing function  ※ ※ Note When performing master unit scan test, sequence of LEDs light up as below.
PAGE 7
  Open：with a short “beep” sound。No connected pins LED are off. Example: Test HDMI (A Type) to HDMI (A Type) cable that pin #2, #5, #8 and #11 are not connected , or test HDMI (A Type) to Mini-HDMI (C Type) cable that pin #1、#4、#7、#10 are not connected. (Fig 3.) Short： With three short “beep” sound. Shorted pins LED will light up at same time. Example: Test HDMI (A Type) to HDMI (A Type) cable that pin #4、#5、#6 are shorted or test HDMI (A Type) to Mini-HDMI (C Type) cable that pin #4、#5、#6 are shorted.
PAGE 8
Fig 4. Short Fig 5. Crossover Master unit with Remote unit automatic testing function ※ Insert one of A type connector of cable to Master unit MAIN (A Type) socket and insert the other one to Remote unit A Type connector for test HDMI cable A type to A type. ※ Insert A type connector to Master unit LOOPBACK (A Type) and insert C type connector to Remote unit Mini-HDMI (C Type) for test HDMI cable A type to Mini-HDMI (C Type).
PAGE 9
2. 3. Press “ TEST” button then Master unit and Remote unit both #1~19 and “Shield” LEDs will indicate tested result. Testing result will keep 12 seconds then all LEDs are off except “POWER”LED for saving power. LED indicates test result as below:  Straight：Master unit and Remote unit both testing pin #1~19 and “Shield” LEDs are all lighted up. (Fig 6.)  Open：Master unit and Remote unit both no connected pins LEDs are off. (Fig 7.)  Short：Master unit testing short pin LEDs brighter than others.
PAGE 10
  Short：Master unit LED brighter than others and Remote unit LED off when scan to shorted pins, Master unit and Remote unit both LED are all lighted up in sequence, Example : Test HDMI (A Type) to HDMI (A Type) cable that pin #4、#5、#6 are shorted, or teat HDMI (A Type) to Mini-HDMI (C Type) cable that pin #4、#5、#6 are shorted, or test Mini-HDMI (C Type) to Mini-HDMI (C Type) cable that pin #4、#5、 #6 are shorted. (Fig 8.
PAGE 11
Fig 7. Open Fig 8.
PAGE 12
Fig 9. Crossover Master unit with Remote unit fast continuity scan testing function： 1. Press “ TEST” button during the slow continuity scan testing, or press three times“ TEST” button after the automatic testing LEDs are off：It will fast scan pin 1~19pin and Shield，Master unit and Remote unit both #1~19 and Shield LEDs will light up in sequence fast and sustained repeated automatic scan. 2. The test result please refer to the slow continuity scan testing function. (Fig 6. ~ Fig 9.
PAGE 13
BATTERY LIFE AND REPLACEMENT：   Caution To avoid unreliable test results, replace the battery as soon as the low battery indication appears. Warnings To avoid possible electric shock or personal injury, turn off the master unit and disconnect all test leads before replacing the battery. Battery Status：When ”POWER/LOW BATT.” LED is flashing on the master unit, it means the battery voltage is under 6.0V which couldn’t power the device on. Please replace the battery as the following step： 1.
PAGE 14
         警告不要連接這測試器在具有活電的電路上，因為它有可能損害這設備。在充電的HDMI電纜線上，使用本測試器，容易造成測試器損害。注意在操作測試器前，請詳閱本說明書。如未遵守相關規定，可導致測試器損害或危及使用者。不要跌落或浸濕這測試器。不要讓這測試器暴露在潮濕的環境中或讓烈日直接照射。不要試圖打開測試器外殼或移除零件，這樣做可能導致測試器損壞和危及使用者。維修和保養，必須交由熟知危險的專業維修人員或具備資格的電氣工程師/技術員進行。遵循任何貿易組織或監管機構的建議，其範圍包含使用這測試器或對於使用者的傷害。當長時間或超過一個月不使用本測試器，應將電池取出，避免電池化學液滲漏，損壞本測試器。請使用同規格的電池，否則可能損壞本設備。包裝內容：你的MT-7062 HDMI 測試器，包裝內容如下：  主機 1台.  遠端器 1個.  攜存袋 1個.  使用手冊 1本.
PAGE 15
主機自我迴路測試具有主機自我迴路測試的設計，只有主機.不必遠端器，就可以測試A 對A、A對C接口的HDMI電纜線。 3種測試模式  具有自動快速掃描功能，可以測試電纜線中，所有芯線導體連通狀態。  具有自動慢速掃描功能，可以測試電纜線中，所有芯線導體連通狀態。  具有手動測試功能，可以單步間歇的偵測電纜線中，個別芯線導體的故障狀態。 HDMI電纜線連通測試自動檢測HDMI電纜線內，19條訊號和屏蔽芯線導體的直通、短路、斷路、交叉…等狀態。故障檢修適合快速檢修和查證HDTV安裝，和DIY製作HDMI連接線。產品規格：              電纜測試：適用於具有A和C接口，符合 1.0, 1.1, 1.2, 1.2a, 1.3, 1.3a, 1.3b, 1.3c, 1.4, 1.
PAGE 16
產品外觀圖： 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 主機迴路接口： Mini-HDMI (C Type) (這個接口，當與遠端器搭配測試Mini-HDMI (C Type)對Mini-HDMI (C Type)線時，也做為主機接口。) 主機主要接口：HDMI (A Type) 主機迴路接口：HDMI (A Type) 遠端器接口：HDMI (A Type) (圖 1.
PAGE 17
7 8 Data 0﹢ 8 7 Data 0S 9 9 Data 0﹣ 10 11 Clock ﹢ 11 10 Clock S 12 12 Clock ﹣ 13 14 CEC 14 15 16 17 15 16 Uti./Res.
PAGE 18
主機自我迴路連續快速掃瞄測試：  ※ ※ 1. 2. 3.
PAGE 19
圖 2. 導通圖 3. 斷路圖 4. 短路圖 5.
PAGE 20
主機+遠端自動測試： ※ 測試HDMI (A Type)對HDMI (A Type)的線時：將線插入主機 MAIN (A Type)接口和遠端器HDMI (A Type)接口。 ※ 測試HDMI (A Type)對Mini-HDMI (C Type)的線時：將線插入主機MAIN (A Type)接口和遠端器Mini-HDMI (C Type)接口。 ※ 測試Mini-HDMI (C Type)對Mini-HDMI (C Type)的線時：將線插入主機Mini-HDMI (C Type)接口和遠端器Mini-HDMI (C Type) 接口。 1. 主機左上角開關，撥到REMOTE檔位時，POWER燈號點亮，主機1~19pin＋Shield燈號先全部顯示，並“滴”一聲長音後，接續主機與遠端器的兩組1~19pin＋Shield燈號顯示測試結果，測試結果持續12秒鐘，主機與遠端器的兩組pin燈號會自動熄滅，進入省電模式，只有POWER燈號持續亮。 2. 按一下TEST鍵，主機與遠端器的兩組1~19pin＋Shield燈號會再顯示測試結果，測試結果持續12秒鐘，依此反覆… 3.
PAGE 21
 斷路：主機和遠端器斷路對應的 pin 燈號都不亮，其它 pin 燈號從 1~19~S 依順序點亮。如 HDMI (A Type)對 HDMI (A Type)線的#2、#5、#8、#11 斷路或 HDMI (A Type)對 Mini-HDMI (C Type)線的#1、#4、#7、#10 斷路或 Mini-HDMI (C Type)對 Mini-HDMI (C Type)線的#1、#4、#7、#10 斷路。 (圖 7.)  短路：主機短路的 pin 燈號，會比其他 pin 燈號更亮，遠端器短路的 pin 燈號不亮，主機和遠端器其它 pin 燈號從 1~19~S 依順序點亮。如 HDMI (A Type)對 HDMI (A Type) 線的#4、#5、#6 短路或 HDMI (A Type)對 Mini-HDMI (C Type) 線的#4、#5、#6 短路或 Mini-HDMI (C Type)對 Mini-HDMI (C Type)線的#4、#5、#6 短路。(圖 8.
PAGE 22
圖 7. 斷路圖 8.
PAGE 23
圖 9. 交叉主機+遠端快速連續掃描測試： 1. 遠端慢速自動掃描進行時，再按一下TEST鍵(或是遠端快速結果顯示的pin燈號熄滅後，連按三下TEST鍵)是：「主機+ 遠端快速連續掃描測試」：快速自動掃描1~19pin＋Shield，並持續反覆快速自動掃描。 2. 「主機+遠端快速連續掃描測試」，結果顯示：主機與遠端器的pin燈號，會從1~19~S依順序點亮：燈號顯示與「主機+ 遠端慢速連續掃描測試」相同。(圖 6.~ 圖 9.) 主機+遠端手動單步測試： 1. 長按3秒是：「主機+遠端手動單步測試」：按一下測試 1pin… 依此類推1~19pin＋Shield，並持續反覆手動測試。 2. 「主機+遠端手動單步測試」，結果顯示：每按TEST鍵一下，主機與遠端器會顯示1個pin燈號，並依序從1~19~S逐一點亮：燈號顯示與「主機+遠端慢速連續掃描測試」相同。(圖 6.~ 圖 9.) 3.
PAGE 24
電池壽命與更換：  小心為避免資料測試不可靠，一但出現電池低電壓指示時，請立即更換新電池。.  警告更換電池前，為避免觸電或人身傷害，請關閉主機，並斷開所有測試導線。電池狀態：當主機上的”POWER/LOW BATT.”的LED燈閃爍時，代表電池的電壓已低於6.0V。請依照下列指示，更換電池︰ 1. 更換電池前，請關閉主機，並斷開所有測試導線。 2. 打開主機背面的電池蓋，並正確的裝上新電池。 3. 僅可以使用1個DC 9V(NEAD 1604/6F22)的電池。 HDMI® 註冊商標屬於 HDMI Licensing, LLC.