User Manual

ManualsBrandsProkit's Industries ManualsPower ToolsPT-1201

PT-1201

Cordless Drill Driver 12V

User’s Manual

Edition

2012

PT-1201 User’s Manual

www.prokits.com.tw 1

Please read this handbook carefully before using the tool

General Safety Rules

WARNING Read all safety warnings and all instructions Failure to follow all

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference

The term “power tool” in the warnings refer to your mains operated (corded)

power tool or battery operated (cordless) power tool.

1) Work area

a) Keep work area clean and well lit. Cluttered and dark areas invite

accidents.

b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the

Summary of content (10 pages)

PAGE 1
PT-1201 User’s Manual Please read this handbook carefully before using the tool General Safety Rules PT-1201 WARNING Read all safety warnings and all instructions Failure to follow all warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference The term “power tool” in the warnings refer to your mains operated (corded) power tool or battery operated (cordless) power tool. 1) Work area a) Keep work area clean and well lit.
PAGE 2
PT-1201 User’s Manual risk of electric shock. f) If operating a power tools in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
PAGE 3
PT-1201 User’s Manual eyes, additionally seek medical help. Liquid ejected form the battery may cause irritation or burns. 6) Service Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. PT-1201 User’s Manual immediately with plenty of water. If these substances make contact with the eyes, rinse with plenty of water and visit a doctor immediately.
PAGE 4
PT-1201 User’s Manual Complied with EN60335-2-29 Indoor operation only .Accessory Screwdriver bits Bit size 15PCS PT-1201 User’s Manual resistance. The battery must be inserted completely until the battery retention clips on the sides of the battery compartment automatically lock it into place. To remove the battery press the battery retention clips and pulls the battery out of its compartment. Charging the Battery 6PCS drills: Φ1.5/ 2.
PAGE 5
PT-1201 User’s Manual forward and reverse switch in the central position before you put the machine down, to avoid unintentional starting. Torque adjustment You can control the maximum torque applied to the drill bit with the torque control knob. Attention! The torque control knob should only be operated when the machine is not running; otherwise the machine may be damaged.
PAGE 6
PT-1201 User’s Manual PT-1201 User’s Manual Maintenance and Clean Attention! Always remove the battery before carrying out any work on the machine. To clean, always use a dry or moist, but not wet, towel. Many cleaning agents contain chemical substances which may cause damage to the plastic parts of the machine. Therefore do not use any strong or inflammable cleaners such as petrol, paint thinner, turpentine or similar cleaning agents.
PAGE 7
PT-1201 User’s Manual PT-1201 User’s Manual 請在使用工具之前務必細心閱讀操作手冊 d) 啟動前務必移除調整電動工具使用的鑰匙或扳手，因其旋轉時可能導致一般的安全規則 e) 不要將手伸得過長，使用時保持適當距離與適當的平衡，如此較能控制警告：請詳細閱讀以下所有指示說明，如不遵循下面所有指示，也許會有觸電及火災等嚴重傷害。 f) 穿著適宜，不要穿寬鬆衣服或佩戴首飾。讓您的頭髮，衣服和手套遠離人身傷害. 些裝置可減少粉塵. a) 保持工作環境整潔，混亂的環境將帶來事故. b) 避免在可能發生爆炸的環境下使用電動工具，諸如在易燃的液體周圍，氣體或者粉塵環境中，電動工具可能製造點燃火花。 c) 使用電動工具時請使孩子和旁觀者遠離，因為分心可能使你失去對電動工具的控制 e) f) 3) 使用沒有任何接地的電源插座。非修改的插頭和電源插座將減少電擊的風險。防止身體接觸接地物表面（如水管、散熱器、冰箱等），如果你的身體接地，可能有損壞的風險。避免讓電動螺絲批暴露在雨中或是潮濕的環境中.
PAGE 8
PT-1201 User’s Manual d) 在惡劣環境下，電池裏的液體可能會滲出，請勿接觸。如果發生意外接 PT-1201 User’s Manual 產品規格 PT-1201A PT-1201F DC 12V One Gear Speed: 0-550rpm Φ0.8 ~ 10mm DC 12V One Gear Speed: 0-550rpm Φ0.8 ~ 10mm 鐵: Ø 6 mm 鐵: Ø 6 mm 混泥土: Ø 8 mm 混泥土: Ø 8 mm 木頭: Ø10 mm 木頭: Ø10 mm 16 +1Position 16 +1Position 型號觸，用清水沖洗。如果眼睛接觸液體，請立即就醫。額定電壓 6) 服務本電動工具的維修或更換零件需專業維修人員服務。這將確保電動工具的安全性無負載轉速鑽頭範圍關於充電起子的特別安全公告當電鑽鑽進牆體內之前，請用金屬探測器檢查一下，避免在鑽取時踫到電源線、天然氣管道及水管.
PAGE 9
配件 PT-1201 User’s Manual 15PCS 批頭 6PCS drills: Φ1.5/ 2.5/ 3/ 4/ 5/ 6 mm 1PC extension: 60mm (L) 6PCS: PH1 ; PH2; PZ1 ; PZ2 ;SL 5 ;SL 6mm (L : 25mm) 1PC : SL6-PH2 (L : 45mm) 1PC : SL5-PH1 (L : 45mm) 批頭規格產品功能啟動開關壓下啟動開關電批即可開始工作，並保持一直壓下狀態電批可連續工作。若鬆開，電批即停止運轉正反轉切換重要！在電批完全停止才可以使用正反轉切換開關，否則可能會損壞機器。使用正反轉切換開關是使電批朝順時針方向和逆時針旋轉。當正反快關置於中間時，電批被鎖定，不能旋轉，可避免意外啟動。扭力調節您可以通過扭力杯調節扭力.
PAGE 10
重要! 在鑽孔開始時選擇一個較低的速度，以免偏離鑽孔位置。如果孔比較深，鑽頭可能會卡在孔裏。在這種情況下使用高扭矩可能會損壞鑽頭或電鑽。如果鑽頭被卡住，請牢牢握住電鑽，並立即釋放啟動開關，並切換正反轉按鈕，使用低轉速以取出卡住的鑽頭。 PT-1201 User’s Manual 4. 在塑膠上鑽孔參見在木頭上鑽孔的方法. 5. 在石頭磚塊或類似的物體上鑽孔參見在金屬上鑽孔的方法 6. 將電鑽做電批使用使用電批前檢查是否螺絲位是正確插入。避免過度緊固螺絲，否則可能會損壞螺絲頭 7. 螺絲插入設置順時針旋轉方向，將螺釘放入電批批頭，請垂直於螺絲頭，否則螺絲或螺絲頭可能會被損壞。按住螺絲批下壓。當螺絲完全擰入，釋放啟動按鈕，若不立即釋放，否則螺絲或螺絲頭可能會被損壞。如果啟動按鈕不立即釋放在使用高扭矩也可能損壞鑽頭或電鑽。 8.