PT-1441 Cordless Drill Driver 14.4V User’s Manual 1st Edition, 2013 ©2013 Copyright by Prokit’s Industrial Co., Ltd.
PT-1441 User’s Manual Please read this handbook carefully before using the tool General Safety Rules WARNING Read all safety warnings and all instructions Failure to follow all warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference The term “power tool” in the warnings refers to your mains operated (corded) power tool or battery operated (cordless) power tool. 1) Work area a) Keep work area clean and well lit.
PT-1441 User’s Manual Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewelry.
PT-1441 User’s Manual d) Under abusive conditions, liquid may be ejected from the battery; avoid to contact the liquid. If contact accidentally, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. e) To ensure the maximum battery life and optima performance, always charge the battery before use. f) Please check if the tools still have power when not in use for a long time.
PT-1441 User’s Manual If any person comes into contact with acid or similar internal fluids or substances contained in the battery, wash off these substances immediately with plenty of water. If these substances make contact with the eyes, rinse with plenty of water and visit a doctor immediately. Do not place the rechargeable battery into fire or water. It can explode. The Rechargeable Battery should not be discarded to domestic refuse, regardless of whether used or unused.
PT-1441 User’s Manual Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
PT-1441 User’s Manual Important! Only use the provided battery charger for charging the battery. First place the rechargeable battery into the charging slot in the charger and then connect the charger to the mains. Charging starts automatically. Remove the battery from the charge after about 5 hours. Always disconnect the charger from the mains before you remove the battery from the charger.
PT-1441 User’s Manual particular wooden work-pieces) or to the screw. For drilling select a higher torque setting. Do a test first on an item which is not your final work-piece and adjust the desired torque accordingly before you start the actual work. Operation for working Only use tool bits which can be securely fastened in the chuck and for which the drill has been designed. 1. Drilling Check whether the drill bit is correctly inserted and tightly fastened before you start the machine.
PT-1441 User’s Manual 7. Screw Insertion Set the direction of rotation of the drill to the clockwise direction. Insert the screw-bit into the slot in the head of the screw. Hold the screw bit perpendicular to the head of the screw, otherwise the screw or the screw head may be damaged. Press the screw bit against the screw with a constant pressure while driving in the screw.
PT-1441 User’s Manual PT-1441 14.4V1000mAH 充電起子 使用前請先詳讀本份操作手冊 基本安全規則 警告:沒有按照以下安全注意事項及使用說明操作,將導致觸電、火災或其它嚴重傷害。 請將本份文件加以保存以供日後所須參考使用。 1. 工作區域 a) 請保持工作環境整潔明亮,混亂昏暗的環境將引發事故。 b) 請不要在易爆環境中使用電動工具,例如在易燃的液體、瓦斯或者粉塵環境中。電動工具使用 時所產生的火花可能點燃粉塵或氣體。 c) 工作環境中請勿有孩童及旁觀者,以免分心造成失誤。 2. 電器安全 a) 電動工具插頭請與相配的插座使用。請不要以任何方式拆解並改裝插頭,需接地的電動工具 不可使用轉接插頭。使用未拆解過的插頭和匹配的插座將減少觸電的風險。 b) 請避免讓人體接觸接地表面,像是管道、散熱器、爐灶及冰箱等,如果你的身體接地將會有觸 電的風險。 c) 請避免讓電動工具暴露在雨中或是潮濕的環境中.
PT-1441 User’s Manual 4. 電動工具的使用及維護 a 請選擇適當的電動工具。請依據您的工作狀況使用正確的電動工具,可使工作更有效率、更 安全,並使電動工具發揮最大效益。 b 當電動工具的啟動開關不能開啟或關閉電源時請停止使用,請送回原廠修理以免發生危險。 c 當電動工具要進行調整、更換配件或儲存不用時,請先將插頭拔下或將電池盒拆除,此舉可 降低電動工具意外啟動的風險。 d 電動工具請貯存在兒童無法接觸的地方。請不要讓不熟悉或對操作說明不瞭解的人員使用。 未經訓練的人員操作電動工具會造成危險。 e 電動工具維護:請檢查電動工具可調的部位是否到位,零件是否有破損或是有其它任何可能 影響電動工具操作的情形。如有損壞,請先進行修理後才能使用。許多事故都是因為電動工 具未作好維護而造成的。.
PT-1441 User’s Manual 受到壓力或任何其他形式的機械應力。電池須遠離極熱和極冷的環境。請勿試圖修復電池或充電 器。如果任何部件有缺陷,請由合格的維修技術人員維修或送回原廠維修。電池充電的環境溫度為 10℃到40℃之間,已充電的電池可以在0℃到50℃環境溫度下提供電動工具電力進行作業。如不使 用時,請將電池儲存在10℃到30℃之間的乾燥環境。 重要! 危險! 請勿讓電池短路或接觸水氣。請勿將電池與金屬物品存放在一起以免造成短路, 電池將產生過熱、發燙或爆炸。 如果任何人接觸到電池內部液體或物質,請立即用大量清水沖洗。如果這些物質接觸眼睛,請立即 用清水沖洗後立刻就醫。 請勿將將充電電池放入水中或火中,以免發生爆炸。無論充電電池是否使用,均不可當作家用垃圾 丟棄。您應該按照電池回收條例送到當地國家的電池回收站或是交回給我們並標示為“使用過電 池"。 規格 型號 額定電壓 無負載轉速 鑽頭規格範圍 PT-1441A DC 14.4V 0-550rpm Φ0.8 ~ 10mm 鋼鐵: Ø 6 mm 水泥: Ø 8 mm 鑽頭應用 木頭: Ø10 mm 扭力設定 21 +1檔 輸出扭力 7 N.
PT-1441 User’s Manual 配件 批頭 批頭規格 其他配件 : 14 PCS 6PCS 鑽頭: Φ1.5/ 2.5/ 3/ 4/ 5/ 6 mm 6PCS 25mm 批頭 : PH1 ; PH2 ; PZ1 ; PZ2 ;SL 5 ; SL 6 1PC 60mm 延長桿 1PCS 45mm:雙頭披頭 SL6-PH2 變壓器、充電座及攜帶盒 環境保護 廢棄的電器產品請勿當作家用垃圾處理。 請依當地國家的回收條例送到回收站或是零售商進行回收。 產品功能 扭力杯 啟動開關 正反轉開關 充電座 電池釋放按鈕 www.prokits.com.
PT-1441 User’s Manual 操作說明 基本說明 電池安裝 請將可充電電池對準電動工具本體, 無須過度施力即可輕易推入,推入後本體的電池釋放按鈕會 卡住電池不脫落,移除時按下電池釋放按鈕後拉出電池即可。 充電 首次使用前請先將可充電電池充飽電。每次電池完整放電後才能再次進行充電,以避免電池效率降 低。除此之外還會造成之後每次充電都無法充飽電的情況發生。 重要! 請使用本公司提供的電池充電器。首先請取下可充電電池放入充電座內,再連接充電電 源,充電器會自動開始充電。充電5小時後請先將充電座電源移除再取下電池。 批頭 / 鑽頭安裝 本產品有自動夾頭設計,不需額外的工具進行固定。請旋轉前端夾頭環直到夾頭鬆開, 將批頭或鑽 頭放入後以順時針方向旋轉夾頭環鎖緊,鎖緊後請確認批頭或鑽頭沒有歪斜。若要取出則將夾頭環 以逆時針方向旋轉直到夾頭鬆開後,移除批頭或鑽頭。 重要! 當您在安裝批頭或鑽頭前請先將電池移除,以避免意外啟動。 啟動開關 本產品為無段變速設計,壓下啟動開關後即可運轉,轉速快慢可藉由啟動開關的輕重按壓來控制, 按壓較重時則轉速會變快,反之則變慢,鬆開啟動開關後即停止運轉。 正反轉切換 當正反轉
PT-1441 User’s Manual 操作使用 請使用合格的批頭產品, 并確認規格符合本產品的裝配尺寸. 1. 鑽孔 在開始操作前請先檢查鑽頭是否已正確插入且牢靠不晃動。使用適當鋒利的鑽頭。不使用已磨損 的批頭。鑽頭開始使用時請先調到低轉速。當有較大的洞需鑽時,請先用小鑽頭先鑚,再使用適 合的鑽頭將洞加大。 2. 在木頭上鑽孔 鑚木頭請選用搭配的鑽木鑽頭,將工件使用適當的夾具固定保護,在欲鑚孔的位置用鋒利的工具 或釘子作記號,鑽孔時請勿讓機器對工件施與過度的壓力。 3. 在金屬上鑽孔 在金屬上鑽孔時請選用搭配的鑽金屬鑽頭,鑽孔時請一直保持使用冷卻液,將工件使用適當的夾 具固定保護,工件須緊貼平放在工作臺上,在欲鑚孔的中心以戳刺的方式作記號,請勿讓機器對 工件施與過度的壓力,並請維持正常的速度鑽孔。 重要! 在鑽孔開始時請先選擇較低轉速以避免鑽頭滑脫偏離鑽孔位置。如果要鑽的洞孔比較 深,鑽頭可能會因此卡在洞孔內。在這種情況下使用高扭矩可能會損壞鑽頭或電鑽。如果鑽頭 被卡住,請牢牢握住電鑽,將正反轉切換向右推(逆時針方向),調整到較低的扭力,立即按壓啟 動開關,使用低轉速較容易取出卡住的鑽頭。 4.
PT-1441 User’s Manual 維護和清潔 特別注意! 在對本機進行任何作業前請先取下電池。 請使用乾的或是微濕的毛巾進行清潔。許多清潔劑含有化學物質,可能會使機器的塑膠部位造成損 壞。因此請勿使用其它較強烈或易燃的清洗劑像是汽油、松香水,松節油及其它類似的清潔劑。本 機通風孔請防止灰塵沉積以免過熱。 服務 更多關於 PT-1441A / PT-1441F 的資訊及其它產品, 請上本公司網站 www.prokits.com.tw Certificate Number: TW98/12323QA ©2013 Copy Right by Prokit’s Industrial Co., Ltd. 2013001(C) www.prokits.com.