TABLE OF CONTENTS
Thank you to choose the LED backlight LCD TV made by our company, a valuable product with excellent quality and multiple functions. This machine will bring you more audiovisual enjoyment. Its design can insure user's safety. All machine are strictly tested before leaving factory. But incorrect use can lead to electric shock or fire. In order to insure safety and extend its life, please read below regulations carefully before using it and comply with the following safety instructions.
thing to knock, press, score the panel. Otherwise it will be harmful for the panel. The exchange cost is very high. 14) There is high voltage inside the machine but no parts which can be repaired by users themselves. In order to assure the people's safety, please don't open the case to repair it by yourself. If it is needed to repair, please contact qualified engineer to repair. 15) All cables can be connected or pull out only after power supply is turned off.
3
● interface specification: Specification Interface VGA HDMI DB-15, 75Ω 0.5~0.7Vp-p H/V:TTL Level (Support mode refer to VGA Input Mode ) Video signal: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i Audio: LPCM 48KHz, 44.1KHz, 32KHz, 24Bit, 20Bit, 16Bit CVBS Input/Output 75Ω 1Vp-p (PAL/NTSC/SECAM) S-VIDEO Input Y: 75Ω 1Vp-p; C: 75Ω 0.286Vp-p YCbCr/Ypbpr Y: 75Ω 1Vp-p; Cb/Cr: 75Ω 0.7Vp-p Signal mode: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i Audio Input/Output 20KΩ, 0.
● The Technical Specifications for Final Product Panel size 21.5" Max. Resolution 1920×1080 Best resolution 1920×1080@60Hz Pixel pitch 0.25mm×0.25mm Active area 476.64mm×268.11mm Power adapter 100-240V 60/50Hz Volume 3W+3W TV receive system PAL+NTSC/PAL+SECAM Unpacking Dimension(L×H×W) 535×394×36 mm Packing Dimension(L×H×W) 595×445×100 mm Net weight 5.0Kg Gross weight 6.0Kg Color 16.
● VGA input mode 21.
● Power supply: Comply with EPA standard,compatible with VESA DPMS standard. Power LED indicator Power consumption On Off Standby On ≤35W ≤1W Mode Note: This specification is subject to change without notices. If there are differences between manual and real operation, please do according to real operation.
Power Connection Insert the power plug into the socket of the electrical source (AC 100V-240V, 60/50Hz). Notes: 1. When connecting the power cord, be sure to turn off the machine and other equipment's power. 2. If a long time at leisure, please disconnect it from power supply.
Antenna Connection It is better to use outdoor antenna or CATV cable if you want to watch the colorful and hi-definition pictures. Attention: Please turn off TV power before the outdoor antenna is connected to the TV signal input port. Outdoor antenna can't be located near the high-voltage wires. Please pull out the plug of outdoor antenna to avoid thunder shock in thunder weather.
Computer Connection Please connect one end of VGA cord with the output port of the computer (available for both desktop or laptop computer), and another end of VGA cord with the input port of the VGA on its rear cover. Audio/Video machine with HDMI interfaces HDMI digital port Connection Connect external HDMI high signal source to HDMI digital input port of this machine through HDMI digital connector cable; push "SOURCE" button to select "HDMI" signal source.
AV1 Video Signal Connection Through composite cable, connect AV equipment VIDEO output termination to this machine VIDEO input, and AV equipment AUDIO output termination to this machine AUDIO input, respectively; Press "SOURCE" key to select "AV1" signal source.
AV-OUT Connection If you need watch image of DV and connect your TV game machine, you can connect audio or video output end of DV and game machine to the monitor. CVBS, DVD Player or other machine with CVBS/S-Video.
YPbPr/YCbCr Input Connection If the signal source is DVD, Digital wired receiver or equipments with the YPbPr/YCbCr output, recommends you to connect YPbPr or YCbCr output with the TV YPbPr/YCbCr input. In order to obtains the better picture quality, at the same time, please connect its audio output with TV audio input as shown in the following chart. If you choose the YPbPr/YCbCr signal, please set signal source selection under YPbPr pattern. CVBS, DVD Player or other machine with YPbPr/YCbCr.
Base installation Base equipment act as the picture. Equip the base with the machine according to arrow point, and lock the bolt tightly. Wall Mounting Stand Wall Mounting Board Wall Mounting subassembly installation Installation for VESA Wall Mounting 1. Take off the base. 2. Fasten the wall mounting board. ( The height can be confirmed by the user). 3. Fasten the wall mounting stand at the position of VESA on the rear cover with bolts. 4.
4 5 6 7 1 2 3 8 3 1. Remote Receiving Sensor. 2. Power Indicator. 3. Power switch. 4. SOURCE: Press this key to enter the menu of signal source and choose signal source. 5. CH+/CH-: Press these two keys to choose channel, and adjust the options you need under OSD operation. 6. VOL+/VOL-: Press these two keys to add or reduce volume, and adjust the analog value under OSD operation. 7. MENU: Press this key to enter main menu. 8. Power on/Standby .
POWER MUTE Power Mute Numerical key F1 Program list Key POWER MUTE Numerical key F1 Program list SMART S Function Turn on or standby Eliminate sound Number input button Freeze picture Look through or edit Program list Intelligent sound mode selection SMART P Intelligent image mode selection Cursor key Up or Down cursor button: function select Left or right cursor button; analog add or reduce Sound volume add or reduce button Press this button to display menu Press this button to display signal s
Remote control battery installation method: Take off the cover of battery box, fix two AAA batteries with 1.5 volt, and conform with the polarity of remote control battery box. Note: Appearance of the remote control may be different from this picture, please according to practicality. Precautions for use of remote control: 1. When using remote control you should point it to the remote-control inductive window. The goods between remote control and inductive window may hinder normal operation. 2.
TV AV 1 AV 2 SVIDEO YPbPr HDMI1 HDMI2 PC USB 18
PICTURE 50 50 50 50 50 CONTRAST BRIGHTNESS HUE S AT U R AT I O N SHARPNESS PICTURE MODE SCALE COLOR TONE 3D NR SEL S TA N D A R D FULL NORMAL MIDDLE ADJ MENU EXIT
★Special Attention 1. The Hue function is available only for NTSC system. 2. The value adjusted by user, such as Contrast, Brightness, Saturation, Hue, and Sharpness will be saved automatically by the machine as personal mode. ★Remote Control Shortcut Keys SMART P: Press SMART P key on the remote control. You can switch the function among the "STANDARD", "DYNAMIC", "SOFT", "PERSONAL" four modes.
SOUND Select to enter the SOUND submenu. Press "Up/Down" key on the remote control or the key "CH+/CH-" on the front panel to choose what you need. Press the "Left / Right" key on the remote control or the "VOL+/VOL-" key on the front panel to adjust analog value or state (see below table). ★Special Attention 1. Normally, 50 value of adjustment is recommended; 2.
OSD Select to enter the OSD submenu. Press "Up/Down" key on the remote control or "CH+/CH-" key on the front panel to choose what you need. Press the "Left/Right" key on the remote control or the "VOL+/VOL-" key on the front panel to adjust analog value or state (see below table).
ADVANCE Select to enter the ADVANCE submenu. Press "Up/Down" key on the remote control or "CH+/CH-" key on the front panel to choose what you need. Press the "Left/Right" key on the remote control or the"VOL+/VOL-" key on the front panel to adjust analog value or state (see below table). A D VA N C E SLEEP - TIMER DCC BLUE SCREEN RESETTING SEL Option Function OFF OFF ON ADJ MENU EXIT Description SLEEP - TIMER Set sleep time of the machine "Off, 15M, 30M, 45M, 60M, 120M", unit: minute.
TV Select to enter the TV submenu. Press "Up/Down" key on the remote control or "CH+/CH-" key on the front panel to choose what you need. Press the "Left/Right" key on the remote control or the "VOL+/VOL-" key on the front panel to adjust analog value or state (see below table). T V SEL Option Function AUTO M MONO OFF COLOR SYSTEM SOUND SYSTEM MTS SKIP AUTO SCAN MANUAL SEARCH FINE TUNING CHANNEL EDIT ADJ MENU Description COLOR SYSTEM Select color system "PAL, NTSC, AUTO" three modes.
AUTO SCAN Select to enter the submenu of TV. Then press ''Up/Down'' key CH 5 3 . 0 0 MHZ 2 on the remote control or ''CH+/CH-'' on the front panel to select ''AUTO SCAN''. The machine perform search after pressing ''Right'' key on the remote control or ''VOL+''on the front panel. (In the process of searching the channel automatically, press the key of ''MENU'' on the remote control to stop searching). Meanwhile, it will show Current Channel, Frequency. All of the TV programs will be saved automatically.
to select ''CHANNEL EDIT ''. Press ''Right'' key on the remote control to enter submenu of ''CHANNEL EDIT '' (Press program list key on the remote control to enter submenu of ''CHANNEL EDIT ''). NAME: Press ''Cursor'' key on the remote control to select channel. Press ''1'' key on the remote control to name. Press ''UP/Down'' key on the remote Control to select letter or number.
Select Channels with Numeric Keys 1. Operations to select channels with 1 digit (0-9): Press the number keys (0-9)on the remote control to select TV channel directly . 2. Operations to select channels with 2 digits (10-99): Press the number keys with 2 digits (10-99) on the remote control to select TV channels. 3. Operations to select channels with 3 digits (100-199): Press the number keys with 3 digits (100-199) on the remote control to select TV channels.
Symptom Factor Solution Snowflake speckle and sound noise. 1.Antenna cable connector is loose, cable is damaged. 2.Channel setting is incorrect. 3.Antenna cable type is not matching. 4.Direction or position of antenna cable is incorrect. 5.Signal is weak. 1.Check the antenna cable connector plug whether or not loose, cable whether or not perfect. 2.Refer to channel setting method, resetting again. 3.Check antenna cable type(VHF/UHF) 4.Adjust direction or position of antenna cable . 5.
Symptom Computer no display, and prompt no signal input, red indicator LED twinkling. Remote control distance is short, lose control. Computer display faintly. Factor Solution Signal cable is loose or fall off. 1.Receive window of remote continue was covered by objects. 2.The battery energy of remote control is to low. 1.Adjustment is incorrect. 2.Display mode is incorrect. Check signal cable whether or not loose, fall off, reconnect well again. 1.
30
