Lite Garage Vacuum Instruction Manual
Congratulations on the purchase of your new Prolux Lite Wet/Dry Garage Vacuum! The Prolux Lite Garage Vacuum is powerful, dependable, has a tool for nearly every job and is light and compact enough to be stored in nearly any Garage. It can vacuum up dirt, wood chips, saw dust, water, snow as well as blow, inflate, shampoo, spray and wash. With its 30 foot hose it is designed to keep your Garage, Shop or Cars clean when you need it.
Contents Safety Instructions ----------------------------------------------------------------4 Vacuum Description & Parts -----------------------------------------------------5 Assembly Instructions/Mounting Instructions ------------------------------------7 Operating Instructions ------------------------------------------------------------10 Using the Tools ------------------------------------------------------------------- 12 Maintenance --------------------------------------------------------------------
Important Safeguards! When using an electrical appliance, always follow basic precautions, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Warning: To reduce the risk of fire, electric shock, or injury: Do not use outdoors Close supervision is necessary when any appliance is used by or near children. Do not allow cleaning system to be used as a toy or to run unattended at any time. Do not allow any objects to be put into hose inlet.
Save these instructions! WARNING Operate cleaning system only at voltage specified on power unit. This system is intended for residential use. WARNING To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
Included Accessories & Parts 11. 32ft Flexible Wet/Dry Hose 12. Hose & Tools Holder 13. Extension Wands 15. Multi-Surface Floor Tool 16. Wet Pickup Squeegee Floor Tool 17. Crevice Tool 18. Dusting Brush 19. Upholstery Tool 20. Extraction Shampooer Suction Tool 21. 3 Sizes of Detailing & Inflator Tools 22. Long Detailing Precision Blower Tool 23. Wall Mounting Bracket 24. Screws 25. Mini Head with Spinning Brushroll 26.
Assembly Instructions 1. Remove the dirt tank by pulling up on both handles to unlatch. Lift upper half of unit to remove. 2. Remove all accessories and parts stored in the bottom of the tank prior to use. 3. If the round funnel comes out of dirt tank, set back inside the dirt tank before reassembling. 4. To reassemble, place the top of the unit on the dirt tank so the edges fit together and latch the handles to secure the top and bottom of unit. 5. Mount to wall (see instructions below).
Mounting on concrete wall (fasteners included) You will need: (4) 3/8” x 2-1/4” concrete sleeve anchors. 1. Drill a 3/8” x 1-3/4” hole with a masonry drill bit. 2. Insert a bolt and anchor sleeve into the hole. 4 holes 3. Align the bracket over the hole and mark the remaining hole locations using the (4) holes of the mounting bracket. Remove the bracket and drill remaining holes. 4. Mount the bracket starting at top corner hole, tightly securing sleeve anchor with hex nut. 5.
Mounting the Hose & Tool Holder (fasteners included) 1. Determine desired location for hose holder and screw supplied screw into stud. (If mounting into drywall with no stud available, use supplied drywall anchors.) 2. Attach the 4 screws in the backside of the Hose & Tool holder in the 4 holes. If you want to make the Hose & Tool Holder removable from your wall make the screws slightly loose and the Hose & Tool Holder can unsnap from your wall by pushing up on the Hose & Tool Holder. 3.
Operating Instructions Wet/dry vacuuming mode 1. Plug in unit and attach the hose connector into the air inlet. See picture ‘A’ below. Attach extension wand, if desired, to end of hose by pushing it firmly into the hoses and firmly twisting. All hose and tool connections are attached by friction fit method (shoving together and twisting to the right for firm connection). Attach additional wands or tools as desired. Switch the power on and start vacuuming.
Important: a. Unplug the unit when the indicator turns red and wait at least 5 seconds before attempting to resume the appliance. b. Empty the dust canister before vacuuming again. Two copper sensor poles on the probe should be clean, otherwise the sensing function of the probe will be affected. Probe c. After sucking up water, make sure the filters are dry before attempting to vacuum dust or dirt. d.
Blower Mode: This appliance also functions as a blower, sprayer, and shampooer. Attach to the blower hose to the outlet by inserting the gap in the tube plug to the hook of the exhaust and turn 90 degrees. See picture ‘A’ below. Attach extension wand, if desired, to end of hose by pushing it firmly into the hose. Attach additional wand or tool, if desired, by firmly inserting onto the wand. Start the appliance and begin blowing. Plug in the unit and push the power switch up to begin blowing.
Accessories: 32 ft flexible crush-proof hose Hose holder Accessory Caddy Mounting Bracket Floor cleaning: (2) Extension wands Use with desired attachment for a longer reach. Wet Pickup Squeegee Floor tool.
Auto Clean & Inflating: Water Extraction Suction tool. Precision blower tool for detailing Small, medium and large detailing and inflating tools. Spraying & Scrubbing: Mini Turbo Nozzle with Spinning Brushroll Hand Held Sprayer/ Shampooer TOOL USE 11. 32ft Flexible Crush-Proof Hose – Connects to the vacuum on suction side or blow side. 12. Hose Holder – 32 ft hose can be neatly stored here. 13. Extension Wands – 2 extension wands can be used for hard-to-reach places. Also it is used with floor tools. 14.
and because it was snowing outside, the snow drops to the floor and creates wet puddles. Simply take this floor tool and quickly suck up the dirty water in a matter of seconds. For mopping or cleaning your floor you could tilt the brush forward so the nylon scrub brushes are making contact and scrub your floor. Then bring the brush back to its normal level and suck all the dirty water and dirt into the vacuum. 17.
Spray the surface to be cleaned. Connect the hose to the suction side of the vacuum. Use extraction tool #20 to scrub your surface and suck out the dirty water. For more scrubbing power you may also use the mini head tool #25. The extraction tool #20 will suck the most water out. Then you’re done and that is how you shampoo your upholstery surfaces with the Prolux Wet Dry Garage vacuum. 3. 4. 5.
E. Wash the filters and allow to properly dry before reinstalling G: Clean the two copper poles of the probe Filter Maintenance: From ordinary use the circular filter (not the cloth filter) should be replaced or cleaned once every year or when warning light comes on (and dirt bin is clean). Replacing a dirty filter does improve suction performance. Cleaning clogs: Low suction or poor pickup may be due to a clog in the vacuum.
If the above methods are not successful, find the clog by hand, then squeeze the hose and shake until the debris dislodges. Troubleshooting 1) Limited suction power: If you find the suction power is limited or not working to capacity, follow the steps below to fix: a. First check the dust tank. Clean the filter and empty the dust tank. b. After cleaning, if problem persist check for clogs. c. If problem continues and there is no clog, replace or clean filters. 2) If appliance fails to start: a.
THREE (3) YEAR LIMITED WARRANTY Prolux warrants this product free from defects in material and workmanship for a period of three (3) years on the motor and (2) years on the body of the appliance.
