6000 / 7000 Upright Vacuum Instruction Manual
Contents Safety Instructions ----------------------------------------------------------------2-5 Included Parts --------------------------------------------------------------------6-7 Assembly Instructions ------------------------------------------------------------8-10 Operating Instructions ------------------------------------------------------------10-13 Using the Tools -------------------------------------------------------------------13-15 Maintenance ---------------------------------------------------
and keep this booklet as a permanent record of your purchase.
vacuum cleaner dealer for repair. 9. Do not pull or carry by the cord, use the cord as a handle, run appliance over cord, close a door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heater surfaces. 10. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord, and pull out of the outlet. 11. Do not handle the plug or the vacuum cleaner with wet hands. 12. Do not put objects into the openings. Do not use with any openings blocked.
WARNING Household Models 6000 & 7000 NOTE: As a safety feature and to reduce risk of damage, injury or electric shock, this vacuum cleaner is equipped with a polarized alternating current line plug (one blade wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If the plug still fails to fit, contact a qualified electrician to replace the outlet.
FEATURE COMPARISON CHART Feature/Mod Input Power Full el (amps) Control Indicator Light Length 6000 12.
FEATURE COMPARISON CHART Feature/Model Input (amps) Power Full Bag Head Control Indicator Light Cord Length (LED) 7000 12.
How To Use Friction Fit Cleaning Tools: Model 6000 8
The tools are connected by friction fit. Meaning to attach simply shove together and twist firmly. To remove simply untwist.
EASY ASSEMBLY INSTRUCTION Step One: Attaching the Handle 1. Remove handle screw. 2. Insert handle into top of dust cover with handle switch facing forward (Model 7000 only) 3. Align small hole on handle with screw hole in dust cover. Insert screw and tighten securely (All models). 4. Turn upper cord storage hook to upright position and wind cord between upper and lower hooks for storage. 5. To quick-release cord, simply rotate upper hook downward and cord will drop for immediate use.
Replacing the Dust Bag: *Remember: Always have a dust bag installed when operating your vacuum cleaner. Replace with a genuine dust bag when full. 1. Push down on knob at top of dust cover to open compartment. 2. Pull cardboard bag collar off holder. Remove and discard used dust bag. 3. Slide clean replacement bag collar onto holder. The bag lever must be positioned behind bag collar. Never pull up the lever, rather, push it down with dust bag. 4.
is needed, release the right tab on underside of bag supporter. Lift and rotate bag supporter to remove. 3. Remove secondary filter from bottom of dust compartment. 4. Replace secondary filter with new filter. 5. Reinstal l bag support er. Checking the Post Filter: The auxiliary post filter captures fine dust particles and purifies air exiting your vacuum cleaner. Change or clean the post filter with every third dust bag replacement, or as needed. 1.
Special Features Make Your Vacuum a Peak Performer! ON/OFF Switch: Model 6000 Vacuum Cleaners have a simple toggle switch on the dust compartment. Push down --- to start. Push down O to stop. Model 7000 is equipped with a convenient handle slide switch to turn power ON and OFF. Automatic Self-Adjusting Carpet Nozzle: Your vacuum can float evenly over varying carpet pile lengths. The carpet nozzle raises itself instantly and automatically.
On-board Cleaning Tools: Model 7000 Model 7000 is equipped with state-of-theart on-board cleaning tools including: • 2 piece telescoping wand • Extension wand • Crevice tool • Dusting brush • Upholstery tool To use: 1. Remove 2 piece telescoping wand from wand retainer. 2. Connect 2 piece telescoping wand to cleaning tools. Unlock wand collar to extend wand to desired length. 3. Attach selected cleaning tool to wand. (Tools may also be attached directly to flexible hose cuff, omitting extension wand.) 4.
6. Upholstery brush Connecting the Optional Hose Assembly: Simply lift the lid of the cleaning attachment opening located at the back of your vacuum cleaner and insert the hose end until it fits snugly. Connecting the Tools: Connect any of the cleaning tools to the extension wand or curved wand and twist for secure fit. Twist and pull apart to remove.
cleaning draperies, small rugs, etc., move the suction control slide on the back of the vacuum cleaner by increasing the opening until desired suction power is achieved. Close for normal vacuum operation. Note: Model 7000 full-bag indicator light will not operate while suction control is in open position. Replacing Headlight Bulb: Step One: Removing the bottom plate *Caution: First unplug the vacuum cleaner from the electrical outlet. 1. Use handle release pedal to place vacuum in Low position.
5. Replace with new bulb, turn clockwise. 6. Reinsert the headlight assembly back into the nozzle housing being careful not to pinch or re-arrange any wires and insert the two frame screws. 7. Reinsert bottom plate making certain that the hinges are in place on the front of the housing before sliding the two latches outward to fasten. Resetting the Thermal Switch: Model 7000 The Thermal Switch protects the motor from overheating. If the motor stops due to prolonged use, follow steps 1-5. 1.
1. Unplug the power cord. 2. Turn the unit over and remove the bottom plate as previously described under “Replacing Headlight Bulb Step One” on previous page. 3. Lift the rear belt cover up and back. 4. Remove the vented support fitting, noting position. 5. Remove agitator unit and worn out belt. 6. Loop new belt around motor drive shaft and agitator pulley. 7. Reinsert agitator unit into housing, making sure the two ends are positioned in the support guide. 8.
Changing the Agitator Brushes: Replace agitator brushes when they are worn or when the bristles do not touch a card held across the base plate. Replace all four brushes at the same time to maintain maximum cleaning performance. Remove agitator, start as described on previous page, Section 1 to 4. 1. Turn on end cap and remove. 2. Remove the agitator shaft. 3. Remove and replace the brushes on the shaft. 4. Reinstall the pulley and agitator holder making sure they are inserted completely and firmly. 5.
For Best Performance: 1. Keep machine and all accessories clean and in proper operating condition. 2. Change dust bags and filters as recommended to maintain optimum cleaning efficiency. 3. Always use genuine dust bags and filters. Use of other products may result in unsatisfactory cleaning or filtration performance. Filtration products are designed for maximum performance. 4. Have your vacuum cleaner checked regularly by your Authorized Vacuum Cleaner Dealer. 5.
Cleaning the Nozzle: The nozzle hose carries the dirt from the nozzle to the dust bag and also functions as the attachment cleaning hose. If it should become clogged: Model 6000 & 7000 Unplug the power cord. Open the lid of the cleaning attachment opening and remove clog or blockage. If the hose is still blocked, remove hose cuff from nozzle inlet. Turn the unit over, evoke bottom plate. Check nozzle inlet tube for obstructions. When clear, reinstall bottom plate.
What this limited warrant does not cover: • Expenses related to pick up, delivery or house calls. • Parts of the cleaner that require replacement under normal use, such as disposable dust bags, filters, drive belts, light bulbs, and brushroll bristles. • Damages or malfunctions caused by accident, acts of God, negligence, abuse, or use not in accordance with the Owner’s annual.