Owner manual

ManualsBrandsProMariner ManualsPower suppliersProNauticP

Digital

ProMar

Performance Charging

Digital

ProMar

Performance Charging

IMPORTANT NOTICE

This manual contains important safety and operating instructions for the ProNauticP Series Chargers.

Please save and read all safety, operating and installation instructions before installing or applying

AC power to your ProNauticP Charger.

Please call our Customer Care Department at 800-824-0524 from 8:30 am to 5pm Eastern Time

for any warranty, service or installation assistance. Thank you - ProMariner Customer Care

Your Satisfaction is Important to Us!

Do not return this product to retailer or dealer for any service or warranty requirements.

Model Number: Serial Number: Date of Purchase:

PLEASE RECORD YOUR:

Professional Mariner, LLC

200 International Drive, STE 195

Portsmouth, New Hampshire 03801

TEL: 603-433-4440

FAX: 603-433-4442

www.promariner.com

08/13 A

specifications subject to change without notice

Visit ProMariner online at www.promariner.com, for a complete

selection of quality marine products...

Here are just a few:

Visit frequently, we are always adding new products for your

boating enjoyment!

ProMite Series - Recreational Grade Waterproof Marine Battery Chargers

ProSport Series - Heavy Duty Recreational Grade Waterproof

Marine Battery Chargers

ProTournament Series - Professional Grade Tournament

Waterproof Marine Battery Chargers

ProIsoCharge Series - Digitally Controlled Zero Loss Charging Isolators

Digital Mobile Charge In-Transit Chargers

Battery Maintainers

AC Plug Holders

Battery Isolators

Isolation Transformers

Galvanic Isolators and Monitored Systems

Corrosion Control Products

Waterproof Marine Binoculars

Gold Plated Fuses and Holders

A Complete Line of Hand Held Test Meters

Online Technical Support and Service Support

ProNauticP Series Instruction Manual

Models Part No. Amperage Banks Volts

ProNautic1210P 63110 10 Amps 2 Banks 12

ProNautic1215P 63115 15 Amps 3 Banks 12

ProNautic1220P 63120 20 Amps 3 Banks 12

ProNautic1230P 63130 30 Amps 3 Banks 12

ProNautic1240P 63140 40 Amps 3 Banks 12

ProNautic1250P 63150 50 Amps 3 Banks 12

ProNautic1260P 63160 60 Amps 3 Banks 12

ProNautic2420P 63170 20 Amps 3 Banks 24

ProNautic2430P 63180 30 Amps 3 Banks 24

saving

energy

technology

™

Power Factor Corrected

100-260 VAC 50/60 Hz

Global AC Input

Summary of content (16 pages)

PAGE 1
ProMar Digital Performance Charging ProMar Digital Performance Charging Visit ProMariner online at www.promariner.com, for a complete selection of quality marine products...
PAGE 2
1 Table of Contents Notes Introduction... 2-3 CAUTIONS, WARNINGS AND SAFETY INSTRUCTIONS… 4-8 Installation... 9-12 Setup and Operation… 13-17 Programming... 18-19 Troubleshooting... 20 Maintenance... 21 Dimensions... 22-24 Typical Wiring Configuration... 25-27 Warranty Information... 28 Unpacking and Inspection: Thoroughly inspect your ProNauticP unit. The package should contain the following: 1) ProNauticP Charger 2) Parts package including: a. Owners/Installation manual b.
PAGE 3
2 Introduction 20 1 ProNautic 12•60 P Power Factor Corrected & Global AC Input 10 ProMar Digital Performance Charging SYSTEM DC OUTPUT LEVELS AC Power 9 Auto Temp Control Volts 2 Amps Active PFC 0% 1 2 Standby AUTO CONSERVATION MODES Charger Mode Self Test 5 OK Fault 3 100% Charger Output 3 Battery Health Program Charging Conditioning Auto Maintain Battery Profiles Equalization Charger Conditions Preset-2 Variable Speed Cooling Preset-1 Notes SETUP ENTER Flooded Reverse P
PAGE 4
3 Introduction Warranty Thank you from all of us at Professional Mariner, LLC and congratulations on the recent purchase of your ProNauticP Series On-Board Marine Battery Charger. The ProNauticP On-Board Marine Battery Charger is the latest in advanced microprocessor controlled battery charging technology and is ideal for: cuddy, cruiser, sail, house boats, yachts commercial offshore and sport fishing boats.
PAGE 5
4 27 Typical Wiring Configurations Warning Typical Single12 Volt DC Common Ground Installation: DO NOT attempt to install or operate the unit if it has been damaged in any way. IMPORTANT NOTICE – PLEASE READ AND UNDERSTAND THIS MANUAL BEFORE INSTALLING YOUR PRONAUTIC P SERIES CHARGER.
PAGE 6
26 5 Warning WARNING: HIGH VOLTAGE / ATTENTION : HAUTE TENSION Typical Wiring Configurations Typical 2 Bank12 Volt DC Common Ground Installation: AVOID SERIOUS INJURY OR DEATH FROM ELECTRICAL SHOCK. BEFORE OPENING TURN OFF AC SUPPLY POWER. CHOC ELECTRIQUES PEUVENT PROVOQUER LA MORT OU DE SERIEUSE BLESSURES. AVANT D'OUVRIR LA BOITE, COUPER LE COURANT. WARNING: LOW VOLTAGE / ATTENTION : BASSE TENSION ELECTRICAL BURN AND SPARK HAZARD. BEFORE OPENING DISCONNECT CHARGER CONNECTIONS AT BATTERY(S).
PAGE 7
6 25 Important Safety Instructions Typical Wiring Configurations Typical 3 Bank12 Volt DC Common Ground Installation: 7. WARNING – RISK OF EXPLOSIVE GASES.
PAGE 8
7 24 Dimensions b) Be sure the area around the charger and batteries is well ventilated while the batteries are being charged. Gases can be forcefully blown away using a piece of cardboard or other nonmetallic material as a fan. c) When cleaning battery terminals wear full eye protection to prevent corrosive material from coming in contact with eyes.
PAGE 9
23 8 Dimensions Important Safety Instructions ProNauticP (12 volt) 50-60 Amp and (24 volt) 30 Amp Dimensions Inches (mm) 4) Battery Location - This unit can not be mounted directly above or below a battery due to the corrosive nature of the gasses and electrolyte. Take care to ensure that spillage of electrolyte can be contained in a proper battery box or tray in the event of a leak and that the corrosive gas given off during the use and charge cycles cannot come into contact with the unit.
PAGE 10
9 22 Installation Dimensions CAUTION: Make sure AC Shore Power is Disconnected from the Boat and there is no presence of AC Power prior to installation. For new installations always connect Batteries as the LAST STEP. If you are replacing an existing battery charger please disconnect the battery charger output cables from the existing charger AND the battery(s). Do not use existing cables if they are not in compliance with the sizes detailed in this manual.
PAGE 11
21 10 Maintenance Installation This unit is solid state and requires no constant adjustment or constant attention; however, the following items should be checked: Maintenance Item Verify LED status panel shows no fault condition and indicates normal operation. Condition of fuses/breakers check for as-new condition on fuses (e.g. no discoloration or corrosion) and that a breaker will manually trip and reset.
PAGE 12
20 11 Installation Troubleshooting 2. Fuse Selection - As illustrated in the diagram, each positive conductor from the charger to the battery/battery bank must be fused. Choose a fuse that is 10 amps higher than the charger output (e.g. 60 amps, choose a fuse of 70 amps). These fuses come in a variety of sizes and types.
PAGE 13
19 12 Programming Installation 3. The Voltage and Amperage displays will show “FAC” “DEF” for factory default. 4. Press the SETUP/ENTER button to confirm selection, the charger will re-boot. SELECTING THE POWER SUPPLY MODE 1. Initiate self-test by repowering unit or by pressing the SETUP/ENTER and & buttons simultaneously for 5 second 2. While the digital display is indicating either “bc” or “PS” push either or to toggle the selection between “bc” and “PS” 3.
PAGE 14
18 13 Setup and Operation Programming Check List SELECTING BATTERY TYPE To select a battery type/charging profile perform the following: 1. Press and hold the SETUP/ENTER button for 5 seconds. 2. The current battery type and Voltage/Amperage displays will flash. 3. Use the and keys to select desired battery type. 4. The Volts and Amps readout will display the charge/conditioning and ready voltages for each profile highlighted. 5.
PAGE 15
14 17 Setup and Operation Setup and Operation Charger Service Conditions DC output service (reverse polarity) DC volts low DC volts high Red Amber Red Charger high temp Check fan Amber Red Indicates a reverse polarity situation (see troubleshooting) DC system voltage is less than 11.
PAGE 16
15 Setup and Operation Setup and Operation LED Status Indicator Center Function with remote temp sensor connected Performance Charging SYSTEM DC OUTPUT LEVELS AC Power equal to the charge in the selected profile based on state of charge based on state of charge if self test was initiated following successful self test based on state of charge based on state of charge based on state of charge NOTE: This LED configuration indicates that the charger is functioning normally and does not need any furt