Owner manual

18
Programming
SELECTING BATTERY TYPE
To select a battery type/charging profile perform the following:
1. Press and hold the “Setup/Enter” button for 5 seconds.
2. The current battery type and Voltage/Amperage displays will flash.
3. Use the
and keys to select desired battery type.
4. The Volts and Amps readout will display the charge/conditioning and ready
voltages for each profile highlighted.
5. Press the “Setup/Enter” button to confirm selection, the LED will remain solid.
ADJUSTING THE CUSTOM BATTERY TYPE SELECTION
NOTE: *Damage can result from improper use of the custom setting. Any damage experienced
while using this setting is the responsibility of the user and not covered by the Professional Mariner
warranty. ALWAYS consult the battery manufacturer if you are unsure of the battery chemistry.
1. Follow above steps and select the “Custom” option
2. The Volts and Amps will display 13.6 (default at 13.6V)
3. The “Charge/Conditioning” LED will be blinking, indicating it can be changed
4. Use the
and to select voltage up to 15.1.
5. Press the “Setup/Enter” button to confirm selection, the “Charge/Conditioning”
LED should be solid, the “Ready” LED should now be flashing
6. Use the
and to select voltage up to 15.1.
7. Press the “Setup/Enter” button to confirm selection, the LED will remain solid
NOTE: During this process, real-time voltage and amperages will not be displayed.
SELF TEST MODE
1. Press and hold the “Setup/Enter” and the
and buttons
simultaneously for 5 seconds.
2. Only the “Self Test” LED will flash until the test is complete.
3. OK or Fault LED’s will be displayed, see the Troubleshooting section
if the Fault LED is illuminated.
EQUALIZATION
NOTE: This function is only recommended for flooded lead acid batteries and will only activate
when this type of battery is selected.
1. Use the and to select the Equalization LED.
2. Once selected press the
and for 3 seconds.
3. The LED will remain solid, putting the unit in the equalization setting for 240 minutes.
4. Once complete, the charger will revert back to the previous setting.
POWER LEVEL ADJUSTMENT
1. Hold the
and buttons simultaneously for 15 seconds
2. Volts will display “PL” for Power Level
3. Press the
to adjust the amperage display from 100, 75, 50, 25% output.
Setup and Operation
Battery Types
Lithium Battery Caution: There are many types of Lithium batteries with various charging requirements.
Improper charging can result in damage to the battery or catastrophic failure of the battery resulting
in battery damage or even fire in extreme cases. You should take extreme caution in the selection of
your Lithium Battery system and the all of the onboard charging methods used for this type of battery.
The ProNauticP series only provides the bulk and float charging voltage and current for this type of
battery. The ProNauticP does not replace the required individual cell management electronics required
by lithium batteries. Consult your lithium battery supplier for details.
17
Auto Conservation Mode - Flooded or Sealed Batteries Only
Standby Amber Auto conservation mode enables, when
no change in battery charge over 72 hours
Battery Health Amber After 21 days of standby/float the charger
Program simulates a start-up charge mode
Charger Service Conditions
DC output service Red Indicates a reverse polarity situation
(reverse polarity) (see troubleshooting)
DC volts low Amber DC system voltage is less than 11.0 VDC
DC volts high Red Indicates a high DC voltage from an outside
source such as a failed alternator/regulator
Charger High Temp Amber Charger has shutdown due to high temperature
Check fan Red Fan failure
Digital Displays
Volts/amps Displays actual voltage/amperage used by the unit
Charger output Displays the actual vs available charge rate by percentage
User Selectable Battery Types
Battery Types Preset 1 Profiles Preset 2 Profiles
Charging DC voltage | Float DC Voltage Charging DC voltage | Float DC Voltage
Flooded 14.8 VDC 13.6 VDC 14.7 VDC 13.4 VDC
Sealed 14.4 VDC 13.6 VDC 14.6 VDC 13.4 VDC
AGM 14.4 VDC 13.4 VDC 14.6 VDC 13.7 VDC
GEL 14.0 VDC 13.7 VDC 14.4 VDC 13.8 VDC
LiFePO4 - Lithium 14.8 VDC 14.4 VDC 14.6 VDC 14.4 VDC
Calcium/Custom Programmable Programmable
VDC* default VDC* default
15.1 VDC 13.6 VDC 13.6 VDC 13.6 VDC
Equalization 15.5 VDC 15.5 VDC 15.5 VDC 15.5 VDC
*Damage can result from improper use of the custom setting. Any damage experienced while using
this setting is the responsibility of the user and not covered by the Professional Mariner warranty. ALWAYS
consult the battery manufacturer if you are unsure of the battery chemistry or appropriate selection.
*For 24 volt models double the voltages shown above or refer to product label.