proHarmony.
Introduction Promate’s proHarmony.1 is a sleek over-the-head designed Bluetooth® stereo headset with Hi-Fi output for wireless music and call streaming. It supports Multiple profiles – headset, hands-free, A2DP and AVRCP –, allowing even the most demanding Bluetooth® usage. The proHarmony.1 comes with a built-in lithium-ion battery for complete portability and longevity. With its rich sound and sophisticated wireless Bluetooth®, proHarmony1 is the ultimate device for audio and communication.
Packing Contents: proHarmony1 Micro-USB charging cable Warranty Card User Manual Getting Started I: Headband 2: < key :last song 3: > key :next song 4: LED Indicator 5: Multifunction button (MFB): Turn on/off the headset, answer, end and reject call, mute, voice dial and switch conversation, redial last number, pause and revert music.
Operation Instructions: Note: While connecting this Bluetooth® headset to your notebook’s built-in Bluetooth® adaptor, make sure that your notebook’s Bluetooth® adaptor supports A2DP, AVRCP and VOIP protocols. If mentioned protocols are not already available in your notebook’s Bluetooth® adaptor, you need to use an external USB Bluetooth® adaptor that supports AD2P, AVRCP and VOIP protocols. Charging Before using proHarmony.1 for the first time ensure the battery is fully charged for at least 3 hours.
Note: Choosing Travel charger or USB cable depends on different countries or areas and actual demands Warning: How to use 1 Switching on / off headset Function Switch on Operation Press the MFB for 3-5 seconds Indicator light The blue LED blinks quickly Indication tune A “DI” tone Switch off Press the MFB for 3-5 seconds The red LED blinks quickly A “DI” tone Remark: proHarmony1 will switch off automatically if no device is connected after 5 minutes in order to save power.
Note: The pairing mode will last for 2 minutes. If the headset still can’t pair with any Bluetooth® devices after 2 minutes, it will switch into standby mode automatically. 3 Pairing with Bluetooth® mobile phone Please make sure your mobile phone has Bluetooth® function that can be used. Special pairing procedures may vary with different mobile phone. Please refer to the manual of your mobile phone for further information.
4 Pairing with Bluetooth® transmitter You can enjoy music wirelessly by connecting proHarmony.1 with a stereo Bluetooth® transmitter. Pairing steps are as follows: a) Keep the Bluetooth® transmitter and proHarmony1 in the range of 1 meter when pairing. b) Press and the multi-function button for 5-7 seconds as described above to enter into pairing mode. c) Turn on the Bluetooth® transmitter and it will search Bluetooth® device automatically and start pairing.
Note: • After successful pairing with several Bluetooth® devices, the paired devices will remember each other. Unless paired information is deleted because of new pairing, otherwise make mobile phone and headset and set up hands free connection and restart the Bluetooth® transmitter, then the connection of several devices can be performed. • For the mobile phone which supports the HSP and A2DP at the same time. It may set up connection with HSP and A2DP simultaneously.
7 Making a call with the headset Function Voice dial Status of headset Standby mode Redial last call Standby mode Turn up volume Conversation mode Turn down volume Conversation mode Answer calling Ringing Reject calling Ringing End calling Conversation mode Switch conversation between headset and cell phone Conversation mode Microphone mute Conversation mode Cancel mute Conversation mute Operation Indication Press and hold A short tone “DU” “<” button for 2s (last song), release the key
• When the volume is adjusted to max or min, you will hear a indication sound of “Ding-Dong”. • For some mobile phones, when you press the key of accepting on the phone, the conversation will be sent to mobile phone. At this time, you can switch the call to headset by using the conversation switch button or through operating on the mobile phone. Please refer to the instruction of your mobile phone for further information.
• When the volume of headset is adjusted to max or min, you will hear an indication sound of “Ding-Dong”. • Remote control the function of last song/next song/pause/revert, it needs your mobile phone or Bluetooth® transmitter supports AVRCP. Please refer to the instruction of your mobile phone or Bluetooth® transmitter for further information. 9 LED indications 1. Charging LED indicator Red LED is on Red LED is off Status of headset Charging Charging Complete 2.
Care and maintenance Please read the following suggestions carefully, that will help you to fulfill any warranty obligations and to enjoy this product for many years. • Keep dry and don’t put it in the dump place, in case of effecting the interior circuit of product • Don’t put the product under the sunlight or place hot areas. High temperature will short the life of electronic device, destroy the battery, or distort certain plastic. • Don’t expose the product in the cold areas.
3 Q: How far is the effective range between the headset and mobile phone? A: According to the Bluetooth® standard, the max. controllable range of Class2 headset is 10 meters. It varies under different environment. 4 Q: Why my cell phone cannot search and find the headset? A: The mobile phone will not find the headset if headset and mobile phone are not under the pairing mode, Make sure the headset is under the pairing mode and in the effective working range, and then the headset can be paired and connected.
