Multimedia Projector MODEL PRM-30 Network Supported □ Wired LAN * Refer to the owner’s manual below for details about network function. □ Network Set-up and Operation □ PJ Network Manager Contact GT Innovations - Promethean Premium Partner for Victoria. Ph: 9798 7022 Email: info@gtinnovations.com.au Web: www.gtinnovations.com.
Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. Large ���������������� Screen in Limited ������������� Space Short focus lens allows you to project large images from short distance. (p.13) Security Features The projector can not be operated without remote control.
Table of Contents Features and Design . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . 3 To the Owner . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Instructions . . . . . . . . . . . . . . . . . . . . 5 Air Circulation Installing the Projector in Proper Position Moving the Projector 6 6 6 Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Part Names and Functions . . . . . . . . . . . . . .
To the Owner Before installing and operating this projector, read this manual thoroughly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in good condition for many years to come. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
Safety Instructions All the safety and operating instructions should be read before the product is operated. Do not install the projector near the ventilation duct of air-conditioning equipment. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. This projector should be operated only from the type of power source indicated on the marking label.
Safety Instructions Air Circulation Openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. CAUTION Hot air is exhausted from the exhaust vent. When using or installing the projector, the following precautions should be taken. – Do not put any flammable object or spray can near the projector, hot air is exhausted from the air vents.
Compliance Federal Communications Commission Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Part Names and Functions Front ① Lamp Cover ② Infrared Remote Receiver ③ Projection Lens ① ② Side ③ ④ ⑤⑥ ⑦ ⑪ ⑩ ⑨ ⑧ ④ LAN Connection Terminal ⑤ Indicators ⑥ Focus Ring ⑦ Power Cord Connector ⑧ Terminal Cover ⑨ Filter ⑩ Security Bar ⑪ Terminals and Connectors Note: ④ LAN Connection Terminal is for the Network function. Refer to the owner’s manual of “Network Set-up and Operation” . Kensington Security Slot This slot is for a Kensington lock used to deter theft of the projector.
Part Names and Functions Side Terminal ① ② ③ ④ ⑩ ⑨ ⑧ ⑦ ⑥ ⑤ ① CONTROL PORT When controlling the projector with RS-232C, connect the control equipment to this connector with the serial control cable. ⑦ COMPUTER IN 1 / COMPONENT IN Connect output signal from a computer, RGB scart 21-pin video output or component video output to this terminal (pp.14,16). ② COMPUTER / COMPONENT AUDIO IN Connect the audio output (stereo) from a computer or video equipment connected to ⑥, ⑦ or ⑧ to this jack (pp.14,16).
Part Names and Functions Top Panel ① LAMP REPLACE indicator ① ② ③ Turn yellow when the life of the projection lamp draws to an end. (pp. 63, 70) ② WARNING indicator Emit a red light when the projector detects abnormal condition. This also blinks red when the internal temperature of the projector exceeds the operating range. (pp. 60, 70) ③ POWER indicator It turns red when the projector is in the stand-by mode. It remains green while the projector is under operation. (pp.
Part Names and Functions Remote Control ① ④ VIDEO button Select the VIDEO input source. (p.37) ⑤ S-VIDEO button Select the S-VIDEO input source. (p.37) ② HDMI ③ ㉒ ④ ㉑ ⑳ ⑤ ⑦ SCREEN button Select a screen mode. (pp.26, 35-36, 43) ⑥ ⑲ ⑦ ⑱ ⑰ ⑯ ⑧ ⑨ ⑩ ⑥ Point ▲▼◄► buttons – Select an item or adjust the value in the On-Screen Menu. (p.21) – Pan the image in the Digital zoom +/- mode. (p.36) ASPECT ⑪ ⑮ ⑭ ⑬ ⑫ ① ON/STAND-BY button Turn the projector on or off. (pp.
Part Names and Functions Remote Control Battery Installation 1 Open the battery compartment lid. 2 Install new batteries into the compartment. 3 Replace the compartment lid. Two AAA size batteries For correct polarity (+ and –), be sure battery terminals are in contact with pins in compartment. To ensure safe operation, please observe the following precautions : ● Use two (2) AAA or LR03 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery.
Installation Positioning the Projector For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. The projector will focus at distance from 2.09' to 3.93' (63.6cm to 119.7cm). Note: • This projector is not equipped with an optical zoom. To adjust the screen size, change the throw distance. • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image.
Installation Connecting to a Computer Cables used for connection • VGA cables (Mini D-sub 15 pin) * • Audio cables • HDMI-DVI cable (*One cable is supplied; other cables are not supplied with the projector.
Installation Connecting to Video Equipment Cables used for connection • Video and Audio cable (RCA x 3) • S-video cable • Audio cable (Cables are not supplied with the projector. ) External Audio Equipment Audio Input Video and Audio Output (Video) (L) (R) Video and audio cable Audio cable (stereo) AUDIO OUT (stereo) VIDEO AUDIO IN S-video Output S-video cable S-VIDEO IN Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables.
Installation Connecting to Component Video Equipment Cables used for connection • Audio cables • Scart-VGA cable • Component cable • Component-VGA cable • HDMI cable (Cables are not supplied with this projector.
Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100–240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. If you are not sure of the type of power being supplied, consult your authorized dealer or service center.
Basic Operation Turning On the Projector 1 Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector. 2 Connect the projector’s AC power cord into an AC outlet. The POWER indicator lights red. 3 Press the ON/STAND-BY button on the remote control. The POWER indicator lights green and the cooling fans start to operate. The preparation display appears on the screen and the countdown starts.
Basic Operation Enter a PIN code Use the Point ▲▼ buttons to enter a number. Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number. Repeat this step to complete entering a four-digit number. PIN Code Input Dialog Box After the OK icon disappears, you can operate the projector.
Basic Operation Turning Off the Projector 1 Press the ON/STAND-BY button on the remote control, and Power off? appears on the screen. 2 Press the ON/STAND-BY button again to turn off the projector. The POWER indicator starts to blink red, and the cooling fans keep running. (You can select the level of fans’ quietness and speed. See “Fan” on page 57.) At this time, you can unplug the AC power cord even if the fans are still running.
Basic Operation How to Operate the On-Screen Menu HDMI The projector can be adjusted or set via the On-Screen Menu. The menu has a hierarchical structure, with a main menu that is divided into submenus, which are further divided into other submenus. For each adjustment and setting procedure, refer to respective sections in this manual. 1 Press the MENU button on the remote control to display the On-Screen Menu. 2 Use the Point ▲▼ buttons to highlight and select a main menu item.
Basic Operation Menu Bar For detailed functions of each menu, see “Menu Tree” on pages 68-69. Main Menu Sub-Menu ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ① Input Used to select an input source from Computer 1, Computer 2, HDMI, Video or S-video. (pp.27-28,37-38) ② PC adjust Select Auto PC adj., Fine sync, Total dots, Horizontal, Vertical, Current mode, Clamp, Display area H and Display area V to adjust the parameters to match with the PC input signal format. (pp.
Basic Operation Focus Adjustment Adjust the lens focus with the focus lever. Focus Lever Auto Setup Function Auto setup function is provided to automatically execute the setting of Auto setup (includes Input search and Auto PC adj. functions) in the Setting Menu by just pressing the AUTO SET button on the remote control. Refer to page 45 for the setting of the Auto setup function.
Basic Operation HDMI Sound Adjustment This projector has no speaker. Volume and Mute functions are effective for the AUDIO OUT jack. Direct Operation Remote Control Volume Press the VOLUME+/– buttons on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds. ASPECT VOLUME + button MUTE button VOLUME - button Mute Press the MUTE button on the remote control to select On to temporarily turn off the sound.
Basic Operation Remote Control Operation Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons enables you to make the desired operation quickly without calling up the On-Screen Menu. Remote Control COMPUTER 1/2, HDMI, VIDEO, S-VIDEO and COMPONENT buttons Press the COMPUTER 1/2, HDMI, VIDEO, S-VIDEO and COMPONENT buttons on the remote control to select the input source. See pages 27-28, 37-38 for details.
Basic Operation NO SHOW button Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When the projected image is captured and is set as User in the Logo selection (p.47), the screen changes each time you press the NO SHOW button as follows. No show disappears after 4 seconds.
Computer Input Input Source Selection (Computer 1: RGB) Direct Operation Choose Computer 1(RGB) by pressing the COMPUTER 1 button on the remote control. Remote Control HDMI COMPUTER 1 button Computer 1(RGB) ASPECT Computer 1(Scart) Menu Operation 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select Computer 1.
Computer Input Input Source Selection (Computer 2: RGB) Direct Operation Choose Computer 2 (RGB) by press the COMPUTER 2 button on the remote control. Remote Control HDMI COMPUTER 2 button COMPUTER 2 can not be selected when using the COMPUTER IN 2/ MONITOR OUT terminal as MONITOR OUT output. Computer 2 (RGB)* ASPECT Menu Operation 1 Press the MENU button to display the On-Screen Menu. Press the Point ▲▼ buttons, move the highlight to Input and then press the Point ► or the SELECT button.
Computer Input Computer System Selection This projector automatically tunes to various types of computers with its Multi-scan system and Auto PC adjustment. If a computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional settings. (Signal formats provided in this projector are shown on pages 71-72.
Computer Input Auto PC adjustment Auto PC adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal , Vertical and Clamp positions to conform to your computer. Menu Operation Auto PC adj. 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select PC adjust and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select Auto PC adj. and then press the SELECT button.
Computer Input Manual PC adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen Menu.
Computer Input Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select Yes. All adjustments will return to their previous figures. Mode free Menu Mode free To clear the stored data, select Mode free and then press the Point ► or the SELECT button. Move the highlight to the Mode that you want to clear and then press the SELECT button. This Mode has stored parameters.
HDMI Computer Input Image Mode Selection Direct Operation Select the desired image mode among Dynamic, Standard, Real, Blackboard (Green), Colorboard, Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Remote Control ASPECT IMAGE button Dynamic Standard Real IMAGE button Blackboard(Green) Colorboard Image 1 Menu Operation 1 Press the MENU button to display the On-Screen Menu.
Computer Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT Image adjust Menu button. 2 Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value. Contrast Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63).
Computer Input Store Menu Store To store the adjusted data, select Store and press the Point ► or the SELECT button. Use the Point ▲▼ buttons to select one from Image 1 to 4 and press the SELECT button. A confirmation box appears and then select Yes. Stored data can be called up by selecting an Image (1-4) in the Image Mode Selection on page 33. Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size.
Computer Input Custom adj. Adjust the screen scale and position manually with this function. Press the Point ► button at Custom adj. and the Custom adjustment menu is displayed on the screen, you can use the Point ▲▼ buttons to choose the item you want to adjust. Scale H/V........... Adjust the Horizontal/Vertical screen scale. H&V.................... When set to On, the aspect ratio is fixed. Scale V appears dimmed and becomes unavailable.
Video Input Input Source Selection (Video, S-video) Direct Operation Choose Video or S-video by pressing the VIDEO button or the S-VIDEO button on the remote control. Remote Control HDMI VIDEO button Video S-VIDEO button S-video ASPECT Menu Operation 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select either Video or S-video and then press the SELECT button.
Video Input Input Source Selection (Component, RGB Scart 21-pin, HDMI) Direct Operation Choose Computer 1(Component) or Computer 1(Scart) by pressing the the COMPONENT or COMPUTER 1 button on the remote control; choose HDMI by pressing the HDMI button on the remote control. Remote Control COMPUTER 1 button Computer 1 (RGB) HDMI Computer 1 (Scart) HDMI button HDMI COMPONENT button Menu Operation 1 Press the MENU button to display the On-Screen Menu.
Video Input Video System Selection 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select Video or S-video or Computer 1(Component) and then press the SELECT button. 3 Use the Point ▲▼ buttons to select System and then press the Point ► or the SELECT button. Use the Point ▲▼ buttons to select the desired system and then press the SELECT button.
HDMI Video Input Image Mode Selection Direct Operation Select the desired image mode from among Dynamic, Standard, Cinema, Blackboard (Green), Colorboard, Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Remote Control ASPECT IMAGE button Dynamic Standard Cinema Blackboard (Green) Menu Operation 1 2 IMAGE button Colorboard Press the MENU button to display the On-Screen Menu.
Video Input Image Adjustment 1 2 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select the Image adjust and then press the Point ► or the SELECT button. Image adjust Menu Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value. Contrast Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63).
Video Input Sharpness Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 15). Gamma Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15). Noise reduction Noise interference on the screen can be reduced. Select one of the following options to get smoother images. Off.......... Disabled. L 1.......... Lower reduction. L 2.......... Higher reduction.
Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size. 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Screen and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons select the desired item and then press the SELECT button. Screen Menu Normal Provide the image to fit the screen size while maintaining the aspect ratio of input signal.
Setting Setting This projector has a Setting Menu that allows you to set up the other various functions described below. 1 Press the MENU button to display the On-Screen Menu. Press the Point ▲▼ buttons to select the Setting and press the Point ► or the SELECT button to access the submenu items. 2 Use the Point ▲▼ buttons to select the desired item and then press the Point ► or the SELECT buttons to access the selected item.
Setting Auto setup This function enables Input search and Auto PC adjustment by pressing the AUTO SET button on the remote control. Settings for those functions can be altered as follows: Auto setup Input search This function detects the input signal automatically. When a signal is found, the search will stop. Use the Point ▲▼ buttons to select one of the following options. Off.......... Input search dose not work. On 1....... Input search works under the following situation.
Setting Keystone This function is used to adjust keystone distortion of the projected image. Use the Point ▲▼ buttons to choose the item you want to adjust. Keystone To correct keystone distortion, press the SELECT button. Keystone appears on the screen. Use the Point ▲▼ buttons to correct keystone distortion (p.23). Store Store...... Keep the keystone correction even when the AC power cord is unplugged. Reset......
Setting Logo (Logo and Logo PIN code lock settings) This function allows you to customize the screen logo with Logo select, Capture, Logo PIN code lock and Logo PIN code change functions. Logo select Note: When On is selected in the Logo PIN code lock function, Logo select and Capture functions can not be selected. Logo select This function decides on the starting-up display from among following options. Off............ Show the countdown display only. Default..... Show the factory-set logo. User......
Setting Capture This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations. Capture Select Capture and press the SELECT button. A confirmation box appears and select Yes to capture the projected image. After capturing the projected image, go to the Logo select function and set it to User. Then the captured image will be displayed the next time you turn on the projector.
Setting Enter a Logo PIN code Use the Point ▲▼ buttons to enter a number. Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number. Enter a Logo PIN code Repeat this step to complete entering a four-digit number. After entering the four-digit number, move the pointer to Set and press the SELECT button.
Setting Ceiling Ceiling When this function is set to On, the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to On, the picture will be left/right reversed. This function is used to project the image from rear of the screen. Rear Screen aspect This function is used to project the image to a 4:3 or 16:9 projection screen. 4:3 ..... Set to a 4:3 projection screen. 16:9 .....
Setting Standby mode This function is available when operating the projector via network. Network..... Supply the power to the network function even after turning off the projector. You can turn on/ off the projector via network, modify network environment, and receive an e-mail about projector status while the projector is powered off. Eco............. Select Eco when you do not use the projector via network. The projector’s network function will stop when turning off the projector.
Setting Direct on When this function is set to On, the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. Note: Be sure to turn off the projector properly (see “Turning Off the Projector” on page 20). If the projector is turned off in the incorrect sequence, the Direct on function does not work properly. P-timer This function allows you to change the presentation of the P-timer and execute it. Select one of the following options: Count up..............
Setting Closed caption Closed caption is a printed version of the program sound or other information displayed on the screen. If the input signal contains Closed captions, you can turn on the feature and switch the channels. Press the Point ▲▼ buttons to select Off, CC1, CC2, CC3 or CC4. If the Closed caption is not clear, you can change the text from Color to White. Closed caption Note: The Closed caption is available only under the situation below�.
Setting Lamp control This function allows you to change brightness of the screen. High .......... Brighter than the Normal mode. Normal....... Normal brightness. Remote control This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time.
Setting Security (PIN code lock) This function allows you to use the PIN code lock function to set the security for the projector operation. PIN code lock This function prevents the projector from being operated by unauthorized persons and provides the following setting options for security. Off............ Unlocked. On 1......... Enter the PIN code every time turning on the projector. On 2.........
Setting PIN code change The PIN code can be changed to your desired four-digit number. Press the SELECT button to select PIN code change. Current PIN code dialog box appears, use the Point ▲▼ buttons to enter the correct code. The New PIN code input dialog box appears. Set a new PIN code. caution: when you have changed THE PIn code, write down the new pin code in column of the pin code no. memo on page 76, and keep it securely. If you forget your PIN code, the projector can no longer be started.
Setting Fan This function provides the following options in the cooling fans’ operation when the projector is turned off (p.20). L 1...... Normal operation L 2...... Slower, lower-sound and longish-time than the normal operation (L1). Note: When L1 is selected in Fan menu and the projector is turned on right after it turned off, it may take a while to start projecting.
Setting Filter counter This function is used to set a frequency for the filter replacing. Filter counter When the projector reached a specified time between replacings, a Filter warning icon appears on the screen, notifying the replacing is necessary. After replacing the filter, be sure to select RESET and set the timer. The Filter warning icon will not turn off until the filter counter is reset. For details about resetting the timer, refer to “Resetting the Filter Counter” on page 61. Fig.
Information Input Source Information Display The Information Menu is used for checking the status of the image signal being projected and the operation of the projector. Direct Operation Press the INFO. button on the remote control to display the Information Menu. HDMI Remote Control INFO. button Menu Operation Press the Point ▲▼ buttons to select the Information. The Information Menu is displayed. ASPECT See below for displayed information. Input The selected input source is displayed.
Maintenance and Cleaning WARNING indicator The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING indicator is blinking red. When the temperature inside the projector reaches a certain level, the projector will be automatically shut down to protect the inside of the projector.
Maintenance and Cleaning Replacing the Filter Filter prevents dust from accumulating on the optical elements inside the projector. Should the Filter become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector. If a “Filter warning” icon appears on the screen, replace the Filter immediately. Replace the filter by following the steps below.
Maintenance and Cleaning Cleaning the Projection Lens Unplug the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use a lens cleaning paper or commercially available air blower to clean the lens. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the lens. Cleaning the Projector Cabinet Unplug the AC power cord before cleaning.
Maintenance and Cleaning Lamp Replacement When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode. Top Panel This indicator turns yellow when the projection lamp reaches the end of its life.
Maintenance and Cleaning Resetting the Lamp Counter Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP REPLACE indicator stops lighting and the Lamp replacement icon disappears. 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Setting and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select Lamp counter and then press the SELECT button.
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. –Make sure you have properly connected the projector to peripheral equipment as described on pages 14-16. –Make sure all equipment is connected to AC outlet and the power is turned on. –When the projector does not project an image from the connected computer, restart the computer. Problem: – Solutions No power – Plug the power cord of the projector into the AC outlet.
Appendix No image – Check the connection between your computer or video equipment and the projector. See pages 14-16. – See if the input signal is correctly output from your computer. Some laptop computers may need to change the setting for monitor output when connecting to a projector. See your computer’s instruction manual for the setting. – It takes about 15 seconds to display an image after turning on the projector. See page 18.
Appendix The image is distorted or runs off. – Check PC adjustment Menu or Screen and adjust them. See pages 31-32, 35-36. PIN code dialog box appears at start-up. – PIN code lock is being set. Enter a PIN code (the “1234” or numbers you have set). See pages 19, 55-56. The Remote Control does not work. – Check the batteries. – Make sure no obstruction is between the projector and remote control. – Make sure you are not too far from the projector when using the remote control.
Appendix Menu Tree Computer Input/HDMI Input/Video Input Input Input RGB Computer 1 Component RGB (Scart) RGB Computer 2 COMPUTER 2 can not be selected when using the COMPUTER IN 2/ MONITOR OUT terminal as MONITOR OUT output. HDMI Video S-video Sound Sound Volume Mute 0-63 On / Off Computer Input System (1) SVGA 1 Mode 1 Mode 2 ---- Image adjust Contrast Brightness Color temp. * Systems displayed in the System Menu vary depending on an input signal.
Appendix Computer Input/HDMI Input/Video Input Video Input System (2) System (3) Setting Auto 1080i 1035i 720p 575p 480p 575i 480i Language Auto setup Image adjust Keystone Keystone Background Blue / Black / User Display On / Countdown off / Off Logo Logo select Default Off User Capture Yes/No Logo PIN code lock Off / On Logo PIN code change Dynamic Standard Cinema Blackboard (Green) Colorboard Red / Blue / Yellow / Green Image 1 Image 2 Image 3 Image 4 Ceiling On / Off Rear On / Off Scr
Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators POWER red/green WARNING red Projector Condition LAMP REPLACE yellow The projector is off. (The AC power cord is unplugged.) The projector is in stand-by mode. Press the ON/STAND-BY button to turn on the projector. The projector is operating normally. The projector is preparing for stand-by or the projection lamp is being cooled down.
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below and less than 140 MHz of Dot Clock. When selecting these modes, PC adjustment can be limited.
Appendix When the input signal is digital from HDMI terminal, refer to the chart below. ON-SCREEN DISPLAY D-480p D-575p D-720p D-720p D-VGA D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 D-WXGA 7 D-WXGA 8 D-WXGA 9 D-1080i D-1080p D-1080p D-1080p RESOLUTION 640 x 480 768 x 575 1280 x 720 1280 x 720 640 x 480 800 x 600 1024 x 768 1366 x 768 1360 x 768 1376 x 768 1360 x 768 1366 x 768 1280 x 768 1280 x 768 1280 x 768 1280 x 800 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 H-Freq.
Appendix Technical Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 16.93 x 5.69" x 15.04" ( 430 mm x 144.4 mm x 381.9 mm ) (Including Ceilling plate) Net Weight ������������������ 12.52 lbs (5.68kg) (Including Ceilling plate) Panel Resolution LCD Panel System 0.
Appendix Accessories Owner’s Manual(CD-ROM) Network Application (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable PIN Code Label The specifications are subject to change without notice. LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
Appendix Configurations of Terminals COMPUTER IN 1 /COMPONENT IN Terminal: Analog RGB (Mini D-sub 15 pin) 4 5 10 15 3 9 14 2 8 1 7 12 13 6 11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 LAN TERMINAL 1 2 3 4 5 6 7 8 Red(R/Cr) Input Green(G/Y) Input Blue (B/Cb) Input ----Ground (Horiz.sync.) Ground (Red) Ground (Green) Ground (Blue) 87654321 TX + TX – RX + --------RX – --------- 5V Power Ground (Vert.sync.) Ground DDC Data Horiz. sync. Input (Composite H/V sync.) Vert. sync.
Appendix PIN Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service center. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set No: 4 3 2 1* *Should the four-digit number be changed, the factory set number will be invalid. While the projector is locked with the PIN code.
Appendix Dimensions Unit: inch(mm) Screw Holes for Ceiling Mount Screw: M5 Depth: 0.394(10.0) 1.18(30) 1.58(38.1) 6.56(166.7) 6.29(159.8) 5.69(144.4) 0.74(18.9) 0.59(15) 0.34(8.7) 2.51(63.8) 4.33(110) 4.33(110) 4.23(115) 7.53(191.3) 3.54(90) 0.56(14.2) 0.76(19.4) 6.78(172.1) 4.16(105.7) 1.65(42) 5.46(138.7) 12.80(325) 16.9(430) � � 2.76(70) 7.09(180) 7.09(180) � � 3.94(100) 6.77(172) 5.60(142.2) 15.04(381.
PROJECTOR KJ8YC Promethean Limited, Promethean House, Lower Philips Road, Whitebirk Industrial Estate, Blackburn, LANCS. BB15TH www.prometheanworld.
