ProMinent ® Operating Instructions Makro TZ Metering Pumps Makro TZMb Makro TZHa Makro TZMa Makro TZKa TZMb ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ TZMa ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ TZHa ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ TZKa ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ Please enter identcode of the device here.
Publishing details Publishing details: Operating Instruction Manual for ProMinent® Makro TZ © ProMinent Dosiertechnik GmbH, 2002 ProMinent Dosiertechnik GmbH Im Schuhmachergewann 5-11 69123 Heidelberg Germany info@prominent.com www.prominent.com Subject to revision Printed in the F.R. Germany ProMinent ® Page 2 BA_MA_TZ_006_10_06_GB.p65 2 05.02.
Contents Page Identcode ........................................................................................ 4 General user instructions ................................................................ 8 1 About this pump ................................................................. 9 2 Safety .................................................................................... 9 3 Storage, transport, unpacking ....................................... 11 4 Device overview, controls ..................
Identcode Identcode Please transfer the identity code listed under “Type” on the rating plate into the frame below TZMb M a k r o T Z 1 0 M o t o r- D r i v e n M e t e r i n g P u m p H A D B TZMb –– Drive type Main drive Add-on power end Double main drive Double add-on power end Pump type: (digits 1 +2 = back pressure [bar], digits 3-6 = feed rate [l/h] 120260 070430 040840 120340 070570 041100 120430 070720 041400 120510 070860 041670 120650 071070 042100 material version PCT/PPT/TTT max.
Identcode Identcode Please transfer the identity code listed under “Type” on the rating plate into the frame below TZMa Makro TZ 6/9 Diaphragm Metering Pump H A D B Drive type: Main drive Add-on drive Main drive double Add-on drive double Pump type: (digits 1 + 2 = back pressure, digits 3-6 = capacity [l/h 120190 060397 031875 120254 060529 031050 120317 060661 031395 120381 060793 031740 030750 032100 031000 032500 031250 031500 Material version PCA/PPE/TTT 10 bar max.
Identcode Identcode Please transfer the identity code listed under “Type” on the rating plate into the frame below TZHa Makro TZ 20 Hydraulic Diaphragm Pump H D Drive type: Main drive Double main drive Pump type: 160300 160500 160400 160600 160750 PC PP SS TT B A 100502 100669 100836 101004 101204 Double add-on power end Add-on power end material version PCA/PPE/TTT max.
Identcode Identcode Please transfer the identity code listed under “Type” on the rating plate into the frame below TZKa M a k r o T Z 2 0 M o t o r- D r i v e n M e t e r i n g P u m p ( P l u n g e r M e t e r i n g P u m p ) H D Drive type Main drive Double main drive B A Double add-on power end Add-on power end Pump type: digits 1 - 3 = back pressure [bar], digits 4 - 6 = feed rate [l/h] 320009 320018 192033 113058 063104 040163 028237 020322 320012 320024 192044 113077 063139 040217 028316 020430
General user instructions General user instructions Please read through the following user instructions carefully! They will help you get the best use out of the operating instruction manual. The following are highlighted in the text: • Enumerated points 왘 Instructions Operating guidelines: IMPORTANT Notices are intended to make your work easier. and safety guidelines: WARNING Describes a potentially dangerous situation. If not avoided, could cause fatal or serous injury.
About this pump / Safety 1 About this pump ® ProMinent Makro TZ dosing pumps are supplied with a 1.5 kW multi-voltage three-phase motor as standard (TZMb, TZMa: 0.75 kW). The stroke length can be adjusted between 0...20 mm (TZMb: 0...10 mm, TZMa: 0...6/9 mm). The acrylic resin coated cast housing can be combined with up to 16 liquid ends and 5 reduction ratios. Liquid ends are available in different material combinations to suit the particular dosing media.
Safety • Pumps which have been used with radioactive media cannot be sent. • Before commissioning the pump, connect the overpressure sensor and the diaphragm rupture sensor. CAUTION • It is prohibited to assemble and install ProMinent® metering pumps with parts which have not been approved or recommended by ProMinent. Damage to persons and property may ensue. • When metering aggressive media, check the resistance of the pump materials (See ProMinent® resistance list in the Equipment Catalogue or on www.
Safety / Storage, transport, unpacking / Device overview, controls Sound intensity level The sound intensity level is < 70 dB (A) at max. strokes, max stroke rate, max back pressure (water) in accordance with: DIN EN 12639 (Noise measurement, fluid pumps) 3 Storage, transport, unpacking The pump is delivered on a pallet. NOTICE • The pump is filled with oil on delivery. • Never lift the pump by the turret or the liquid end. • The pump must be placed on a level, stable base.
Device overview, controls 1 2 3 4 A Power end C Liquid end 4 C Fig. 4 A 5 C Makro TZMaD 1 Vent screw 2 Stroke adjustment wheel 3 Oil inspection window 4 Motor 5 Oil drain plug 6 1 2 3 4 Fig. 5 5 Diaphragm liquid end (for TZMb) ProMinent ® Page 12 BA_MA_TZ_006_10_06_GB.p65 1 Discharge valve 2 Liquid end 3 Diaphragm rupture sensor (TZMb only) 4 Suction valve 5 Leakage hole 6 Protective cover 12 05.02.
Device overview, controls 8 7 6 1 2 3 4 Fig. 6 5 1 Discharge valve 2 Liquid end 3 Suction valve 4 Oil drain plug, liquid end 5 Oil drain plug, feed tank 6 Filler opening, feed tank 7 Overpressure sensor terminal 8 Bleed valve Hydraulic diaphragm liquid end (for TZHa) 9 9 Bleed hose 10 Pressure relief valve 11 Oil inspection window – hydraulic oil 12 Diaphragm rupture sensor terminal 10 11 12 Fig. 7 Hydraulic diaphragm liquid end (for TZHa) ProMinent ® BA_MA_TZ_006_10_06_GB.
Device overview, controls 4 5 3 2 1 2 3 4 Suction valve Liquid end Discharge valve Hose nozzle for leakage/ flushing connector 5 Protective cover 1 Fig. 8 Piston liquid end (for TZKa) ProMinent ® Page 14 BA_MA_TZ_006_10_06_GB.p65 14 05.02.
Function description 5 Function description Function description, power end The ProMinent® MAKRO-TZ is an oscillating, pulse-free adjustable displacement pump. It is driven by a standard three phase motor whose drive rotation is reduced by a worm gear (1), transmitted to the push rod (4) via an adjustable eccentric cam (2) and a connector rod (3) and thus converted into an oscillating movement.
Function description Function description of a diaphragm liquid end (for TZMb and TZMa) The diaphragm (2) hermetically seals the pump volume inside the liquid end (3). When the diaphragm (2) is moved into the liquid end (3) the suction valve (4) closes and the metering chemical flows out of the liquid end via the discharge valve (1).
Function description Operation of the diaphragm rupture indicator (for TZMb) The diaphragm rupture indicator monitors the soundness of the composite diaphragm. The composite diaphragm combined with the diaphragm rupture sensor and switch make up the diaphragm rupture indicator. The composite diaphragm has an expandable position (4) on its bolt circle. If an outer layer of the composite diaphragm ruptures, dosing medium under pressure penetrates into it and causes the expandable position to bulge out (4).
Function description Description of the liquid end function The TZHa liquid end has a hydraulically actuated displacement element in the form of a highly durable composite diaphragm (2). It hermetically seals the feed cavity in the liquid end (3) and creates the displacement action within the liquid end at each pump stroke. The suction valve (4) and the discharge valve (1) together with the diaphragm action perform the feed process.
Function description The pump has a fixed setting pressure control valve (see Fig. 12) in the hydraulic end. The pressure control valve protects the pump (not the system! ) together with the overpressure sensor (9) and switches off the pump when the feed pressure is too high (=overpressure fuse). If the discharge side of the liquid end is blocked, the pressure control valve opens at the preset pressure and allows the hydraulic oil to flow back into the storage tank (8).
Function description Function description of a piston liquid end (for TZKa) The heart of the liquid end is a highly resistant, coated stainless steel piston (2). When the piston (2) moves into the liquid end the suction valve (1) closes and the feed chemical flows out of the liquid end via the discharge valve (3).
Assembly / Installation 6 Assembly Ambient temperature -10 °C to 40 °C Humidity Max. 95 % rel. humidity, non-condensing The pump must be bolted to an even, stable base. The base must be capable of permanently bearing the weight of the pump. Bolt the pump with the four bolts (M8) through the four bore holes in the frame into the pump feet or base if applicable. When fixed, the pump must not vibrate. NOTICE Contact ProMinent® if retrofitting an add-on pump.
Installation NOTICE Ensure that dust and foreign bodies cannot penetrate through the upper hose nozzle. The liquid end may otherwise be damaged. Connection of flushing collar (TZKa only) NOTICE • The flushing medium pressure may not exceed 0.5 bar. • The rinse aid must be suitable for the feed chemical and the liquid end materials. • It is essential to fit a flushing assembly if using very aggressive and poisonous media, or media with low lubrication properties.
Installation Cable assignment: blue - brown + Diaphragm rupture sensor Standard: 30 V DC/ 1A, volt-free contact (closed in normal condition). (for TZMb) For safety reasons, the application of a separated extra-low voltage is required (SELV in accordance with EN 60335-1). Cable assignment: any Intrinsically safe option: observe the enclosed operating instructions of the sensor (EX pump only)! 5 – 25 V DC, in accordance with Namur and DIN 19234, volt-free arrangement.
Commissioning 8 Commissioning WARNING • EX pump only: Always observe the “Important supplements for dosing pumps in EX areas” section of the “General operating instructions for ProMinent dosing pumps and hydraulic accessories”! CAUTION • Danger of burns from hot power end motor in the event of a fault! NOTICE • The pump is designed to meter liquid media within the stated capacity limits. • Note the limitations regarding high viscosity or density of the medium.
Commissioning TZMa 6 mm = 100 % stroke length (10 revolutions) 3.78 mm = 63 % stroke length (6 revolutions and 3 long increments) Stroke adjustment wheel: note the following: 1 revolution = 10 % 1 long increment = 1 % 1 short increment = 0.5 % TZKa, TZHa 20 mm stroke length = 100 % (10 revolutions) 12.6 mm = 63 % stroke length (6 revolutions and 3 long increments) Stroke adjustment wheel: note the following: 1 revolution = 10 % 1 long increment = 1 % 1 short increment = 0.
Commissioning / Operation / Maintenance IMPORTANT with regard to ball valve installation (single ball valve with Teflon ball seat only) If experiencing priming problems during installation: 왘 Ensure that there are no foreign bodies in the valve 왘 Place valve on a stable surface 왘 Tap the ball seat lightly with an approx. 300 g hammer and a brass rod 왘 Allow valves to prime while wet. The pump is now ready for operation. approx. 300 g Brass rod Fig. 15 The pump is now ready for operation.
Maintenance • Always wear suitable protective clothing to work on the liquid end when the pump has been used with hazardous or unknown media. • Metering pumps and their periphery must be maintained by qualified or authorised personnel. • Read the safety guidelines in the operating instruction manual before working on the motor. • Always disconnect external fans, stroke positioning motor or auxiliary equipment where present. Check that the power is disconnected.
Maintenance 1 (30 Nm) 2 (25 Nm) 3 Fig. 16 Makro TZ diaphragm liquid end (TZMb and TZMa) 1 Liquid end screws 2 Power end flange screws 3 Leakage hole 1 (30 Nm) 2 (25 Nm) ••••• Fig. 17 Makro TZ diaphragm liquid end (TZHa) 1 (15 Nm) Fig. 18 Makro TZ piston liquid end (TZKa) 1 Liquid end screws 2 turret flange screws 2 (25 Nm) 1 Liquid end flange screws 2 turret flange screws ProMinent ® Page 28 BA_MA_TZ_006_10_06_GB.p65 28 05.02.
Maintenance After approx. 5000 operating hours: Change gear oil. Gear oil Mobilgear 634 VG 460. ProMinent part no. 1004542 (1 l oil canister). Required oil quantity: 3.5 l Draining gear oil 왘 Unscrew bleed screw (1) 왘 Place an oil trough under the oil drain plug (2) 왘 Unscrew the oil drain plug (2) from the power end housing 왘 Allow the gear oil to drain out of the power end (approx. 3.5 l oil) 왘 Replace the seal on the oil drain plug (2). 1 3 2 Fig.
Repair 11 Repair WARNING • EX pump only: Always observe the “Important supplements for dosing pumps in EX areas” section of the “General Operating Instruction for ProMinent® Motor-Driven Metering Pumps and Hydraulic Accessories”! • Protect yourself against hazardous feed chemicals. • Always depressurise the suction and discharge lines before working on the pump! • Always empty the liquid end and rinse before starting maintenance and repair work if using dangerous or unknown media.
Repair 1 2 3 4 5 Fig. 21 1 2 3 4 5 Safety piston Spring Bush O-ring Expandable position on composite diaphragm 왘 Unscrew the hydraulic connections of the discharge and suction side. 왘 Slacken the locking screw and take the protective cover off the spacer. 왘 Screw the diaphragm rupture indicator out of the dosing head. 왘 Screw the bush (3) out of the dosing head. 왘 Remove the safety piston (1) with the spring (2) from the dosing head. 왘 Slacken the bolts (4) on the armoured disc.
Repair Repairing the diaphragm rupture sensor (TZMb only) The diaphragm rupture sensor must be checked after each diaphragm rupture and the separating diaphragm replaced if necessary (e.g. if dosing medium has escaped), and if the dosing medium is crystallising out or has entrained dirt and other particles.
Repair 1 Checking the diaphragm rupture sensor (EX version) 왘 Unscrew the diaphragm rupture sensor from the dosing head whilst the diaphragm is being changed 2 왘 Check that there is electrical continuity 3 3a 왘 Press in the channel of the diaphragm rupture sensor with a blunt insulated rod (2 – 3 mm diam.
Repair 11.2 Hydraulic diaphragm liquid end (TZHa) 왘 Set stroke adjustment knob to 0 % 왘 Unfasten union nuts and/or flange on valves and detach lines 왘 Empty liquid end and rinse is necessary 왘 Place an oil trough underneath the liquid end and hydraulic end 왘 Drain out the hydraulic oil from the hydraulic end via the acrylic glass stopper (3) (see Fig.) 왘 Lightly screw in the acrylic glass stopper (3) 왘 Unscrew the orange cover from the diaphragm rupture warning system (see Fig.
Repair 5 4 1 A Liquid end B Hydraulic end 1 2 3 4 5 Nuts Diaphragm Acrylic glass plug Breather hose Vent valve 2 3 Fig. 24 A B Function_HMH_1_2 왘 Remove the hose (4) from the bleed valve (5) and unscrew the valve 왘 Carefully remove the O-ring and the three filter meshes below the bleed valve 왘 Push a highly flexible hose (e. g. electrical shrink tubing) deep into the revealed opening to act as breather hose 왘 Push a very flexible hose (e.g.
Repair 왘 If the diaphragm rupture sensor opens at every stroke, unscrew it until it remains just open and then screw on nut 왘 Screw the housing back on (is the O-ring seated correctly beneath?) 왘 Tighten the union nut on the PG threaded connector (must be sealed.) Fig. 25 11.3 Diaphragm rupture sensor (*) Piston liquid end (TZKa) Disassembling liquid end 왘 Remove the protective cover (4) from the turret (see Fig.
Repair 왘 Remove the guide sleeves (5) and the guide bands (6), the packing collars (8) and the flushing collar (7) 왘 Clean the sealing area thoroughly 왘 Clean the piston (1), the guide sleeves (5) and the flushing collar (7) 왘 Dispose of the packing rings and the guide bands 왘 Insert the piston (1) Reassemble the parts in reverse order: 왘 Replace packing collars NOTICE Never push in packing collars with pointed instrument. This will deform packing collars or damage the piston.
Repair Positioning liquid end 왘 Place the liquid end onto the power end flange and screw in place (tightening torque 25 Nm) 왘 Grease the front end surfaces of the jointed head and the fork head 왘 Line up the holes of the coupling head and the fork head (see Fig.
Repair 11.4 Valve servicing Servicing ball valves 왘 Screw valve cover (5) onto the suction side 왘 Take the parts carefully out of the valve body (2) 왘 Replace worn parts 왘 Clean remaining parts 왘 Check all parts 왘 (Where applicable: place the compression springs into the valve body (2)) 왘 Insert the valve body (3) and the valve seat (4) 왘 Screw in the valve cover (5). 1 2 3 4 5 Fig.
Repair 1 2 3 4 5 (6) 7 8 Fig. 31: Discarge valve (arrow = direction of flow) 1 2 3 4 5 6 7 8 Valve body Valve seat Ball Valve housing Seal Spring (optional) Insert disc Seal (liquid end) Reassembling discharge valve: IMPORTANT Check the alignment of the valve seat (2) when assembling. The valve seat (2) acts as the ball seat on the smooth side and on the other it acts as the ball cage and spring guide. The smooth side should point in the direction of flow in all valve types.
Repair IMPORTANT The distance between the edge of the ball body and the insert disc depends on the design. 왘 Lay the large seal (8) between the insert disc (7) and the liquid end 왘 Screw the valve up to the stop. Cleaning a suction valve: The suction valve is basically dismantled, cleaned and reassembled in precisely the same way as the discharge valve. However, note when assembling the valve seat (2) that it should face the opposite direction.
Repair Servicing plate valves NOTICE Do not scratch the finely finished seal surfaces on the valve plates (3) or the valve inserts (4)! 왘 왘 왘 왘 왘 왘 왘 왘 Screw the valve body bush (5) onto the suction side Take the parts carefully out of the valve body (2) Replace worn parts Clean remaining parts Check all parts Place the compression springs (1) into the valve body (2) Insert the valve plate (3) Screw in the valve cover (4).
Troubleshooting 12 Troubleshooting WARNING • EX pump only: Always observe the “Important supplements for dosing pumps in EX areas” section of the “General Operating Instruction for ProMinent® Motor-Driven Metering Pumps and Hydraulic Accessories”! • Metering pumps and their peripherals must be maintained and repaired by qualified or authorised personnel. • For all dosing pumps for dosing flammable media, the following applies: start up and draining only under specialist supervision.
Decommissioning and disposal 13 Decommissioning and disposal Decommissioning WARNING • EX pump only: Always observe the “Important supplements for dosing pumps in EX areas” section of the “General Operating Instruction for ProMinent® Motor-Driven Metering Pumps and Hydraulic Accessories”! • Metering pumps and their peripherals must be decommissioned by qualified or authorised personnel.
Technical data 14 Technical data WARNING Only for modified version: Please observe the “Supplement for modified version” at the end of the section! It replaces and supplements the technical data! Table of main pumps diaphragm liquid ends (TZMb) Pump type TZMbH with 1500 rpm motor at 50 Hz with 1800 rpm motor at 60 Hz Capacity at max. back pressure Max. stroke frequency Capacity at max. back pressure Stroke count at max.
Technical data Table of main pumps diaphragm liquid ends (TZMa) Pump type TZMa with 1500 rpm motor at 50 Hz with 1800 rpm motor at 60 Hz Capacity at max. back pressure Max. stroke frequency Capacity at max. back pressure Stroke Suction count at lift max. back pressure Connection suction/ discharge side Shipping weight strokes/ min. psi strokes/ min.
Technical data Table of main pumps hydraulic diaphragm liquid ends (TZHa) with 1500 rpm motor at 50 Hz with 1800 rpm motor at 60 Hz Capacity at max. back pressure Max. stroke frequency Capacity at max. back pressure Max. Suction stroke lift frequency Connection Shipping Hydraulic suction/ weight discharge side strokes/ min. psi strokes/ min. m WG G-DN Pump type TZHa bar l/h ml/ stroke l/h/gph kg* Ø mm 160300 16 300 69.4 72 232 424/112 86 3 1 1/2-25 80 70 160400 16 400 69.
Technical data with 1500 rpm motor at 50 Hz with 1800 rpm motor at 60 Hz Capacity at max. back pressure Max. stroke frequency Capacity at max. back pressure strokes/ min. psi l/h ml/ stroke l/h/gph Max. Suction Connection stroke lift suction/ frequency discharge side strokes/ m WG G-DN min. Pump type TZKa bar 192033 192 32.9 7.6 72 2776 39/ 10 86 4 192044 192 43.9 7.6 96 2776 59/ 14 115 4 192055 192 54.8 7.6 120 2776 66/ 17 144 168066 168 65.8 7.
Technical data Accuracies - The reproducibility for the TZKa is better than ± 0.5 % in the stroke length range from 10 - 100 % and better than ± 1 % for the TZHA (TZMa: ± 1 % at 30 % - 100 %) (with measurements under constant conditions with water at 20 °C – with correct installation, p > 1 bar) - The dosing accuracy is approx ± 1 % at maximum stroke length and maximum back pressure.
Technical data Electrical data Stroke sensor (option) intrinsically safe 5-25 V DC, in accordance with Namur and DIN 19234, volt-free arrangement. Nominal voltage: 8 V DC (Ri ~ 1 kΩ) Current consumption: active surface clear > 3 mA active surface covered < 1 mA on). e is required Nominal contact spacing: 1.5 mm The evaluation / supply device must be able to evaluate the changes in current in order to indicate a diaphragm rupture. ns of the sensor Cable assignment: arrangement.
Technical data Environmental conditions Storage temperature -10 °C to 50 °C Ambient temperature -10 °C to 45 °C Humidity: 95 % rel. humidity, non-condensing Maximum feed chemical temperatures for liquid ends: Diaphragm liquid ends (TZMb, TZMa and TZHa) Material Piston liquid ends (TZKa) long term at max back pressure. short term at max. 2 bar (15 min) PC 45 °C 60 °C PP 60 °C 100 °C PTFE 90 °C 120 °C Stainless steel 90 °C 120 °C Material long term at max.
Technical data Identcode: 040840, 041100, 041400, 041670, 042100 Liquid end FM 2100 - DN 40 PP Fördereinheit 1025170 P 1025169 T 1025174 S 1022930 S (without valve set) 1022929 PTFE composite pump diaphragm for TZMb ProMinent® DEVELOPAN® pump diaphragm made from EPDM with a woven inlay, generous integrally vulcanised steel core and PTFE Teflon coating on the surface in contact with the medium. Description for pump type Order No.
Technical data Type TZHa Spare parts kits Makro TZ (TZHa) The spare parts kit generally contains all the liquid end parts subject to wear 1 pump diaphragm 1 suction valve set 1 discharge valve set 2 valve balls (DN 40 with plate and Hast. C spring) 1 set of seals (O-rings, valve seat, valve seat bushes) Order No.
Technical data Accessories Type TZMa TZMb TZKa • stroke length actuator/control motor (on request) • actuator with positioning motor for automatic stroke length adjustment (on request) • variable-speed motor with integrated frequency converter (on request) • speed control systems (on request) • universal dosing control system Dos control (on request) Mounting frames for Makro TZ TZMaA and TZMaB, TZMbA and TZMbB, TZKaA and TZKaB A mounting frame must be provided for combinations of main and add-o
Technical data Supplement for modified version: (Identity code item “Version”: “M-modified”) [Affix sticker with modified data here!] ProMinent ® BA_MA_TZ_006_10_06_GB.p65 Page 55 55 05.02.
Appendix Technical specification Makro TZ (TZMbH) Main power end 551 436 181 645/705# C 115 376 B A 160 F 200 220 Ø9 225 5 245 D E (93) 61_01_101_00_59_74_1x01 Dimension # with handwheel Dimensions Makro TZ TZMb (in mm) Type 120260, 120340, 120430, 120510, 120650 S 120260, 120340, 120430, 120510, 120650 PP, P, T 070430, 070570, 070720, 070860, 071070 S 070430, 070570, 070720, 070860, 071070 PP, P, T 040840, 041100, 041400, 041670, 42100 S 040840, 041100, 041400, 041670, 42100 PP, P
Appendix Technical specification Makro TZ (TZMbH and TZMbD) Main power end with add-on power end Double head version F 220 60 200 G 436 H 549 250 115 61_01_101_00_59_74_2x01 Dimensions Makro TZ TZMbH and TZMbD Type 120260, 120340, 120430, 120510, 120650 S 120260, 120340, 120430, 120510, 120650 PP, P, T 070430, 070570, 070720, 070860, 071070 S 070430, 070570, 070720, 070860, 071070 PP, P, T 040840, 041100, 041400, 041670, 42100 S 040840, 041100, 041400, 041670, 42100 PP, P, T F 215 215 222
Appendix Technical specification Makro TZ (TZMaH) Main power end 551 436 181 115 C 376 B A 160 ø9 5 225 ( 43 ) 220 F 200 245 D E 61_01_101_00_17_74 Dimensions Makro TZ TZMa (in mm) Type120190, 120254, 120190, 120254, 060397, 060529, 060397, 060529, 030750, 031000, 030750, 031000, 031050, 031395, 031050, 031395, 120317, 120381 120317, 120381 060661, 060793 060661, 060793 031250, 031500, 031250, 031500, 031740, 032100, 031740, 032100, 031875 031875 032500 032500 S PP, P, T S PP, P, T S PP, P,
Appendix Technical specification Makro TZ (TZMaA, TZMaB und TZMaD) Main power end with add-on power end Double head version 645 /705** 200 436 F 220 549 G 250 115 H ** Measurement with handwheel Dimensions Makro TZ TZMaH and TZMaD (in mm) Type HM ..-130 S HM ..-130 PP, P, T HM ..-260 S HM ..-260 PP, P, T HM ..-530 S HM ..530 PP, P, T HM ..-1500/2100 S HM ..
Appendix Technical specification Makro TZ (TZHaH) Main power end 592 477 191 115 C 376 A B 160 Ø9 F 200 ( 58 ) 220 225 5 245 D E 61_01_101_00_18_74 Dimensions Makro TZ TZHaH (in mm) Type HMH. ..-70/20 S HMH. ..-70/20 PP, P, T HMH. ..-90/20 S HMH. ..
Appendix Technical specification Makro TZ (TZHaA, TZHaB und TZHaD) Main power end with add-on power end Double head version 645 /705** 200 F 220 477 G 590 H 302 115 ** Measurement with handwheel Dimensions Makro TZ TZHaH and TZHaD (in mm) Type HMH. ..-70/20 S HMH. ..-70/20 PP, P, T HMH. ..-90/20 S F 251 251 261 261 G 701 701 723 723 H 785 807 836 854 ProMinent ® BA_MA_TZ_006_10_06_GB.p65 HMH. ..-90/20 PP, P, T Page 61 61 05.02.
Appendix Technical specification Makro TZ (TZKaH) Main power end 551 /592** 436 /477** 181 115 C 376 B A 160 200 Ø9 Ø8 F ( 43 ) 220 225 5 245 D E** 61_01_101_00_19_74 Dimensions Makro TZ TZKaH (in mm) Type HK ..-12 S HK ..-17 S HK ..-23 S HK ..-30 S HK ..-40 S HK ..-50 S HK ..-60 S HK ..-70 S HK ..
Appendix Technical specification Makro TZ (TZKaA, TZKaB and TZKaD) Main power end with add-on power end Double head version 645 /705** F 200 220 G 436 H 549 250 115 ** Measurement with handwheel Dimensions Makro TZ TZKaH and TZKaD (in mm) Type HK ..-12 S HK ..-17 S HK ..-23 S HK ..-30 S HK ..-40 S HK ..-50 S HK ..-60 S HK ..-70 S HK ..
Appendix Motor Datenblatt / Motor data sheet Bestell Nr. order no. / no. de commande 741229 Motor-Typ motor type type du moteur AF 80/4B – 11 Maschinenart type of machine designation 3-ph.
Appendix Motor Datenblatt / Motor data sheet Bestell Nr. order no. / no. de commande 741230 Motor-Typ motor type type du moteur AF 90L/4I – 11 Maschinenart type of machine designation 3-ph.
EC Declaration of Conformity For pumps without EX-protection: ProMinent ® Page 66 BA_MA_TZ_006_10_06_GB.p65 66 05.02.
EC Declaration of Conformity For pumps with EX-protection: ProMinent ® BA_MA_TZ_006_10_06_GB.p65 Page 67 67 05.02.
Page 68 05.02.2007, 13:41 Uhr 0 100 200 300 400 500 600 700 0 100 200 300 400 500 600 700 0 0 1 20 2 120650 120510 120430 120340 120260 10 120650 120510 120430 120340 120260 3 4 5 6 7 8 Druck / pressure in [bar] 30 40 50 60 70 Hublänge / stroke length in [%] 9 80 10 11 90 12 100 Dosierleistung / capacity Q in [l/h] BA_MA_TZ_006_10_06_GB.
BA_MA_TZ_006_10_06_GB.p65 69 Dosierleistung / capacity Q in [l/h] Dosierleistung / capacity Q in [l/h] ProMinent ® 05.02.
Page 70 05.02.2007, 13:41 Uhr 0 100 200 300 400 500 600 700 0 100 200 300 400 500 600 700 0 0 1 20 2 120510 120430 120340 120260 10 120510 120430 120340 120260 3 4 5 6 7 8 Druck / pressure in [bar] 30 40 50 60 70 Hublänge / stroke length in [%] 9 10 80 11 90 12 100 Dosierleistung / capacity Q in [l/h] Dosierleistung / capacity Q in [l/h] BA_MA_TZ_006_10_06_GB.
BA_MA_TZ_006_10_06_GB.p65 71 Dosierleistung / capacity Q in [l/h] Dosierleistung / capacity Q in [l/h] ProMinent ® 05.02.
Performance diagrams Makro TZ diaphragm dosing pumps TZMa per liquid end at 50 Hz Appendix Page 72 BA_MA_TZ_006_10_06_GB.p65 ProMinent ® 72 05.02.
Performance diagrams Makro TZ diaphragm dosing pumps TZMa per liquid end at 50 Hz NOTE Performance diagrams Makro TZ piston dosing pumps TZKa available on request Appendix ProMinent ® BA_MA_TZ_006_10_06_GB.p65 Page 73 73 05.02.
Page 74 05.02.2007, 13:41 Uhr 0 100 200 300 400 500 600 700 800 0 100 200 300 400 500 600 700 800 0 0 1 20 2 3 160750 160600 160500 160400 160300 10 160750 160600 160500 160400 160300 4 5 6 7 8 9 10 11 Druck / pressure in [bar] 30 40 50 60 70 Hublänge / stroke length in [%] 90 100 12 13 14 15 16 80 Dosiermenge / capacity Q in [l/h] BA_MA_TZ_006_10_06_GB.
Dosiermenge / capacity Q in [l/h] Dosiermenge / capacity Q in [l/h] BA_MA_TZ_006_10_06_GB.p65 ProMinent ® 05.02.
Die ProMinent Firmengruppe / The ProMinent Group Stammhaus / Head office ProMinent Dosiertechnik GmbH · Im Schuhmachergewann 5-11 · 69123 Heidelberg · Germany info@prominent.com · www.prominent.com · Tel.: +49 6221 842-0 · Fax: +49 6221 842-617 Tochtergesellschaften / Subsidiaries ProMinent Fluid Controls Pty. Ltd. (Australia) Tel.: +61 2 94500995 sales@prominentfluid.com.au www.prominentfluid.com.au ProMinent Dosiertechnik Ges. mbH (Austria) Tel.: +43 7448 30400 office@prominent.at www.prominent.