VTRAK E-Class E830f/i, E630f/i PRODUCT MANUAL Version 1.
VTrak E-Class Product Manual Copyright © 2011 PROMISE Technology, Inc. All Rights Reserved. PROMISE, the PROMISE logo, VTrak, SmartStor, SuperTrak, FastTrak, VessRAID, Vess, PerfectPATH, PerfectRAID, SATA150, ULTRA133, VTrak S3000, BackTrak, HyperCache, HyperCache-R, HyperCache-W, DeltaScan and GreenRAID are registered or pending trademarks of PROMISE Technology, Inc. in the U.S. and other countries. All other trademarks are the property of their respective owners.
Contents Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 VTrak Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Architectural Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VTrak E-Class Product Manual Chapter 4: Management with WebPAM PROe, cont. Managing Background Activities . . . . . . . . . . . . . . . . . . . . . . . . . .114 Managing Storage Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 Working with the Event Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . .135 Monitoring Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 Managing Physical Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Chapter 6: Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .315 Updating the Subsystem Firmware . . . . . . . . . . . . . . . . . . . . . . . .315 Updating Physical Drive Firmware . . . . . . . . . . . . . . . . . . . . . . . .321 Replacing a Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323 Replacing a Cache Backup Battery . . . . . . . . . . . . . . . . . . . . . . . .324 Replacing a RAID Controller – Dual Controllers . . . . . . . . . . .
VTrak E-Class Product Manual Appendix B: Multipathing on Windows . . . . . . . . . . . . . . . . . . . . . .449 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .449 Installing PerfectPath . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450 Verifying Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 Running Perfect Path View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1: Introduction This chapter covers the following topics: • About This Manual (below) • VTrak Overview (page 2) • Architectural Description (page 3) • Features (page 6) • General Specifications (page 10) • Safety and Environmental (page 12) • Warranty and Support (page 14) About This Manual This Product Manual describes how to setup, use, and maintain the VTrak E830f, E830i, E630f, and E630i external disk array subsystems.
VTrak E-Class Product Manual Note A Note provides helpful information such as hints or alternative ways of doing a task. VTrak Overview The PROMISE VTrak Ex30 series support for 6 Gb/s SAS and SATA disks and a next-generation embedded storage I/O processing platform out to set a new performance standard while providing a reliable, flexible and easy to manage RAID storage system. The VTrak E830f and E630f are coupled with high speed 8 Gb/s Fibre Channel host connectivity.
Architectural Description industry leading warranty, PROMISE offers extended warranty and onsite parts replacement options with service levels with response times as low four hours. Architectural Description The VTrak Ex30 series subsystems are suitable for Direct Attached Storage (DAS), Storage Area Network (SAN), and Expanded Storage.
VTrak E-Class Product Manual Figure 2. VTrak E630f/i front view Drive Carrier LEDs Drive Carriers Power and Status LEDs Figure 3.
Architectural Description Figure 4. VTrak E630f back view RAID Controller 1 RAID Controller 2 Power Supply 1 Power Supply 2 Figure 5.
VTrak E-Class Product Manual Figure 6. VTrak E630i back view RAID Controller 1 RAID Controller 2 Power Supply 1 Power Supply 2 Features Controller Module Features Drive Support • 3.5-inch and 2.5-inch form factor • Hard disk drives (HDDs) and Solid State drives (SSDs) • SAS, 6 Gb/s and 3 Gb/s • SATA, 6 Gb/s and 3 Gb/s • Supports any mix of SAS and SATA drives simultaneously in the same enclosure For a list of supported drives, go to PROMISE support: http://www.promise.
Features Data Cache • 2 GB data cache per controller.
VTrak E-Class Product Manual • Disk SMART Polling • Online Capacity Expansion (OCE) • RAID Level Migration (RLM) • UPS Monitoring • Feature rich task scheduler for background activities PerfectRAID Features • Predictive Data Migration (PDM) • Intelligent Bad Sector Remapping • SMART Error Handling • NVRAM Error Logging • Disk Slot Power Control • Read/Write Check Table • Write Hole Table GreenRAID Features • Four levels of advanced power management disk drive (MAID) support • Eff
Features Supported Operating Environments Core Platform Type Notes Microsoft Windows Server 2008 with SP2 x86/x64 Windows Server 2008 Hyper-V with SP2 x64 Windows Server 2008 R2 x64 ALUA support with PerfectPath v4.00 or later Oracle Enterprise Linux 5.3 x64 No LUN Affinity/ALUA support Enterprise Linux 5.5 x64 LUN Affinity/ALUA natively supported Enterprise Linux 5.3 x86/x64 No LUN Affinity/ALUA support Enterprise Linux 5.4 x86/x64 Enterprise Linux 5.
VTrak E-Class Product Manual Supported Browsers Browsers run on the host PC or server, from which you monitor and manage the VTrak subsystem using WebPAM PROe. The browsers listed here meet the minimum version requirements for browser compatibility: • Internet Explorer – 8.0.7600.16385 • Firefox for Windows – 3.6.13 • Firefox for RHEL – 3.0.18 • Firefox for SLES 11.1 – 3.5.9 • Safari for MacOS – 4.0.5 (6531.22.7) • Safari for Windows – 5.0.2 (7533.18.
General Specifications Humidity Range • Operational: 10% to 90% (Non-Condensing) • Non-Operational: 5% to 95% (Non-Condensing) Noise, Shock, and Vibration Acoustic Noise Levels • Typical: 55 dB • Maximum: 65 dB Shock • Operational: 5G, 11 ms duration • Non-Operational: 10G, 11ms duration Vibration • Operational: 0.3G, 5 to 500 Hz • Non-Operational: 1G, 5 to 500 Hz Dimensions (Height, Width, Depth) • 4U/24 Bay: 17.4 x 44.7 x 50.7 cm (6.9 x 17.6 x 19.96 in) • 3U/16 Bay: 13.1 x 44.7 x 50.
VTrak E-Class Product Manual Safety and Environmental EMI/RFI Statements BSMI CE Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. FCC This device complies with Part 15 of the FCC Rules.
Safety and Environmental Environmental Standards • RoHS • GreenPC • WEEE Warnings and Cautions Warnings and Cautions are placed in this Product Manual beside the user actions to which they apply.
VTrak E-Class Product Manual • “USB Support Reports a Problem” on page 390 • “Unsaved Data in the Controller Cache” on page 398 Warranty and Support Warranty • Three year complete system limited warranty with advanced parts replacement • Optional extended warranty • Optional onsite parts replacement program Support • 24 hour, 7 days a week, 365 days a year e-mail and phone support (English only) • 24 hour, 7 days a week, 365 days a year access to PROMISE support site • Firmware and compatibi
Chapter 2: Installation This chapter covers the following topics: • Unpacking the VTrak (below) • Mounting VTrak in a Rack (page 17) • Installing Physical Drives (page 21) • Making Management and Data Connections (page 25) • Making Serial Cable Connections (page 40) Unpacking the VTrak The VTrak box contains the following items: • VTrak Unit • Screws for physical drives (for VTraks that ship without • Left and right mounting rails drives) • RJ11-to-DB9 serial data cable • 1.5m (4.
VTrak E-Class Product Manual Important Existing VTrak J330s, J630s, or J830s JBOD expansion units require two critical updates to support the VTrak E630f/i and E830f/i RAID subsystems: • If you have SATA physical drives, replace the existing AMUX adapters with the new SAS-to-SATA adapters, available from PROMISE Technology at http://www.promise.com • Download the latest firmware image file available from PROMISE support: http://www.promise.com/support/ and flash your existing VTrak JBOD units.
Chapter 2: Installation Mounting VTrak in a Rack Cautions • Do not install the VTrak unit into a rack without rails to support the subsystem. • Do not lay one VTrak unit on top of another. Mount each enclosure supported by its own set of rails. • Only a qualified technician who is familiar with the installation procedure should mount and install the VTrak unit. • Be sure all switches are OFF before installing the VTrak unit or exchanging components.
VTrak E-Class Product Manual Mounting rails are included with the VTrak. To install the VTrak subsystem into your rack: 1. Attach the mounting rail assemblies to the rack posts, using screws and nuts from your rack system. • The rail halves are riveted together and use no adjustment screws. • The front-left and front-right mounting rail ends are labeled. Figure 1.
Chapter 2: Installation Figure 2. Rail ends attach to the outside of each post Rail ends attach on the outside of the front and rear rack posts 2. Place the VTrak subsystem onto the rails. • At least two persons are required to safely lift the VTrak. • Lift the VTrak subsystem itself. Do not lift the VTrak by its brackets. Figure 3. Placing the VTrak subsystem onto the rack rails Brackets VTrak subsystem Rails installed and tightened 3. Secure the VTrak subsystem to the rack.
VTrak E-Class Product Manual Figure 4.
Chapter 2: Installation Installing Physical Drives If your VTrak subsystem shipped with the drives installed at the factory, you can skip this section and go to “Making Management and Data Connections” on page 25. The VTrak Ex30 RAID subsystems and JBOD expansion units support: • SAS and SATA physical drives • 2.5-inch and 3.
VTrak E-Class Product Manual Figure 5. VTrak E830f/i drive slot numbering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Figure 6. VTrak E630f/i drive slot numbering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Install all of the drive carriers into the VTrak enclosure to ensure proper airflow, even if you do not populate all the carriers with physical drives. Installing Your Drives The VTrak drive carrier accommodates 2.5-inch and 3.
Chapter 2: Installation 1. Press the drive carrier release button. The handle springs open. 2. Grasp the handle and gently pull the empty drive carrier out of the enclosure. Figure 7. Drive carrier front view 3. If you are installing SATA drives, attach a SAS-to-SATA adapter onto the power and data connectors of each drive. 4. Carefully lay the drive into the carrier with the power and data connectors facing away from the carrier handle. 5.
VTrak E-Class Product Manual 7. • Install two screws per adapter. • Snug each screw. Be careful not to over tighten. With the drive carrier handle in open position, gently slide the drive carrier into the enclosure. Important • Press the release button to push the drive carrier into position. Do not push the handle. See page 23, Figure 7. • Proper drive installation ensures adequate grounding and minimizes vibration. Always attach the drive to the carrier with four screws.
Chapter 2: Installation Making Management and Data Connections Examples of VTrak configurations include: • Fibre Channel SAN (below) • Fibre Channel DAS (page 28) • Fibre Channel with JBOD Expansion (page 30) • Fibre Channel SAN – No Single Point of Failure (page 31) • iSCSI Storage Area Network (SAN) (page 34) • iSCSI Direct Attached Storage (DAS) (page 37) • iSCSI with JBOD Expansion (page 39) Fibre Channel SAN Important For a list of supported HBAs, Switches, and SFP transceivers, download
VTrak E-Class Product Manual A Fibre Channel storage area network (SAN) requires: • An FC HBA card in each host PC or server • An SFP transceiver for each connected FC port on the subsystem • An FC switch • A network switch Data Path To establish the data path: 1. Connect FC cables between at least one FC data port on each RAID controller and the FC switch. See Figure 11. 2. Connect FC cables between the FC switch and the FC HBA cards in both host PCs or servers.
Chapter 2: Installation Management Path To establish the management path: 1. Connect Ethernet cables between the Management ports on both RAID controllers and the network switch. See Figure 12. 2. Connect Ethernet cables between the network ports on both host PCs or servers and the network switch. If you have multiple VTrak subsystems, repeat steps 1 and 2 as required. Figure 12.
VTrak E-Class Product Manual Fibre Channel DAS Important For a list of supported HBAs, switches, and SFP transceivers, download the latest compatibility list from PROMISE support: http://www.promise.com/support/. Note For multipathing (MPIO) applications, see: • “Appendix B: Multipathing on Windows” on page 363. • “Appendix C: Multipathing on Linux” on page 385.
Chapter 2: Installation Figure 13.FC DAS data and management connections Host PC or server Network switch Network cable Management ports Network connector FC HBA card FC ports FC cable VTrak RAID subsystem The VTrak RAID subsystem is shown with SFP transceivers installed. Management Path To establish the management path: 1. Connect Ethernet cables between the Management ports of both RAID controllers and the network switch. See Figure 13. 2.
VTrak E-Class Product Manual Fibre Channel with JBOD Expansion JBOD expansion requires at least one SFF-8088 4X to SFF-8088 4X external SAS cable for each JBOD unit. To add JBOD units: 1. Connect the SAS expansion port on the left controller of the RAID subsystem to the SAS data IN port on the left I/O module of the first JBOD unit. See Figure 14. 2. Connect the SAS expansion port on the right controller of the RAID subsystem to the SAS data IN port on the right I/O module of the first JBOD unit. 3.
Chapter 2: Installation Fibre Channel SAN – No Single Point of Failure Important For a list of supported HBAs, switches, and SFP transceivers, download the latest compatibility list from PROMISE support: http://www.promise.com/support/. Note For multipathing (MPIO) applications, see: • “Appendix B: Multipathing on Windows” on page 363. • “Appendix C: Multipathing on Linux” on page 385.
VTrak E-Class Product Manual Figure 15.FC SAN NSPF data connections Each RAID HBA card connects to both FC switches Each FC switch connects to: • Both Host PCs • Both RAID subsystems VTrak RAID subsystem SAS IN SAS OUT SAS IN 115200 8 N 1 SAS OUT 115200 8 N 1 VTrak JBOD unit RAID controller 1 connects to: • Both FC switches • One JBOD I/O module RAID controller 2 connects to: • Both FC switches • The other JBOD I/O module The VTrak RAID subsystem is shown with SFP transceivers installed.
Chapter 2: Installation If you have multiple VTrak subsystems, repeat steps 1 and 2 as required. Figure 16.FC SAN NSPF management connections Host PCs or Servers Network connector (motherboard or HBA) Network switch Management port on controller 2 Management port on controller 1 VTrak RAID subsystem The VTrak RAID subsystem is shown with SFP transceivers installed. JBOD Expansion JBOD connections are the same for all FC SAN and DAS configurations. See “Fibre Channel with JBOD Expansion” on page 30.
VTrak E-Class Product Manual iSCSI Storage Area Network (SAN) Important For a list of supported HBA NICs and switches, download the latest compatibility list from PROMISE support: http://www.promise.com/support/. Note For multipathing (MPIO) applications, see: • “Appendix B: Multipathing on Windows” on page 363. • “Appendix C: Multipathing on Linux” on page 385. Figure 17.
Chapter 2: Installation Data Path Each VTrak RAID controller has four (4) RJ45 iSCSI data port connectors. See page 34, Figure 17. To establish the data path: 1. Connect Ethernet cables between the iSCSI NIC in both host PCs or servers and the GbE network switch. See Figure 19. 2. Connect an Ethernet cable between at least one iSCSI data port on the left RAID controller and the GbE network switch. 3.
VTrak E-Class Product Manual Management Path Each VTrak RAID controller has one (1) Ethernet RJ45 management port connector. See page 34, Figure 17. To establish the management path: 1. Connect Ethernet cables between the network connector on both host PCs or servers and the standard network switch. See Figure 19. 2. Connect Ethernet cables between the Management port on both RAID controllers to the standard network switch. If you have multiple VTrak subsystems, repeat steps 1 and 2 as required.
Chapter 2: Installation iSCSI Direct Attached Storage (DAS) Important For a list of supported HBAs and switches, download the latest compatibility list from PROMISE support: http://www.promise.com/support/. Note For multipathing (MPIO) applications, see: • “Appendix B: Multipathing on Windows” on page 363. • “Appendix C: Multipathing on Linux” on page 385.
VTrak E-Class Product Manual Figure 20.
Chapter 2: Installation iSCSI with JBOD Expansion JBOD expansion requires at least one SFF-8088 4X to SFF-8088 4X external SAS cable for each JBOD unit. To add JBOD units: 1. Connect the SAS expansion port on the left controller of the RAID subsystem to the SAS data IN port on the left I/O module of the first JBOD unit. See Figure 14. 2. Connect the SAS expansion port on the right controller of the RAID subsystem to the SAS data IN port on the right I/O module of the first JBOD unit. 3.
VTrak E-Class Product Manual Making Serial Cable Connections Serial communication enables the terminal emulation application on your host PC or server to access the VTrak’s Command Line Interface (CLI) to set up a network connection. The VTrak package includes one RJ11-to-DB9 serial data cable for each controller. Figure 22.
Chapter 3: Setup This chapter covers the following topics: • Connecting the Power (below) • Setting-up the Serial Connection (page 44) • VTrak Default IP Addresses (page 45) • Choosing DHCP or a Static IP Address (page 45) • Setting-up VTrak with the CLI (page 47) • Setting-up VTrak with the CLU (page 55) • Logging into WebPAM PROe (page 60) • Creating Disk Arrays and Logical Drives (page 62) • Enabling LUN Mapping and Masking (page 67) • Logging out of WebPAM PROe (page 68) Connecting t
VTrak E-Class Product Manual Figure 1. Front panel LED display Power FRU Status Logical Drive Status Controller 1 Activity Controller 2 Activity Controller Heartbeat Also see the table below.
Chapter 3: Setup Drive Status Indicators The VTrak spins up the disk drives sequentially to equalize power draw during start-up. After a few moments: • The Power/Activity LED displays blue when a physical drive is present. • The Drive Status LED displays green when the physical drive is configured as a member of a disk array or as a spare. When the physical drive is unconfigured, the LED is dark. Steady means the LED is on. Blinking means a regular on/off pattern.
VTrak E-Class Product Manual Setting-up the Serial Connection The initial connection accesses the VTrak’s serial port using the serial cable connection you made. See “Making Serial Cable Connections” on page 40. Use your PC’s terminal emulation program, such as Microsoft HyperTerminal, to access the VTrak’s Command Line Interface (CLI). You can also use the serial connection to manage the VTrak through the Command Line Utility (CLU). To make the initial serial connection: 1.
Chapter 3: Setup About IP Addresses • VTrak Default IP Addresses (page 45) • Choosing DHCP or a Static IP Address (page 45) • Accessing the MAC Address in the CLI (page 46) • Accessing the MAC Address in the CLU (page 46) Choosing the appropriate IP addresses is essential to manage your VTrak subsystem over a network. You must change the VTrak’s default IP addresses as required for your environment.
VTrak E-Class Product Manual Accessing the MAC Address in the CLI To access the MAC address in the CLI: At the command prompt, type net -a list -v and press Enter. The following information displays: administrator@cli> net -a list -v ------------------------------------------------------------------------------ActiveCtrlId: 1 Port: 1 MaxSupportedSpeed: 1000Mbps LinkStatus: Up ProtocolFamily: IPv4(Enabled) IP: 10.0.0.1 IPMask: 0.0.0.0 MAC: 00:01:55:61:18:65 DNS: 0.0.0.0 Gateway: 0.0.0.
Chapter 3: Setup Setting-up VTrak with the CLI Setting up the VTrak in the CLI includes these actions: • Making Subsystem Date and Time Settings (page 47) • Virtual Management Port Settings (page 47) • • Making Virtual Management Port Settings – Automatically (page 47) • Making Virtual Management Port Settings – Manually under IPv4 (page 48) • Making Virtual Management Port Settings – Manually under IPv6 (page 49) Maintenance Mode Settings (page 50) • Making Maintenance Mode Settings – Automati
VTrak E-Class Product Manual 2. To verify the setting change, at the command prompt, type net and press Enter. The following information displays: administrator@cli> net ========================================== PF Status IP Link ========================================== IPv4 Enabled 192.168.10.85 Up IPv6 Disabled 2001::1 Up In the above example: • PF refers to IP protocol family, v4 or v6 • Status refers to whether the IP protocol is enabled. IPv4 is enabled by default.
Chapter 3: Setup MaxSupportedSpeed: 1000Mbps LinkStatus: Up ProtocolFamily: IPv4(Enabled) IP: 192.168.10.85 IPMask: 255.255.255.0 MAC: 00:01:55:61:18:65 DNS: 192.168.10.11 Gateway: 192.168.10.1 DHCP: Disabled ProtocolFamily: IPv6(Disabled) IP: 2001::1 IPMask: ffff:: MAC: 00:01:55:61:18:65 DNS: :: Gateway: :: DHCP: Disabled Making Virtual Management Port Settings – Manually under IPv6 To make IPv6 settings manually on the management port: 1.
VTrak E-Class Product Manual The following information displays: administrator@cli> net -a list -v ------------------------------------------------------------------------------ActiveCtrlId: 1 Port: 1 MaxSupportedSpeed: 1000Mbps LinkStatus: Up ProtocolFamily: IPv4(Enabled) IP: 192.168.10.85 IPMask: 255.255.255.0 MAC: 00:01:55:61:18:65 DNS: 192.168.10.11 Gateway: 192.168.10.
Chapter 3: Setup ------------------------------------------------------------------------------CtrlId: 1 Port: 1 ProtocolFamily: IPv4(Enabled) DHCP: Enabled IP: 192.168.10.94 IPMask: 255.255.255.0 MAC: 00:01:55:30:65:E9 DNS: 192.168.1.1 Gateway: 192.168.10.1 3. CtrlId: 1 ProtocolFamily: IPv6(Disabled) IP: 2001::2 IPMask: ffff:: MAC: 00:01:55:30:65:E9 DNS: :: Gateway: :: Port: 1 DHCP: Disabled CtrlId: 2 ProtocolFamily: IPv4(Enabled) IP: 10.0.0.3 IPMask: 0.0.0.0 MAC: 00:01:55:30:65:E9 DNS: 0.0.0.
VTrak E-Class Product Manual Example: administrator@cli> net -a mod -m -c 1 "primaryip=192.168.10.101, primaryipmask=255.255.255.0,primarydns=192.168.10.11,gateway=19 2.168.10.1" After a moment, the comand prompt reappears, indicating that your setting was successful. administrator@cli> 2. To verify the settings changes, at the command prompt, type net -a list -m and press Enter.
Chapter 3: Setup 3. Repeat steps 1 and 2 above but change -c 1 (controller 1) to -c 2 (controller 2). Making Maintenance Mode Settings – Manually under IPv6 You make these settings for one controller at a time. To make maintenance mode settings: 1. At the command prompt, type net -a enable -f ipv6 -m -c 1 and press Enter to enable IPv6. After a moment, the comand prompt reappears, indicating that your setting was successful. administrator@cli> 2.
VTrak E-Class Product Manual CtrlId: 1 Port: 1 ProtocolFamily: IPv6(Enabled) DHCP: Disabled IP: 2001:0db8:85a3:0000:0000:8a2e:0370:7336 IPMask: 001:0db8:fedc:ba98:7654:3210:0246:8acf MAC: 00:01:55:30:65:E9 DNS: 2001:0db8:85a3:0000:0000:8a2e:0370:7001 Gateway: 2001:0db8:85a3:0000:0000:8a2e:0370:7002 CtrlId: 2 Port: 1 ProtocolFamily: IPv4(Enabled) IP: 10.0.0.3 IPMask: 0.0.0.0 MAC: 00:01:55:30:65:E9 DNS: 0.0.0.0 Gateway: 0.0.0.
Chapter 3: Setup Setting-up VTrak with the CLU Setting up the VTrak in the CLU includes these actions: • Accessing the CLU Quick Setup Menu (page 55) • Making Subsystem Date and Time Settings (page 56) • Virtual Management Port Settings (page 56) • • • Making Virtual Management Port Settings – Automatically (page 56) • Viewing Virtual Management Port Settings (page 56) • Making Virtual Management Port Settings – Manually under IPv4 (page 57) • Making Virtual Management Port Settings – Manual
VTrak E-Class Product Manual 2. Highlight Quick Setup and press Enter. The first Quick Setup screen enables you to make Date and Time settings. Making Subsystem Date and Time Settings To set the subsystem date and time: 1. Press the arrow keys to highlight System Date. 2. Press the backspace key to erase the current date. 3. Type the new date. 4. Follow the same procedure to set the System Time. 5. Press Control-A to save these settings and move to the Management Port settings screen.
Chapter 3: Setup Making Virtual Management Port Settings – Manually under IPv4 To make IPv4 settings manually on the management port: 1. Press the arrow keys to highlight IP Address. 2. Press the backspace key to erase the current IP address. 3. Type the new Management Port IP address. 4. Follow the same procedure to specify the Subnet Mask, Gateway IP Address and DNS Server IP Address. If you do not have a DNS server, skip the DNS Server IP address. 5.
VTrak E-Class Product Manual To enable automatic maintenance mode settings: 1. From the CLU Main Menu, highlight Network Management and press Enter. 2. Highlight Maintenance Mode Network Configuration and press Enter. 3. Highlight the controller you want and press Enter. 4. Highlight DHCP and press the spacebar to toggle to Enabled. 5. Press Control-A to save your settings and move to the Maintenance Mode IPv6 settings screen.
Chapter 3: Setup • If you made settings for Controller 2, move to the RAID Configuration menu. Note If you want to configure your RAID system now, using the CLU, see “Managing Disk Arrays” on page 229 for information about your choices. Exiting the CLU To exit the CLU from the Quick Setup RAID Configuration menu: 1. Highlight Skip the Step and Finish and press Enter. 2. Highlight Return to CLI and press Enter. This completes management port and maintenance mode setup.
VTrak E-Class Product Manual Logging into WebPAM PROe 1. Launch your browser. 2. In the browser address field, type in the virtual management port IP address of the VTrak subsystem. Use the virtual management port IP address you set in the CLI (page 47) or CLU (page 55). Example: • WebPAM PROe uses a secure HTTP connection . . . . . . . . . .https:// • Enter the IP address of the VTrak . . . . . . . . . . . . . . . 192.168.10.85 Together, your entry looks like this: https://192.168.10.85 3.
Chapter 3: Setup Important PROMISE recommends that you change the Administrator’s default password immediately after setup is completed. See “Changing User Passwords” on page 105 or page 288. Note Make a Bookmark (Firefox) or set a Favorite (Internet Explorer) of the Login Screen so you can access it easily next time. After log-in, the WebPAM PROe opens with the Dashboard tab. See page 61, Figure 5. Figure 5.
VTrak E-Class Product Manual Creating Disk Arrays and Logical Drives On a newly activated RAID system, there are no disk arrays or logical drives. The term “disk array” includes arrays composed of solid state drives. To create your disk arrays and logical drives: 1. Click the Storage tab, then click the Wizard option. Or, click Disk Array under System Status. The Wizard screen appears with three creation alternatives: 2.
Chapter 3: Setup Optimal Configurations When you choose the Optimal Configurations option, you choose a script designed to set up your disk arrays, logical drives, and spare drives for a specific target application. Each script requires a specific model of RAID subsystem. And most scripts require a specific model and number of JBOD expansion units. You cannot cannot modify these scripts.
VTrak E-Class Product Manual • Mixing SATA/SAS Drive – Check this box if you want to use both SATA and SAS drives in the same disk array If the box is unchecked, and you have both SATA and SAS drives, different arrays are created for each type of drive. 2. In the Number of Logical Drives field, enter the number of logical drives you want to make from this disk array. VTrak supports up to 32 logical drives per disk array. 3.
Chapter 3: Setup Look for drives with a green LED dark, a blue LED lit, and no crosshatching over the carrier. 3. Click a physical drive to select it for your array. The physical drive’s ID number is added to the Selected list. 4. Click the Next button to continue. The Create Logical Drive screen appears. Step 2 – Logical Drive Creation 1. Enter your information and choose your options. • Enter a logical drive alias in the field provided. • Choose a RAID level from the dropdown menu.
VTrak E-Class Product Manual 2. 3. Click the enclosure graphic to view information about physical drives. Click a physical drive to select it for your spare drive. The physical drive’s ID number is added to the Selected list. 4. Click the Next button to continue. The Summary screen appears. Step 4 – Summary The Summary screen lists the disk arrays, logical drives, and spare drives that you specified. If you accept these parameters, click the Submit button.
Chapter 3: Setup Enabling LUN Mapping and Masking These features are optional for each logical drive. The Enable LUN Mapping dialog box appears after you create a logical drive. To enable LUN Mapping: 1. Click the OK button in the Enable LUN Mapping dialog box. The LUN Mapping & Masking screen appears. 2. Check the Enable LUN Masking box to enable LUN Masking. 3. Click the LUN Mapping button to continue. The initiator list screen displays. 4.
VTrak E-Class Product Manual Logging out of WebPAM PROe There are two ways to log out of WebPAM PROe: • Close your browser window • Click Logout on the WebPAM PROe banner Figure 7. Clicking “Logout” on the WebPAM PROe banner Clicking Logout brings you back to the Login Screen. See page 60. After logging out, you must enter your user name and password in order to log in again. Using WebPAM PROe over the Internet The above instructions cover connections between VTrak and your company network.
Chapter 4: Management with WebPAM PROe This chapter contains the following topics: • Logging into WebPAM PROe (below) • Choosing the Display Language (page 70) • Perusing the Interface (page 72) • Logging out of WebPAM PROe (page 74) • Viewing the Storage Network (page 75) • Managing Subsystems (page 76) • Managing RAID Controllers (page 85) • Managing Enclosures (page 92) • Managing UPS Units (page 96) • Managing Network Connections (page 100) • Managing Users (page 102) • Managing L
VTrak E-Class Product Manual Together, your entry looks like this: https://192.168.10.85 3. When the login screen appears: • Type administrator in the User Name field. • Type password in the Password field. • Click the Login button. The User Name and Password are case sensitive. 4. Optional. Choose a display language from the dropdown menu. WebPAM PROe displays in English, German, French, Italian, Spanish, Russian, Japanese, Traditional Chinese, Simplified Chinese, and Korean. 5.
Chapter 4: Management with WebPAM PROe If you are already logged in and you want to change the display language: 1. Click Logout at the top right corner of the screen. The Login screen appears. 2. Click the Language dropdown menu and highlight the language you prefer. 3. Reenter your user name and password. 4. Click the Login button. WebPAM PROe opens in the language you chose.
VTrak E-Class Product Manual Perusing the Interface The WebPAM PROe interface consists of a header and four tabs, each with specific functions.
Chapter 4: Management with WebPAM PROe • Administration tab • Subsystem settings, clearing statistics, NTP, and controller lock • User management, including LDAP and role mapping • Software services • Runtime and NVRAM event logs • Background activity, settings and schedules • Firmware updates • Image version • Performance monitor • PSU wattage monitor • Restore factory default settings • Import/Export user database and configuration script • Network management 73
VTrak E-Class Product Manual Logging out of WebPAM PROe There are two ways to log out of WebPAM PROe: • Close your browser window • Click Logout on the WebPAM PROe banner Figure 2. Clicking “Logout” on the WebPAM PROe banner Clicking Logout brings you back to the Login Screen. See page 70. After logging out, you must enter your user name and password in order to log in again.
Chapter 4: Management with WebPAM PROe Viewing the Storage Network To view the other subsystems on your Storage Network, click the Discovery tab at the left edge of the WebPAM PROe window. Logging onto a Subsystem To log onto a subsystem in the list, double-click the subsystem. Caution The new subsystem displays in the same browser tab. Click your browser’s back button to return to the original subsystem.
VTrak E-Class Product Manual Managing Subsystems Subsystem management includes: • Viewing Subsystem Information (below) • Making Subsystem Settings (page 77) • Locking or Unlocking the Subsystem (page 77) • Restoring Factory Default Settings (page 78) • Clearing Statistics (page 79) • Saving a Service Report (page 79) • Importing a Configuration Script (page 82) • Exporting a Configuration Script (page 82) • Restarting the Subsystem (page 83) • Shutting Down the Subsystem (page 83) • R
Chapter 4: Management with WebPAM PROe Making Subsystem Settings To make subsystem settings: 1. Click the Administration tab. 2. Click the Subsystem Information icon. 3. Click the Settings button. 4. Make changes as required: • Enter an alias or change the existing alias in the field provided. • Choose a redundancy type from the dropdown menu. The choices are Active-Active and Active-Standby • 5. Check the box to enable Cache Mirroring. Click the Save button.
VTrak E-Class Product Manual Releasing the Lock To release a lock that you set: 1. Click the Administration tab. 2. Click the Subsystem Information icon. 3. Click the Lock/Unlock button. 4. Click the Unlock button. Releasing a Lock set by another user To release somebody else’s lock: 1. Click the Administration tab. 2. Click the Subsystem Information icon. 3. Click the Lock/Unlock button. 4. Check the Force Unlock box. 5. Click the Unlock button.
Chapter 4: Management with WebPAM PROe Firmware Factory Default Settings Software Factory Default Settings • Background activity settings • BGA scheduler settings • Controller settings • Service settings • Enclosure settings • Webserver settings • FC port settings • SNMP settings • iSCSI port settings • Telnet settings • Management network settings • SSH settings • Physical drive settings • Email settings • Subsystem settings • Netsend settings • CIM settings • NTP settin
VTrak E-Class Product Manual Information for the report is gathered and compiled. This action takes up to a few minutes, depending on the size of your RAID system 2. Click the Save File option, then click the Save button. The report saves to your Host PC as a compressed HTML file. 3. Double-click the downloaded file to decompress it. 4. Double-click the report to open it in your default browser.
Chapter 4: Management with WebPAM PROe • Lunmap Info – LUN map type, LUN masking status, and LUN entries • Network Info – Virtual port • Network Maintenance Info – Maintenance mode ports • Phydriv Info – Basic physical drive information • Phydriv Verbose Info – Full physical drive information • PD SMART Info – Physical drive ID, model, type, and SMART status • PSU Wattage Info – Enclosure power consumption, power supply input and output, and power on time • SWMGT Info – Software management
VTrak E-Class Product Manual Importing a Configuration Script You can write a CLI configuration script to automatically configure your VTrak subsystem. The script must be a plain, non-encrypted text file. From there, you can import the script from the Host PC and perform the configuration automatically. Cautions • Do NOT attempt to write or modify a configuration script until you receive guidance from Technical Support. See page 435.
Chapter 4: Management with WebPAM PROe 5. 6. Click the Submit button. In the Open dialog box, click the Save File option, then click the OK button. The file is saved to your PC as “Configscript.txt”. Caution Do NOT attempt to write or modify a configuration script until you receive guidance from Technical Support. See page 435. Restarting the Subsystem This function shuts down the subsystem and then restarts it.
VTrak E-Class Product Manual 6. Click the Confirm button. When the controller shuts down, your WebPAM PROe connection is lost. 7. Wait no less than two minutes. 8. Manually turn OFF the switches on both power supplies. Important If your RAID subsystem manages JBOD expansion units, you must follow the proper startup procedure. Restarting the Subsystem after a Shutdown Important If your RAID subsystem manages JBOD expansion units, always power on the JBOD expansion units first.
Chapter 4: Management with WebPAM PROe Managing RAID Controllers RAID controller management includes: • Viewing Controller Information (below) • Making Controller Settings (page 86) • Viewing Controller Statistics (page 87) • Locating a Controller (page 88) • Viewing the Flash Image Information (page 88) • Updating Firmware on a RAID Subsystem (page 89) • Viewing Battery Information (page 89) • Reconditioning a Battery (page 90) • Making Buzzer Settings (page 91) • Silencing the Buzzer (
VTrak E-Class Product Manual Advanced controller information includes: • Slot 1 Memory Type • Slot 1 Memory Size • Slot 2 Memory Type • Slot 2 Memory Size • LUN Affinity * • ALUA * • Controller Role • Flash Type • Flash Size • NVRAM Type • NVRAM Size • Preferred Cache Line Size • Coercion * • Coercion Method * • SMART * • SMART Polling Interval * • Write Back Cache Flush Interval * • Enclosure Polling Interval * • Host Cache Flushing * • Adaptive Writeback Cache * •
Chapter 4: Management with WebPAM PROe • HDD Power Saving – Choose time periods from the dropdown menus. After an HDD has been idle for the set period of time: • 5. Power Saving Idle Time – Parks the read/write heads. • Power Saving Standby Time – Lowers disk rotation speed. • Power Saving Stopped Time – Spins down the disk (stops rotation). • Coercion – Check the box to enable or uncheck to disable.
VTrak E-Class Product Manual Controller statistics include: • Data Transferred • IO Requests • Read Data Transferred • Non-Read/Write Requests • Write Data Transferred • Read IO Requests • Errors • Write IO Requests • Non-Read/Write Errors • Statistics Start date and time • Read Errors • • Write Errors Statistics Collection date and time Note To clear controller statistics, see “Clearing Statistics” on page 79.
Chapter 4: Management with WebPAM PROe RAID subsystems have the following components in their flash image: • Kernel • BIOS • Firmware • 6G Expander • Software • System Libraries • Ramdisk • Applications • SEP Firmware • Mount Scripts • OEM Customization • PLX EEPROM Image • Running – The version that is currently running on the subsystem or expansion unit. • Flashed – This version was updated but does not run until the subsystem restarts.
VTrak E-Class Product Manual • Temperature threshold discharge – Maximum temperature allowed when the battery is discharging • Temperature threshold charge – Maximum temperature allowed when the battery is charging • Battery temperature – Actual battery temperature • Cycle count – Number of times the battery was reconditioned • Voltage in millivolts • Current in milliamps Reconditioning a Battery Batteries maintain power to the controller cache in the event of a power failure, thus protecting a
Chapter 4: Management with WebPAM PROe 5. 6. Make settings changes as required: • Start Time • Uncheck the Enable This Schedule box to disable this activity. • Recurrence Pattern • Start From • End On Click the Save button to apply the new settings. Making Buzzer Settings To make buzzer settings: 1. Click the Device tab. 2. Click the Component List icon. 3. Click the Buzzer and click the Settings button. 4. Check the Enable Buzzer box to enable the buzzer. Or uncheck the box to disable.
VTrak E-Class Product Manual Managing Enclosures Enclosure management includes the following functions: • Viewing the Enclosures Summary (page 92) • Making Enclosure Settings (page 93) • Locating an Enclosure (page 93) • Viewing FRU VPD Information (page 94) • Viewing Power Supply Status (page 94) • Viewing Fan Status (page 94) • Viewing Temperature Sensor Status (page 95) • Viewing Voltage Sensor Status (page 95) Viewing Enclosure Topology This feature displays the connection topology of t
Chapter 4: Management with WebPAM PROe Locating an Enclosure To locate an enclosure: 1. Click the Device tab. 2. Click the Component List icon. 3. Click the enclosure you want, then click the Locate button. The enclosure LEDs blink for one minute. Viewing Enclosure Information To view enclosure information: 1. Click the Device tab. 2. Click the Component List icon. 3. Click the Enclosure and click the View button.
VTrak E-Class Product Manual Enclosure settings include: • Enclosure Warning Temperature Threshold • Enclosure Critical Temperature Threshold • Controller Warning Temperature Threshold • Controller Critical Temperature Threshold 4. In the field provided, type the temperature in degrees C for each threshold value. 5. Click the Save button. Viewing FRU VPD Information FRU VPD refers to Vital Product Data (VPD) information about Field Replaceable Units (FRU) in the enclosure.
Chapter 4: Management with WebPAM PROe 2. Click the Component List icon. 3. Click the Enclosure and click the View button. 4. Scroll down to view the Fans. The screen displays the status and speed of the fans on the power supplies. If fan speed is below the Healthy Threshold, there is a malfunction. See “Diagnosing an Enclosure Problem” on page 391. Viewing Temperature Sensor Status To view the status of the temperature sensors: 1. Click the Device tab. 2. Click the Component List icon. 3.
VTrak E-Class Product Manual Managing UPS Units Uninterruptible Power Supply (UPS) Management includes the following functions: • Viewing a List of UPS Units (below) • Making UPS Settings (page 97) • Viewing UPS Information (page 98) Viewing a List of UPS Units To view a list of UPS units supporting the VTrak: 1. 2. Click the Device tab. Click the UPS icon. Information in the UPS List includes: • ID – The ID number of the UPS • Status – OK means Normal.
Chapter 4: Management with WebPAM PROe Making UPS Settings These settings control how the VTrak subsystem detects the UPS unit and responds to data reported by the UPS unit. To make UPS settings: 1. Click the Device tab. 2. Click the UPS icon. 3. Click the UPS Settings button. 4. Perform the following actions as required: • • • • 5. Verify the Current UPS Communication method. See Note 1: • SNMP – Network connection. • Serial – Serial connection. • Unknown – No connection.
VTrak E-Class Product Manual Viewing UPS Information To view information about a specific UPS unit: 1. Click the Device tab. 2. Click the UPS icon. 3. Mouse-over UPS and click the View button. UPS information includes: • UPS ID • Model Name • Serial Number • Firmware Version • Manufacture Date • Voltage Rating – Output voltage of the UPS. • Battery Capacity – Backup capacity expressed as a percentage.
Chapter 4: Management with WebPAM PROe Note The maximum recommended Loading Ratio varies among models of UPS units. The general range is 60% to 80%. If the reported Loading Ratio exceeds the recommended value for your UPS unit: • Have fewer subsystems or peripherals connected to this UPS unit. • Add more UPS units, or use a higher-capacity UPS unit, to protect your RAID systems.
VTrak E-Class Product Manual Managing Network Connections Network Connections Management includes the following functions: • Making Virtual Management Port Settings (page 100) • Making Maintenance Mode Settings (page 100) Making Virtual Management Port Settings The VTrak subsystem has a virtual management port, enabling you to log into a VTrak with dual controllers using one IP address. Before you change settings, please see “About IP Addresses” on page 45.
Chapter 4: Management with WebPAM PROe To make maintenance mode settings: 1. Click the Device tab. 2. Click the Network Management icon. 3. Click the Maintenance Mode tab. 4. Click the controller and protocol family whose settings you want to change and click the Configuration button. 5. 6. Make the following settings are needed: • Check the Enable box to enable this protocol family. • Check the Enable DHCP box to enable a DHCP server to make your network settings.
VTrak E-Class Product Manual Managing Users User management includes: • Viewing User Information (below) • Creating a User (page 102) • Setting User Event Subscriptions (page 103) • Changing User Passwords (page 105) • Deleting a User (page 106) • Importing a User Database (page 106) • Exporting a User Database (page 107) The Administrator or a Super User can perform these tasks. Viewing User Information To view user information: 1. Click the Administration tab. 2.
Chapter 4: Management with WebPAM PROe 5. Choose a privilege level from the dropdown menu. See the table below. 6. 7. (Optional) Uncheck the Enable box to disable this User account. Click the Save button. The user is added to the list. Important • For this user to receive event notification, Click the new user and click the Subscription button. • For this user to be an LDAP User, click the LDAP Settings button, enter information and make settings as required.
VTrak E-Class Product Manual Subscribing users receive notification of events at the chosen severity level and all higher levels. See the table on the next page. Note Each user must have a valid Email address to receive events. See “Making User Settings” below. Changing a user subscription requires Administrator or Super User privileges. To set a user event subscription: 1. Click the Administration tab. 2. Click the User Management icon. 3.
Chapter 4: Management with WebPAM PROe User Privileges Level Meaning View Allows the user to see all status and settings but not to make any changes Maintenance Allows the user to perform maintenance tasks including Rebuilding, PDM, Media Patrol, and Redundancy Check Power Allows the user to create (but not delete) disk arrays and logical drives, change RAID levels, change stripe size; change settings of components such as disk arrays, logical drives, physical drives, and the controller Super Allo
VTrak E-Class Product Manual Deleting a User This action requires Administrator or Super User privileges. Note You cannot delete the Administrator. To delete a user: 1. Click the Administration tab. 2. Click the User Management icon. 3. In the User list, Click the user you want, then click the Delete button. 4. In the Confirmation box, type the word “confirm” in the field provided and click the Confirm button.
Chapter 4: Management with WebPAM PROe Exporting a User Database You can save the user information and settings from one VTrak RAID subsystem, export it, and then import it to automatically configure your other VTrak RAID subsystems. To export a user database: 1. Click the Administration tab. 2. Click the Import/Export icon. 3. Click the Export option. 4. Choose User Database from the Type dropdown menu. 5. Click the Submit button. 6.
VTrak E-Class Product Manual Managing LDAP LDAP Management includes the following functions: • Viewing LDAP Information (page 108) • Making LDAP Settings (page 109) • Testing LDAP Settings (page 111) • Viewing a List of Role Maps (page 111) • Adding a Role Map (page 111) • Making Role Map Settings (page 112) • Deleting a Role Map (page 113) Viewing LDAP Information Lightweight Directory Access Protocol (LDAP) is a protocol used to access a directory listings. To view LDAP information: 1.
Chapter 4: Management with WebPAM PROe • Object Class – For email notification. The default is person. • Full Name Attribute – Stores user’s full name in LDAP server. displayName is the default. • Email Address Attribute – Stores user’s email address in LDAP server. mail is the default. • Privilege for LDAP Users – Default Privilege or Using Role Mapping. • Default Privilege – Applies to Default Role Policy. View, Maintenance, Power, or Super.
VTrak E-Class Product Manual 5. • Email notification for Event – Check the box to enable an email subscription for an LDAP authenticated user. • Object Class – For email notification. The default is person. • Full Name Attribute – Store user's full name in LDAP server. displayName is the default. • Email Address Attribute – Store user's email address in LDAP server. mail is the default. • Privilege for LDAP Users – Choose Using Default Privilege or Using Role Mapping. See the table below.
Chapter 4: Management with WebPAM PROe Testing LDAP Settings To test your LDAP settings: 1. 2. From the Main Menu, highlight Additional Info and Management and press Enter. Highlight LDAP Management and press Enter. The LDAP Settings screen appears. 3. Highlight LDAP Auth and press Enter. The LDAP Authorization screen appears. LDAP must be enabled to test the settings. 4. Highlight Test and press Enter. Viewing a List of Role Maps A Role Map is a method of mapping a group of users to an LDAP server.
VTrak E-Class Product Manual Group names are for convenience only. A group name does not impose any role or limitation upon the group it represents. You can have multiple groups but each must have a different name. 7. 8. From the Subsystem Privilege dropdown menu, choose a privilege level. See the table below. Click the Submit button. The new Role Map is added to the list.
Chapter 4: Management with WebPAM PROe Deleting a Role Map To delete a role map: 1. Click the Administration tab. 2. Click the User Management icon. 3. Click the LDAP Settings button. 4. Click the Role Mapping button. 5. Click a Role Map in the list (under LDAP Role and Subsystem Privilege) and click the Delete button. 6. Click the Confirm button. The Role Map is deleted from the list.
VTrak E-Class Product Manual Managing Background Activities Background activity management includes: • Viewing Current Background Activities (page 114) • Viewing Scheduled Background Activities (page 114) • Adding a Scheduled Background Activity (page 115) • Changing a Background Activity Schedule (page 116) • Enabling or Disabling a Scheduled Background Activity (page 117) • Deleting a Scheduled Background Activity (page 117) • Media Patrol (page 118) • Redundancy Check (page 118) • Initi
Chapter 4: Management with WebPAM PROe 2. Click the Background Activities icon. The list of background appears. 3. Click the Scheduler button. The list of currently scheduled background activities appears. Adding a Scheduled Background Activity To add a new scheduled background activity: 1. Click the Administration tab. 2. Click the Background Activities icon. The list of background appears. 3. Click the Scheduler button. The list of currently scheduled background act it viti es appears. 4. 5.
VTrak E-Class Product Manual • Until date from the dropdown menus. 12. For Redundancy Check, choose, • Auto Fix option – Attempts to repair the problem when it finds an error. Check to enable • Pause on Error option – The process stops when it finds a nonrepairable error. Check to enable • Select LD – Check the boxes for the logical drives to run Redundancy Check. Check at least one logical drive 13. Click the Save button.
Chapter 4: Management with WebPAM PROe • • 6. Until date from the dropdown menus. For Redundancy Check, choose, • Auto Fix option – Attempts to repair the problem when it finds an error. Check to enable • Pause on Error option – The process stops when it finds a nonrepairable error. Check to enable • Select LD – Check the boxes for the logical drives to run Redundancy Check. Check at least one logical drive Click the Save button.
VTrak E-Class Product Manual 2. Click the Background Activities icon. The list of background appears. 3. Click the Scheduler button. The list of currently scheduled background act it viti es appears. 4. Click the background activity and click the Delete button. 5. In the confirmation box, click the confirm button. Media Patrol Media Patrol is a routine maintenance procedure that checks the magnetic media on each disk drive.
Chapter 4: Management with WebPAM PROe 3. 4. 5. Click the Settings button. Click the Redundancy Check Rate dropdown menu and choose a rate: • Low – Fewer system resources to Redundancy Check, more to data read/write operations. • Medium – Balances system resources between Redundancy Check and data read/write operations. • High – More system resources to Redundancy Check, fewer to data read/write operations. Click the Confirm button.
VTrak E-Class Product Manual Rebuild When you rebuild a disk array, you are actually rebuilding the data on one physical drive. • When a physical drive in a disk array fails and a spare drive of adequate capacity is available, the disk array begins to rebuild automatically using the spare drive.
Chapter 4: Management with WebPAM PROe See “Migrating a Logical Drive’s RAID Level” on page 169 and “RAID Level Migration” on page 347. Making Migration Settings To make migration settings: 1. Click the Administration tab. 2. Click the Background Activities icon. The list of background activities appears. 3. 4. 5. Click the Settings button. Click the Migration Rate dropdown menu and choose a rate: • Low – Fewer system resources to Migration, more to data read/write operations.
VTrak E-Class Product Manual • • High – More system resources to PDM, fewer to data read/write operations. Highlight the current values in the block threshold fields and input new values. Reassigned block threshold range is 1 to 512 blocks. Error block threshold range is 1 to 2048 blocks. 5. Click the Confirm button. Transition Transition is the process of replacing a revertible spare drive that is currently part of a disk array with an unconfigured physical drive or a non-revertible spare drive.
Chapter 4: Management with WebPAM PROe Making Synchronization Settings To make Synchronization settings: 1. Click the Administration tab. 2. Click the Background Activities icon. The list of background activities appears. 3. 4. 5. Click the Settings button. Click the Synchronization Rate dropdown menu and choose a rate: • Low – Fewer system resources to Synchronization, more to data read/ write operations. • Medium – Balances system resources between Synchronization and data read/write operations.
VTrak E-Class Product Manual Managing Storage Services Storage service management includes: • Viewing a List of Services (below) • Email Service (page 124) • SLP Service (page 125) • Webserver Service (page 126) • Telnet Service (page 127) • SSH Service (page 128) • SNMP Service (page 129) • CIM Service (page 131) • Netsend Service (page 132) Viewing a List of Services This feature displays all software services running on the RAID subsystem. See the table below.
Chapter 4: Management with WebPAM PROe Restarting Email Service To restart the Email service: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the Email service and click the Restart button. Making Email Settings To change Email service settings: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the Email service and click the Settings button. 4.
VTrak E-Class Product Manual Stopping SLP Service To stop the SLP service: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the SLP service and click the Stop button. 4. Click the Confirm button. To start the SLP service after stopping it: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the SLP service and click the Start button. Restarting SLP Service To restart the SLP service: 1. Click the Administration tab. 2. Click the Services icon. 3.
Chapter 4: Management with WebPAM PROe 4. Click the Confirm button. To start the Webserver service after stopping it: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the Webserver service and click the Start button. Restarting Webserver Service 1. Click the Administration tab. 2. Click the Services icon. 3. Click the Webserver service and click the Restart button. Making Webserver Settings To change Webserver service settings: 1. Click the Administration tab. 2.
VTrak E-Class Product Manual 3. Click the Telnet service and click the Start button. Restarting Telnet Service To restart the Telnet service: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the Telnet service and click the Restart button. Making Telnet Settings To change Telnet service settings: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the Telnet service and click the Settings button. 4.
Chapter 4: Management with WebPAM PROe 3. Click the SSH service and click the Start button. Restarting SSH Service To restart the SSH service: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the SSH service and click the Restart button. Making SSH Settings To change SSH service settings: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the SSH service and click the Settings button. 4.
VTrak E-Class Product Manual 3. Click the SNMP service and click the Start button. Restarting SNMP Service To restart the SNMP service: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the SNMP service and click the Restart button. Making SNMP Settings To change SNMP service settings: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the SNMP service and click the Settings button. 4.
Chapter 4: Management with WebPAM PROe Event Severity Levels Level Description Fatal Non-recoverable error or failure has occurred. Critical Action is needed now and the implications of the condition are serious. Major Action is needed now. Minor Action is needed but the condition is not a serious at this time. Warning User can decide whether or not action is required. Information Information only, no action is required. Deleting an SNMP Trap Sink To delete a trap sink: 1.
VTrak E-Class Product Manual Restarting CIM Service To restart the CIM service: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the CIM service and click the Restart button. Making CIM Settings To change CIM service settings: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the CIM service and click the Settings button. 4. Make settings changes as required: • Choose a startup type, • Automatic – (default) Starts and runs with the subsystem.
Chapter 4: Management with WebPAM PROe Starting Netsend Service To restart the Netsend service: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the Netsend service and click the Start button. Stopping Netsend To stop the Netsend service: 1. Click the Administration tab. 2. Click the Services icon. 3. Click the Netsend service and click the Stop button. 4. Click the Confirm button. Restarting Netsend Service To start the Netsend service after stopping it: 1.
VTrak E-Class Product Manual 6. Click the Add button. The recipient server is added to the list. 7. Click the Save button. 8. Click the Confirm button. Event Severity Levels Level Description Fatal Non-recoverable error or failure has occurred. Critical Action is needed now and the implications of the condition are serious. Major Action is needed now. Minor Action is needed but the condition is not a serious at this time. Warning User can decide whether or not action is required.
Chapter 4: Management with WebPAM PROe Working with the Event Viewer Working with the Event Viewer includes the following functions: • Viewing Runtime Events (page 135) • Saving Runtime Events (page 136) • Clearing Runtime Events (page 136) • Viewing NVRAM Events (page 136) • Saving NVRAM Events (page 137) • Clearing NVRAM Events (page 137) The Event Viewer displays log of subsystem events.
VTrak E-Class Product Manual 3. • Timestamp – Date and time the event happened. • Description – A description of the event in plain language. Press the up and down arrow keys to scroll through the log. Saving Runtime Events This feature saves a plain text file of runtime events to your host PC or server using your browser. To save the Runtime Events log: 1. Click the Administration tab. 2. Click the Events icon. 3. Click the Save button. 4.
Chapter 4: Management with WebPAM PROe • 4. Description – A description of the event in plain language. Press the up and down arrow keys to scroll through the log. Saving NVRAM Events This feature saves a plain text file of NVRAM events to your host PC or server using your browser. To save NVRAM Events: 1. Click the Administration tab. 2. Click the Events icon. 3. Click the NVRAM Events button. 4. Click the Save button. 5.
VTrak E-Class Product Manual Monitoring Performance Performance monitoring includes: • Monitoring I/O Performance (below) • Monitoring PSU Wattage (page 139) Monitoring I/O Performance The Performance Monitor displays real-time performance statistics for logical drives, physical drives, and Fibre Channel or iSCSI data ports. The vertical scale adjusts dynamically to accommodate the statistical data.
Chapter 4: Management with WebPAM PROe 6. 7. 8. Click the Select Physical Drives button and check the boxes for the physical drives you want to see. • Total of all physical drives • Up to 8 individual physical drives Under Port, choose the metric you want to see from the Measurement dropdown menu.
VTrak E-Class Product Manual 4. 5. • Average latency in ms • Minimum latency in ms • I/Os per second Click the Select Logical Drives button and check the boxes for the logical drives you want to see. • Total of all logical drives • Up to 8 individual logical drives Under Input Power of an individual Enclosure, click the Select Enclosures button and check the boxes for the enclosures you want to see.
Chapter 4: Management with WebPAM PROe Managing Physical Drives Physical drive management includes: • Viewing a List of Physical Drives (below) • Viewing Physical Drive Information (page 141) • Making Global Physical Drive Settings (page 143) • Making Individual Physical Drive Settings (page 144) • Viewing Physical Drive Statistics (page 144) • Viewing Physical Drive SMART Log Information (page 145) • Saving the Physical Drive SMART Log (page 145) • Locating a Physical Drive (page 146) • F
VTrak E-Class Product Manual 2. 3. Click the Physical Drive icon. Click the physical drive you want, then click the View button.
Chapter 4: Management with WebPAM PROe • Drive Reference Temperature Advanced information for SAS physical drives includes: • Read Cache – Enabled or disabled • Read Cache Support – Yes or No • Write Cache – Enabled or disabled • Write Cache Support – Yes or No • Enable Read Look Ahead Support – Yes or No • Read Look Ahead Cache – Enabled or disabled • Command Queuing – Enabled or disabled • Command Queuing Support – Yes or No • WWN – Worldwide Number • Port 1 Negotiated Physical Drive
VTrak E-Class Product Manual • 5. Enable Read Cache Click the Save button. Making Individual Physical Drive Settings To make individual physical drive settings: 1. Click the Device tab. 2. Click the Physical Drive icon. 3. Click the physical drive you want, then click the Settings button. 4. On the Settings tab: • 5. On the SMART Log Settings tab: • 6. Enter, change, or delete the alias in the Alias field. Check the box to enable the SMART log. Click the Save button.
Chapter 4: Management with WebPAM PROe • Avg Response Time Ctrl 2 – Controller 2 average response time • Max Response Time Ctrl 1 – Controller 1 maximum response time • Max Response Time Ctrl 2 – Controller 2 maximum response time To clear physical drive statistics, see “Clearing Statistics” on page 79. Viewing Physical Drive SMART Log Information To view physical drive SMART Log information: 1. Click the Device tab. 2. Click the Physical Drive icon. 3.
VTrak E-Class Product Manual 5. Click the Save Advanced SMART Log button. Your browser saves a text file containing the SMART Log to its designated download folder. Locating a Physical Drive This feature causes the drive carrier LEDs to blink for one minute to assist you in locating the physical drive, and is supported by RAID subsystems and JBOD expansion units. To locate a physical drive: 1. Click the Device tab. 2. Click the Physical Drive icon. 3.
Chapter 4: Management with WebPAM PROe 4. Mouse over the physical drive you want to force offline. 5. Click the Force Offline button. 6. In the Confirmation box, type the word “confirm” in the field provided and click the Confirm button. Clearing a Stale or a PFA Condition Stale – The physical drive contains obsolete disk array information. PFA – The physical drive has errors resulting in a prediction of failure.
VTrak E-Class Product Manual Managing Disk Arrays Disk array management includes: • Viewing a List of Disk Arrays (below) • Viewing Disk Array Information (page 148) • Creating a Disk Array Manually (page 150) • Creating a Disk Array with the Wizard (page 151) • Deleting a Disk Array (page 156) • Making Disk Array Settings (page 157) • Locating a Disk Array (page 158) • Running Media Patrol on a Disk Array (page 158) • Running PDM on a Disk Array (page 159) • Preparing a Disk Array for T
Chapter 4: Management with WebPAM PROe The list of disk arrays appears. 3. Click the disk array you want, then click the View button. Array information displays, including: • ID – DA0, DA1, DA2, etc.
VTrak E-Class Product Manual Creating a Disk Array Manually This feature creates a disk array only. You can also use the Wizard to create a disk array with logical drives and spare drives at the same time. This action requires Super User or Power User privileges. To create a disk array: 1. Click the Storage tab. 2. Click the Disk Array icon. 3. Click the Create Disk Array button. 4.
Chapter 4: Management with WebPAM PROe Creating a Disk Array with the Wizard The Wizard creates disk arrays and logical drives automatically. It has four options. • Optimal Configurations – You choose a script designed to set up your disk arrays, logical drives, and spare drives for a specific target application. Each script requires a specific model of RAID subsystem. And most scripts require a specific model and number of JBOD expansion units. You cannot cannot modify these scripts.
VTrak E-Class Product Manual Wizard: Optimal Configurations Important Know how your RAID system is configured so you can choose an appropriate script. If a script cannot run on the RAID system, it displays an error message. This action requires Super User or Power User privileges. To use the Optimal Configurations Wizard: 1. Click the Storage tab. 2. Click the Wizard icon. 3. Click the Optimal Configurations button. 4. Click the option button next to the script you want to use. 5.
Chapter 4: Management with WebPAM PROe 4. To accept the proposed configuration, click the Submit button. 5. Click the Finish button to clear the Automatic Configuration box. Note If you disagree with the proposed configuration, click the Cancel button, then click the Express button or the Advanced button and input your parameters manually. Wizard: Express Configuration When you choose the Express option, a set of characteristics and options appears on the screen.
VTrak E-Class Product Manual 7. Click the Next button to continue. The Summary screen appears with information on disk arrays, logical drives, and spare drives you are about to create. 8. To accept the proposed configuration, click the Submit button. 9. Click the Finish button to clear the Express Configuration box. Note If you disagree with the proposed configuration, review and modify your selections in the previous steps.
Chapter 4: Management with WebPAM PROe Look for drives with a green LED dark, a blue LED lit, and no crosshatching over the carrier. Green LED dark Blue LED lit 3. Click a physical drive to select it for your array. The physical drive’s ID number is added to the Selected list. 4. Click the Next button to continue. The Create Logical Drive screen displays. Task 2 – Logical Drive Creation To create your logical drive: 1. Enter your information and choose your options.
VTrak E-Class Product Manual Task 3 – Spare Drive Creation To create your spare drive: 1. For each of the following items, accept the default or change the settings as required: • Check the Revertible box if you want a revertible spare drive. A revertible spare drive returns to its spare drive assignment after you replace the failed physical drive in the disk array and run the Transition function. 2.
Chapter 4: Management with WebPAM PROe Making Disk Array Settings To make disk array settings: 1. 2. Click the Storage tab. Click the Disk Array icon. The list of disk arrays appears. 3. Click the disk array you want, then click the Settings button. 4. Make settings changes as required: • Enter, change or delete the alias in the Alias field Maximum of 32 characters; letters, numbers, space between characters, and underline. 5. • Media Patrol – Check to enable, uncheck to disable on this array.
VTrak E-Class Product Manual Notes • You can also enable or disable Media Patrol for the entire RAID system. See “Making Media Patrol Settings” on page 118. • HDD Power Saving must be enabled on the RAID controller for the Power Management settings to be effective. See “Making Controller Settings” on page 86. • Power Management functions are limited to the features your HDDs actually support.
Chapter 4: Management with WebPAM PROe 2. Click the Background Activities icon. The list of background activities appears. 3. Mouse-over Media Patrol and click the Start button. Stopping, Pausing or Resuming Media Patrol To stop, pause or resume Media Patrol: 1. 2. Click the Administration tab. Click the Background Activities icon. The list of background appears. 3. Mouse-over Media Patrol and click the Stop, Pause or Resume button.
VTrak E-Class Product Manual Preparing a Disk Array for Transport This feature prepares the physical drives that make up the disk array to be removed from the enclosure and installed in a different location. To prepare a disk array for transport: 1. 2. Click the Storage tab. Click the Disk Array icon. The list of disk arrays appears. 3. Click the disk array you want, then click the Transport button. 4. Click the Confirm button. The status changes to Transport Ready. 5.
Chapter 4: Management with WebPAM PROe 5. From the Target Physical Drive dropdown menu, choose a Target physical drive. 6. Click the Confirm button. When the disk array is rebuilding: • The disk array shows a green check icon and Rebuilding status. • Logical drives under the disk array continue to show a yellow ! and Critical status. Stopping, Pausing or Resuming a Rebuild To stop, pause or resume a Rebuild: 1. Click the Administration tab. 2. Click the Background Activities icon.
VTrak E-Class Product Manual Managing Logical Drives Logical drive management includes: • Viewing a List of Logical Drives (below) • Viewing Logical Drive Information (page 163) • Viewing Logical Drive Statistics (page 164) • Viewing Logical Drive Check Tables (page 164) • Creating a Logical Drive Manually (page 165) • Deleting a Logical Drive (page 166) • Making Logical Drive Settings (page 166) • Locating a Logical Drive (page 167) • Locating a Logical Drive (page 167) • Initializing a
Chapter 4: Management with WebPAM PROe Viewing Logical Drive Information To view logical drive information: 1. 2. Click the Storage tab. Click the Logical Drive icon. The list of logical drives appears. 3. Click the logical drive you want, then click the View button. Logical Drive information displays, including: • ID – LD0, LD1, LD2, etc.
VTrak E-Class Product Manual Viewing Logical Drive Statistics To view logical drive statistics: 1. 2. Click the Storage tab. Click the Logical Drive icon. The list of logical drives appears. 3. Click the logical drive you want, then click the View button. 4. Click the Statistics tab.
Chapter 4: Management with WebPAM PROe • Inconsistent Block – Inconsistent blocks for this logical drive. Mirror data for RAID Levels 1, 1E and 10 or Parity data for RAID Levels 5, 6, 50, and 60. Identified by the Redundancy Check. The Check Table lists: • Entry Number – A number assigned to each block of entry. • Table Type – Read Check, Write Check or Inconsistent Block. • Start Logical Block Address – LBA of the first block for this entry.
VTrak E-Class Product Manual • Choose a Read (cache) Policy. • Choose a Write (cache) Policy. Read Cache, Read Ahead, and No Cache are available. Write Back and Write Through (Thru) are available. 10. Click the Add button. The new logical drive appears on the list at the right. If there is capacity remaining, you can create an additional logical drive. 11. When you are finished, click the Submit button. The new logical drive or drives appear in the logical drive list.
Chapter 4: Management with WebPAM PROe • Choose a Read (cache) Policy. • Choose a Write (cache) Policy. Read Cache, Read Ahead, and No Cache are available. Write Back and Write Through (Thru) are available. 5. Click the Save button. For more information, see “Cache Policy” on page 362. Note The Write Cache is always set to WriteThru when Read Cache is set to NoCache.
VTrak E-Class Product Manual To initialize a logical drive: 1. Click the Administration tab. 2. Click the Background Activities icon. The list of background activities appears. 3. Mouse-over Initialization and click the Start button. 4. Check the box to the left of the logical drive you want to initialize. 5. Choose the initialization option you want: 6. • Quick Initialization – Check the box and enter a value in the Quick Initialization Size field.
Chapter 4: Management with WebPAM PROe Stopping, Pausing or Resuming a Redundancy Check To stop, pause or resume Redundancy Check: 1. Click the Administration tab. 2. Click the Background Activities icon. The list of background activities appears. 3. Mouse-over Redundancy Check and click the Stop, Pause, or Resume button. Migrating a Logical Drive’s RAID Level The term “Migration” means either or both of the following: • Change the RAID level of a logical drive.
VTrak E-Class Product Manual 9. In the Capacity field, accept the current capacity. Or check the Expand Capacity box and enter a greater capacity and size in MB, GB or TB. If there is capacity remaining, you can create an additional logical drive. 10. Click the Next button. The logical drive ID numbers, with the original and target RAID levels and capacities are shown 11. To accept the proposed target values, click the Confirm button.
Chapter 4: Management with WebPAM PROe • From the Choose a RAID level dropdown menu, choose the RAID level of the LUN clone. • From the Number of Copies dropdown menu, choose the number of LUN clones you want to create. • Check the box to the left of the Disk Array on which you want to create the LUN clone. You can make up to 8 clones of a LUN at a time. 5. Click the Next button and review your choices. 6. Click the Start button to begin the cloning process. The cloning progress bar displays.
VTrak E-Class Product Manual Managing Spare Drives Spare drive management includes: • Viewing a List of Spare Drives (below) • Viewing Spare Drive Information (page 172) • Creating a Spare Drive Manually (page 173) • Creating a Spare Drive with the Wizard, see “Creating a Disk Array with the Wizard” on page 151 • Deleting a Spare Drive (page 174) • Making Spare Drive Settings (page 174) • Locating a Spare Drive (page 174) • Running Spare Check (page 175) • Running a Transition on a Spare D
Chapter 4: Management with WebPAM PROe • Physical Drive ID – ID number of the physical drive chosen for this spare • Operational Status – OK means normal • Spare Type – Global or Dedicated • Physical Capacity – Total data capacity of the spare drive • Revertible – Yes or No • Configurable Capacity – Usable capacity of the spare drive • Spare Check Status – Not Checked or Healthy • Media Patrol – Enabled or Not Enabled • Dedicated to Array – ID number of the disk array to which the spare is
VTrak E-Class Product Manual Deleting a Spare Drive This action requires Administrator or a Super User privileges. To delete a spare drive: 1. Click the Storage tab. 2. Click the Spare Drive icon. 3. Click the spare drive you want, then click the Delete button. 4. In the Confirmation box, type the word “confirm” in the field provided and click the Confirm button. Making Spare Drive Settings For more information on settings options, see “Spare Drives” on page 355. To make spare drive settings: 1.
Chapter 4: Management with WebPAM PROe 6. Click the physical drive with the matching ID number and click the Locate button. The drive carrier LED blinks for one minute. Green LEDs flash Running Spare Check Spare Check verifies the status of your spare drives. To run spare check: 1. Click the Storage tab. 2. Click the Spare Drive icon. The list of spare drives appears. 3. 4. Click the spare drive you want, then click the Spare Check button. Click the Confirm button.
VTrak E-Class Product Manual 5. From the Target Physical Drive dropdown menu, choose a Target unconfigured drive. 6. Click the Confirm button. Stopping, Pausing or Resuming a Transition To stop, pause or resume Transition: 1. 2. Click the Administration tab. Click the Background Activities icon. The list of background activities appears. 3. Mouse-over Transition and click the Stop, Pause, or Resume button.
Chapter 4: Management with WebPAM PROe Managing Initiators Initiator management includes: • Viewing a List of Initiators (below) • Adding an FC Initiator (page 177) • Deleting an FC Initiator (page 178) • Adding an iSCSI Initiator (page 178) Viewing a List of Initiators The VTrak’s initiator list displays initiators available for mapping to a LUN or logical drive. You must add initiators to the VTrak’s initiator list to make them available for mapping to a LUN. To view a list of initiators: 1.
VTrak E-Class Product Manual 5. Click the Submit button. The initiator is added. Method 2: Adding from a List This action requires Administrator or Super User privileges. To add a Fibre Channel initiator to the list: 1. Click the Device tab. 2. Click the Fibre Channel Management icon. 3. Click the Logged In Device tab. 4. Check the box next to the initiator you want to add. 5. Click the Add to Initiator List button. The initiator is added, and its check box grays out.
Chapter 4: Management with WebPAM PROe Example: iqn.1991-05.com.microsoft:promise-29353b7. Obtain the initiator name from the initiator utility on your host system. Note that the initiator name you input must match exactly in order for the connection to work. 5. Click the Submit button. The initiator is added to the list.
VTrak E-Class Product Manual Managing LUNs LUN management includes: • Viewing a List of LUN Maps (below) • LUN Mapping and Masking (page 180) • Adding a LUN Map (page 180) • Editing a LUN Map (page 182) • Deleting a LUN Map (page 182) • Changing the Active LUN Map Type (page 182) • Enabling and Disabling LUN Masking (page 183) Viewing a List of LUN Maps To view a list of LUN maps: 1. Click the Storage tab. 2. Click the LUN Mapping & Masking icon. The list of LUN maps appears.
Chapter 4: Management with WebPAM PROe A maximum of 1024 logical drives can be mapped to an FC initiator or port, or to an iSCSI initiator or target. To assign a LUN to an initiator, add the initiator first. See “Adding an FC Initiator” on page 177 or “Adding an iSCSI Initiator” on page 178. LUN masking must be enabled in order to map a LUN. See “Enabling and Disabling LUN Masking” on page 183. To add a LUN map: 1. Click the Storage tab. 2. Click the LUN Mapping & Masking icon. 3.
VTrak E-Class Product Manual Editing a LUN Map Editing a LUN map is the action of assigning a logical drive or LUN to an initiator. By changing the assignment, you change the initiator’s access. To edit a LUN map: 1. 2. Click the Storage tab. Click the LUN Mapping & Masking icon. The list of LUN maps appears. 3. Click the LUN map you want, then click the Setting button. 4. Beside Active LUN Mapping Type, • FC subsystems, choose the Initiator or Port option.
Chapter 4: Management with WebPAM PROe To change the active LUN mapping type: 1. Click the Storage tab. 2. Click the LUN Mapping & Masking icon. The list of LUN maps appears. 3. Beside Active LUN Mapping Type: • FC subsystems, choose the Initiator or Port option. • iSCSI subsystems, choose the Initiator or Target option. When you change the LUN map type, a popup message appears. 4. In the popup message type “confirm” and click the Confirm button.
VTrak E-Class Product Manual Managing Fibre Channel Connections Fibre Channel management includes: • Viewing FC Node Information (below) • Viewing FC Port Information (page 184) • Making FC Port Settings (page 185) • Viewing FC Port Statistics (page 186) • Viewing a List of FC Initiators on the Fabric (page 186) • Viewing a List of FC Logged-in Devices (page 186) • Viewing a List of FC SFPs (page 186) Also see “Adding an FC Initiator” on page 177 and “Deleting an FC Initiator” on page 178.
Chapter 4: Management with WebPAM PROe • Worldwide Port Number (WWPN) Making FC Port Settings To make Fibre Channel port settings: 1. Click the Device tab. 2. Click the FC Management icon. 3. Click the Port tab. 4. Click the FC port you want to access and click the Settings button. 5. Make these changes as required: • Choose a configured link speed from the dropdown menu. The choices are Auto (default), 2 Gb/s, 4 Gb/s, and 8 Gb/s. • Choose a topology from the dropdown menu.
VTrak E-Class Product Manual Viewing FC Port Statistics To view Fibre Channel port statistics: 1. Click the Device tab. 2. Click the FC Management icon. 3. Click the Statistics tab. 4. Mouse over the FC port you want to access and click the View button. To clear FC port statistics, see “Clearing Statistics” on page 79. Viewing a List of FC Initiators on the Fabric To view a list Fibre Channel initiators on the fabric: 1. Click the Device tab. 2. Click the FC Management icon. 3.
Chapter 4: Management with WebPAM PROe SFP information includes: • FC port ID • Controller ID • Connector type • Transceiver type • Transceiver code • Vendor name 187
VTrak E-Class Product Manual Managing iSCSI Connections iSCSI management includes: • Making Global iSCSI Settings (page 189) • Viewing a List of iSCSI Targets (page 189) • Viewing iSCSI Target Information (page 189) • Adding iSCSI Targets (page 190) • Making iSCSI Target Settings (page 191) • Deleting an iSCSI Target (page 191) • Assigning a Portal to an iSCSI Target (page 192) • Un-assigning a Portal from an iSCSI Target (page 192) • Viewing a List of iSCSI Portals (page 192) • Viewing iSCSI Portal Inform
Chapter 4: Management with WebPAM PROe A detailed explanation of iSCSI functions and how to best use them is beyond the scope of this document. For more information, contact the Internet Engineering Task Force at http://www.ietf.org/. Making Global iSCSI Settings This setting enables and disables the Keep Alive feature on all iSCSI sessions. You can also enable and disable Keep Alive on individual sessions. See page 200. To make global iSCSI settings: 1. Click the Device tab. 2.
VTrak E-Class Product Manual • Name – iSCSI qualified name (iqn) of this target. • Alias – Maximum of 32 characters. Use letters, numbers, space between words, and underscore. An alias is optional.* • Status – Up or down. • Error Recovery Level – Error recovery level supported. • Initial R2T – Allows initiator to begin sending data to a target without receiving a ready to transfer command.
Chapter 4: Management with WebPAM PROe Header and data digests work best with initiators equipped with a TCP Offload Engine (TOE). For more information, see your iSCSI HBA user documentation. VTrak supports a maximum 2048 iSCSI targets. A maximum of 1024 logical drives can be mapped to a target. To add a target: 1. Click the Device tab. 2. Click the iSCSI Management icon. 3. Click the Target tab. 4. Click the Create Target button. 5. Optional. In the Alias field, type an alias for this target. 6.
VTrak E-Class Product Manual 2. Click the iSCSI Management icon. 3. Click the Target tab. 4. Click the target you want, then click the Delete button. 5. In the Confirmation box, type the word “confirm” in the field provided and click the Confirm button. The target is removed from the list. Assigning a Portal to an iSCSI Target Before you can assign a portal to a target, you must create the portal. See “Adding iSCSI Portals” on page 194. To assign a portal to an iSCSI target: 1.
Chapter 4: Management with WebPAM PROe 3. Click the Portal tab. Portal information includes: • ID – Portal number. Starts at 0. • IP Address – IP address of the portal. • Controller ID – RAID controller ID, 1 or 2. • Port ID – Physical port on the RAID controller, 1 to 4. • Trunk ID – Trunk ID, 1 to 8. Refers to portals associated with a trunk (link aggregation). N/A means this portal is not assciated with a trunk. • VLAN Tag – VLAN Tag, 0 to 4094.
VTrak E-Class Product Manual Items marked with an asterisk (*) are adjustable under “Making iSCSI Portal Settings” on page 194. Adding iSCSI Portals VTrak supports up to 32 iSCSI portals per iSCSI port. Each iSCSI portal can belong to a different VLAN for a maximum of 32 VLANs. If you plan to associate the new portal with a trunk, create the trunk first. See “Adding iSCSI Trunks” on page 197. For more information about iSCSI VLANs, see “iSCSI on a VLAN” on page 368. To add a portal: 1.
Chapter 4: Management with WebPAM PROe 2. Click the iSCSI Management icon. 3. Click the Portal tab. 4. Click the portal you want, then click the Settings button. 5. Make settings changes as needed: • If you have a Trunk association, choose a Trunk ID (1 to 8) from the dropdown menu. • Type the IP address of the portal in the field provided. • Type the subnet mask of the portal in the field provided. • If you have a VLAN association, enter a VLAN tag (0 to 4094) in the field provided.
VTrak E-Class Product Manual • Jumbo Frames – Enabled or disabled* • Current Speed – In Mb/s • Assigned Portals – Portals to which this port is assigned Items marked with an asterisk (*) are adjustable under “Making iSCSI Port Settings” on page 196 Viewing iSCSI Port Information To view information about a port: 1. Click the Device tab. 2. Click the iSCSI Management icon. 3. Click the Port tab. 4. Click the port you want, then click the View button.
Chapter 4: Management with WebPAM PROe Viewing a List of iSCSI Trunks A trunk is the aggregation of two or more iSCSI ports to increase bandwidth. To view a list of trunks: 1. Click the Device tab. 2. Click the iSCSI Management icon. 3. Click the Trunk tab.
VTrak E-Class Product Manual Making iSCSI Trunk Settings To make trunk settings: 1. Click the Device tab. 2. Click the iSCSI Management icon. 3. Click the Trunk tab. 4. Click the trunk you want, then click the Settings button. 5. Make changes as required: 6. • Controller ID – ID of the RAID controller, 1 or 2 • Master Port number – ID of the master port • Slave Port number – IDs the slave ports Click the Submit button.
Chapter 4: Management with WebPAM PROe Viewing iSCSI Session Information To view a list of iSCSI sessions: 1. Click the Device tab. 2. Click the iSCSI Management icon. 3. Click the Session tab. 4. Click the iSCSI session you want and click the View button.
VTrak E-Class Product Manual Making iSCSI Session Settings To make iSCSI session settings: 1. Click the Device tab. 2. Click the iSCSI Management icon. 3. Click the Session tab. 4. Click the iSCSI session you want and click the Settings button. 5. Check the box to enable the Keep Alive feature. Uncheck the box to disable. 6. Click the Submit button. You can also enable and disable the Keep Alive as a global setting. See page 189. Deleting an iSCSI Session To delete an iSCSI session: 1.
Chapter 4: Management with WebPAM PROe Making iSCSI iSNS Settings To make iSNS settings: 1. Click the Device tab. 2. Click the iSCSI Management icon. 3. Click the iSNS tab. 4. Click the iSNS Settings button. 5. Make settings changes are required: 6. • Check the box to enable iSNS. Uncheck to disable. • Enter the iSNS server IP address. • Enter a new iSNS Port number. The range is 1 to 65535. Click the Submit button. Viewing a List of iSCSI CHAPs To view a list of iSCSI CHAPs: 1.
VTrak E-Class Product Manual 6. • Peer is one-way or uni-directional. • Local is two-way or bi-directional. • Enter a secret of 12 to 99 characters in the Secret field. • Enter the secret again in the Retype Secret field. Click the Submit button. The new CHAP is added to the list. Making iSCSI CHAP Settings When you change CHAP settings, you must change the secret. You cannot change the type (peer or local). To make iSCSI CHAP settings: 1. Click the Device tab. 2.
Chapter 4: Management with WebPAM PROe To ping a host or server on the network: 1. Click the Device tab. 2. Click the iSCSI Management icon. 3. Click the Ping tab. 4. Type the IP address of the host or server into the IP Address field. 5. Choose the port Type from the dropdown menu. • iSCSI means an iSCSI port • Mgmt means the VTrak’s virtual management port 6. If you chose iSCSI port, choose the RAID controller and port number from the dropdown menus. 7.
VTrak E-Class Product Manual 204
Chapter 5: Management with the CLU This chapter covers the following topics: • Initial Connection (page 206) • Managing the Subsystem (page 211) • Managing the RAID Controllers (page 215) • Managing the Enclosure (page 219) • Managing Physical Drives (page 225) • Managing Disk Arrays (page 229) • Managing Spare Drives (page 239) • Managing Logical Drives (page 242) • Managing the Network Connection (page 250) • Managing Fibre Channel Connections (page 252) • Managing iSCSI Connections (
VTrak E-Class Product Manual Initial Connection Making an initial connection includes the following functions: • Making a Serial Connection (page 206) • Making a Telnet Connection (page 207) • Making a SSH Connection (page 207) • Logging Into the CLI (page 208) • Accessing Online Help (page 209) • Exiting the CLU (page 210) • Logging Out of the CLI (page 210) • Logging Back Into the CLI and CLU (page 210) Making a Serial Connection Before you begin, be sure the RJ11-to-DB9 serial data cable
Chapter 5: Management with the CLU 3. Press Enter once to launch the CLI. Making a Telnet Connection A Telnet connection requires a network connection between the Host PC and the Management (Ethernet) port on the VTrak controller. Figure 2. Management port on the RAID controller Management port To start the telnet program: 1. Go to the command line prompt (Windows) or click the terminal icon (Linux). 2. Type telnet 192.168.1.56 2300 and press Enter. The IP address above is only an example.
VTrak E-Class Product Manual 3. Press Enter once to launch the CLI. Linux To start the Linux SSH program: 1. Click the terminal icon. 2. Type ssh 192.168.1.56 22 and press Enter. The IP address above is only an example. Use the Management port IP address of your VTrak. The SSH default port number is 22. 3. Press Enter once to launch the CLI. Logging Into the CLI 1. At the Login prompt, type the user name and press Enter. The default user name is administrator. 2.
Chapter 5: Management with the CLU Quick Setup – A sequence of four steps to setup system date and time, Management port, and RAID configuration. See “Setting-up VTrak with the CLU” on page 55. Subsystem Management – Subsystem settings, Controller settings, statistics, lock/unlock the subsystem, set date and time, Enclosure settings, FRUs and Topology.
VTrak E-Class Product Manual Exiting the CLU 1. Highlight Return to Previous Menu and press Enter. Repeat this action until you arrive at the Main Menu. 2. From the Main Menu, highlight Return to CLI and press Enter to exit 3. Close the terminal emulation, Telnet, SSH, or terminal window. Logging Out of the CLI When you shut down or restart the VTrak subsystem, you are automatically logged out of the CLI.
Chapter 5: Management with the CLU Managing the Subsystem Subsystem Management includes the following functions: • Making Subsystem Settings (page 211) • Running Media Patrol (page 211) • Locking or Unlocking the Subsystem (page 212) • Setting Subsystem Date and Time (page 212) • Making NTP Settings (page 213) • Synchronizing with a NTP Server (page 214) Making Subsystem Settings An alias is optional. To set an Alias for this subsystem: 1.
VTrak E-Class Product Manual Locking or Unlocking the Subsystem The lock prevents other sessions (including sessions with the same user) from making a configuration change to the controller until the lock expires or a forced unlock is done. When the user who locked the controller logs out, the lock is automatically released. Setting the Lock To set the lock: 1. From the Main Menu, highlight Subsystem Management and press Enter. 2. Highlight Lock Management and press Enter. 3.
Chapter 5: Management with the CLU 3. Highlight the System Date or System Time setting. 4. Press the backspace key to erase the current value. 5. Type in a new value. 6. Press Control-A to save your settings. Making NTP Settings After you have made Network Time Protocol (NTP) settings, the VTrak subsystem synchronizes with a NTP server. • At startup • Every night • When you synchronize manually To make NTP settings for the subsystem: 1.
VTrak E-Class Product Manual Synchronizing with a NTP Server The VTrak subsystem automatically synchronizes with a NTP server every night and a startup. You have the option of synchronizing manually at any time. To manually synchronize the VTrak with a NTP server: 1. From the Main Menu, highlight Subsystem Management and press Enter. 2. Highlight NTP Management and press Enter. 3. Highlight Start Time Sync and press Enter. 4. Press Y to confirm.
Chapter 5: Management with the CLU Managing the RAID Controllers RAID controller management includes the following functions: • Viewing Controller Information (page 215) • Clearing an Orphan Watermark (page 215) • Making Controller Settings (page 216) • Locating the Controller (page 217) Viewing Controller Information Controller Management includes information, settings and statistics. To access Controller Management: 1. 2. From the Main Menu, highlight Subsystem Management and press Enter.
VTrak E-Class Product Manual The condition is cleared. See “Physical Drive Problems” on page 399 for more information. Making Controller Settings If your subsystem has two controllers, any settings you make to one controller automatically apply to the other controller. To make Controller settings: 1. From the Main Menu, highlight Subsystem Management and press Enter. 2. Highlight Controller Management and press Enter. 3. Highlight the controller you want and press Enter. 4.
Chapter 5: Management with the CLU • Highlight SMART Poll Interval and press the backspace key to erase the current value. Type a new interval value (1 to 1440 minutes). • Highlight Poll Interval and press the backspace key to erase the current value. Type a new interval value (15 to 255 seconds). • Highlight Adaptive Writeback Cache and press the spacebar to toggle between Enabled and Disabled. For more information, see “Adaptive Writeback Cache” on page 363.
VTrak E-Class Product Manual Figure 4.
Chapter 5: Management with the CLU Managing the Enclosure Enclosure Management includes the following functions: • Viewing the Enclosures Summary (page 219) • Viewing Enclosure Information (page 219) • Making Enclosure Settings (page 220) • Viewing FRU VPD Information (page 220) • Viewing Power Supply Status (page 220) • Locating a Power Supply (page 221) • Viewing Cooling Unit Status (page 221) • Viewing Temperature Sensor Status (page 221) • Viewing Voltage Sensor Status (page 222) • V
VTrak E-Class Product Manual Adjustable items You can set or adjust the following items: • Enclosure Warning and Critical temperature thresholds • Controller Warning and Critical temperature thresholds See “Making Enclosure Settings” below. For information on Enclosure problems, see “Enclosure Problems” on page 391. Making Enclosure Settings To make Enclosure settings: 1. From the Main Menu, highlight Subsystem Management and press Enter. 2. Highlight Enclosure Management and press Enter. 3.
Chapter 5: Management with the CLU 3. Highlight the enclosure you want and press Enter. 4. Highlight Power Supplies and press Enter. The screen displays the operational and fan status of VTrak’s two power supplies. If any status differs from normal or the fan speed is below the Healthy Threshold value, there is a fan/power supply malfunction. See “Replacing a Power Supply” on page 323. Locating a Power Supply To locate a power supply: 1.
VTrak E-Class Product Manual Viewing Voltage Sensor Status To view the status of the voltage sensors: 1. From the Main Menu, highlight Subsystem Management and press Enter. 2. Highlight Enclosure Management and press Enter. 3. Highlight the enclosure you want and press Enter. 4. Highlight Voltage Sensors and press Enter. If any voltage is outside the Healthy Threshold values, there is a voltage malfunction in the enclosure. See “Diagnosing an Enclosure Problem” on page 391.
Chapter 5: Management with the CLU Reconditioning a Battery To recondition the subsystem battery: 1. From the Main Menu, highlight Subsystem Management and press Enter. 2. Highlight Enclosure Management and press Enter. 3. Highlight the enclosure you want and press Enter. 4. Highlight Batteries and press Enter. 5. Highlight the battery you want to recondition and press Enter. 6. Highlight Start Reconditioning and press Enter. 7. Press Y to confirm.
VTrak E-Class Product Manual For more information about connections, see “Making Management and Data Connections” on page 25. To view enclosure topology: 1. From the Main Menu, highlight Subsystem Management and press Enter. 2. Highlight Enclosure Topology and press Enter. The following information applies to the Head Unit: • Enclosure number – 1 • Controller number – 1 or 2 • Port number • Status – OK is normal.
Chapter 5: Management with the CLU Managing Physical Drives Physical Drive Management includes the following functions: • Viewing a List of Physical Drives (page 225) • Making Global Physical Drive Settings (page 225) • Viewing Physical Drive Information (page 226) • Viewing Physical Drive Statistics (page 226) • Setting an Alias (page 227) • Clearing Stale and PFA Conditions (page 227) • Forcing a Physical Drive Offline (page 227) • Locating a Physical Drive (page 228) Viewing a List of Ph
VTrak E-Class Product Manual For SAS drives: • Highlight Write Cache and press the spacebar to toggle between Enabled and Disabled. • Highlight Read Look Ahead Cache and press the spacebar to toggle between Enabled and Disabled. • Highlight CmdQueuing and press the spacebar to toggle between Enabled and Disabled. • Highlight MediumErrorThreshold and press the backspace key to remove the current value, then type a new smaller value.
Chapter 5: Management with the CLU Setting an Alias An alias is optional. To set an Alias for a physical drive: 1. From the Main Menu, highlight Physical Drive Management and press Enter. 2. Highlight the physical drive you want and press Enter. 3. Type an alias into the field provided. Maximum of 32 characters. Use letters, numbers, space between words and underscore. 4. Press Control-A to save your settings.
VTrak E-Class Product Manual Important Forcing a physical drive offline causes your logical drives to become degraded. If Auto Rebuild is enabled and a spare drive is available, the disk array begins rebuilding itself automatically. To force a physical drive offline: 1. From the Main Menu, highlight Physical Drive Management and press Enter. 2. Highlight Global Physical Drives Settings and press Enter. 3. Highlight the physical drive you want and press Enter. 4.
Chapter 5: Management with the CLU Managing Disk Arrays Disk Array Management includes the following functions: • Viewing a List of Disk Arrays (page 229) • Creating a Disk Array (page 229) • Deleting a Disk Array (page 233) • Making Disk Array Settings (page 233) • Viewing Disk Array Information (page 234) • Enabling Media Patrol, PDM, and Power Management on a Disk Array (page 235) • Preparing the Disk Array for Transport (page 236) • Rebuilding a Disk Array (page 236) • Running PDM on a
VTrak E-Class Product Manual Creating a Disk Array – Automatic To create a disk array using the Automatic feature: 1. From the Main Menu, highlight Disk Array Management and press Enter. 2. Highlight Create New Array and press Enter. 3. Highlight Configuration Method and press the spacebar to toggle to Automatic. 4. Press Control-A to save your settings and move to the next screen. 5. Review the proposed configuration of disk array and logical drives.
Chapter 5: Management with the CLU Creating a Disk Array – Express To create a disk array using the Express feature: 1. From the Main Menu, highlight Disk Array Management and press Enter. 2. Highlight Create New Array and press Enter. 3. Highlight Configuration Method and press the spacebar to toggle to Express. 4.
VTrak E-Class Product Manual Creating a Disk Array – Advanced For more information on the choices below, see “Chapter 7: Technology Background” on page 331. To create a disk array using the Advanced feature: 1. From the Main Menu, highlight Disk Array Management and press Enter. 2. Highlight Create New Array and press Enter. 3. Highlight Configuration Method and press the spacebar to toggle to Advanced. Step 1 – Disk Array Creation 1.
Chapter 5: Management with the CLU 6. • Highlight Sector and press the spacebar to toggle through sector sizes and choose 512 B, 1 KB, 2 KB, or 4 KB. • Highlight Write Policy and press the spacebar to toggle write cache policy between WriteBack and WriteThru (write though). • Highlight Read Policy and press the spacebar to toggle read cache policy though ReadCache, ReadAhead, and NoCache. • Highlight Preferred Controller ID and press the spacebar to toggle among 1, 2, or Automatic.
VTrak E-Class Product Manual The list of disk arrays appears. 2. Highlight the disk array you want and press the Enter. 3. Make settings changes as required: • Enter, change or delete the alias in the Alias field Maximum of 32 characters; letters, numbers, space between characters, and underline. 4. • Media Patrol – Highlight and press the spacebar to toggle between enable and disable. • PDM – Highlight and press the spacebar to toggle between enable and disable.
Chapter 5: Management with the CLU • Synchronizing – This condition is temporary. Synchronizing is a maintenance function that verifies the integrity of data and redundancy in the logical drive. When a logical drive is Synchronizing, it functions and your data is available. However, access is slower due to the synchronizing operation. • Critical/Degraded – This condition arises as the result of a physical drive failure. A degraded logical drive still functions and your data is still available.
VTrak E-Class Product Manual 3. Highlight Media Patrol and press the spacebar to toggle between Enable and Disable. 4. Highlight PDM and press the spacebar to toggle between Enable and Disable. 5. Highlight Power Management and press the spacebar to toggle between Enable and Disable. 6. Press Control-A to save your settings. See “Running PDM on a Disk Array” on page 237 and “Making Background Activity Settings” on page 273.
Chapter 5: Management with the CLU See “Enabling Media Patrol, PDM, and Power Management on a Disk Array” on page 235. For Media Patrol rate, see “Making Background Activity Settings” on page 273. For more information, see page 331. Running PDM on a Disk Array Predictive Data Migration (PDM) migrates data from the suspect physical drive to a spare drive before the physical drive fails. Before you can run PDM, you must have a replacement or target physical drive of adequate capacity for your disk array.
VTrak E-Class Product Manual Default source and target drives are shown with possible alternative choices. 5. To choose different drive, highlight the drive, press the backspace key to remove the current number, then type a new number. 6. Highlight Start and press Enter. For transition rate, see “Making Background Activity Settings” on page 273. Locating a Disk Array This feature helps you identify the physical drives assigned to the disk array you are working with in the CLU.
Chapter 5: Management with the CLU Managing Spare Drives Spare Drive Management includes the following functions: • Viewing a list of Spare Drives (page 239) • Creating a Spare Drive (page 239) • Making Spare Drive Settings (page 240) • Running Spare Check (page 240) • Deleting a Spare Drive (page 241) Viewing a list of Spare Drives To view a list of spare drives: From the Main Menu, highlight Spare Drive Management and press Enter.
VTrak E-Class Product Manual 5. Highlight Spare Type and press the spacebar to toggle between Dedicated and Global. Dedicated means this spare drive can only be used with the specified disk arrays. Global means this spare drive can be used by any disk array. If you chose Dedicated, a default disk array is shown with possible alternative choices. To choose different array, highlight the array and press the backspace key to erase the current number, then type the new number. 6.
Chapter 5: Management with the CLU Deleting a Spare Drive Caution If the spare drive you delete is the only spare, the controller does not rebuild a critical array until you provide a new spare drive. To delete a spare drive: 1. From the Main Menu, highlight Spare Drive Management and press Enter. A list of the current spare drives appears. 2. Highlight the spare drive you want to delete and press the spacebar to mark it. The mark is an asterisk (*) to the left of the listing. 3.
VTrak E-Class Product Manual Managing Logical Drives Logical drive management includes: • Creating a Logical Drive (page 242) • Deleting a Logical Drive (page 243) • Viewing Logical Drive Information (page 243) • Viewing Logical Drive Statistics (page 244) • Viewing the Logical Drive Check Table (page 244) • Making Logical Drive Settings (page 245) • Initializing a Logical Drive (page 245) • Running Redundancy Check (page 246) • Locating a Logical Drive (page 246) • Migrating a Logical D
Chapter 5: Management with the CLU • Stripe size – Press the spacebar to choose: 64 KB, 128 KB, 256 KB, 512 KB, or 1 MB. • Sector size – Press the spacebar to choose: 512 B; 1 KB, 2 KB, or 4 KB. • Write Policy – Press spacebar to choose: Write Back or Write Through. • Read Policy – Press spacebar to choose: No Cache, Read Cache, or Read Ahead Cache. 7. Highlight Preferred Controller ID and press the spacebar to toggle among 1, 2, or Automatic.
VTrak E-Class Product Manual To view logical drive information: 1. From the Main Menu, highlight Logical Drive Management and press Enter. 2. Highlight the logical drive you want and press Enter. The information and settings screen appears. 3. Highlight any of the following and press Enter to view more information: • Check Table – Read Check, Write Check, and Inconsistency Check Tables • Logical Drive Statistics Viewing Logical Drive Statistics To view logical drive information: 1. 2.
Chapter 5: Management with the CLU Making Logical Drive Settings To make Logical Drive settings: 1. From the Main Menu, highlight Logical Drive Management and press Enter. 2. Highlight the logical drive you want and press Enter. 3. For the following items, accept the existing setting choose a new one: • Highlight Alias and type an alias into the field provided. Maximum of 32 characters. Use letters, numbers, space between words and underscore. An alias is optional. 4.
VTrak E-Class Product Manual To change a parameter, highlight it and press the backspace key to erase the current value, then type the new value. 5. Highlight Start and press Enter. If necessary, you can pause and resume or stop and restart the Initialization. You cannot access the logical drive until Initialization has finished. For initialization rate, see “Making Background Activity Settings” on page 273.
Chapter 5: Management with the CLU Figure 7. Drive carrier status LED Green LED flashes Migrating a Logical Drive In order to migrate RAID level, you may have to add physical drives. For more information, see “RAID Level Migration” on page 347. To migrate a logical drive: 1. From the Main Menu, highlight Disk Array Management and press Enter. 2. Highlight the disk array you want and press Enter. 3. Highlight Background Activities and press Enter. 4. Highlight Migration and press Enter. 5.
VTrak E-Class Product Manual 12. Press Y to confirm. The screen returns to Disk Arrays Summary. For migration rate, see “Making Background Activity Settings” on page 273. Creating a LUN Clone A LUN clone is an exact copy of the original LUN or logical drive, including all the data it contains, at one point in time. Use a LUN clone as a backup or to migrate a LUN from one system to another.
Chapter 5: Management with the CLU If you chose a redundant RAID level, the LUN clone is automatically synchronized after creation. After the LUN clone is created, you can manage it like any other logical drive. See “Making Spare Drive Settings” on page 240, “Locating a Logical Drive” on page 246, and “Deleting a Logical Drive” on page 243. For users to access the LUN clone, you must map it to an initiator. See “Working with LUN Mapping” on page 277.
VTrak E-Class Product Manual Managing the Network Connection Network Management deals with network connections and settings for the VTrak’s Management ports. Each Management Port can be configured: • Making Virtual Management Port Settings (page 250) • Making Maintenance Mode Settings (page 251) Making Virtual Management Port Settings The VTrak subsystem has a virtual management port, enabling you to log into a VTrak with dual controllers using one IP address.
Chapter 5: Management with the CLU 6. • Subnet Mask • Default Gateway IP Address • DNS Server IP Address Press Control-A to save your settings. Making Maintenance Mode Settings Each controller has its own IP addresses for access when the controller goes into maintenance mode. For more information, see “Maintenance Mode” on page 395. Before you change settings, please see “About IP Addresses” on page 45. Making Automatic Settings 1. From the Main Menu, highlight Network Management and press Enter.
VTrak E-Class Product Manual Managing Fibre Channel Connections The Fibre Channel Management option appears only with VTrak Fibre Channel models.
Chapter 5: Management with the CLU Making Fibre Channel Port Settings To make Fibre Channel port settings: 1. From the Main Menu, highlight Fibre Channel Management and press Enter. 2. Highlight Fibre Channel Ports and press Enter. 3. Highlight the port you want and press Enter. 4. Highlight Fibre Channel Port Settings and press Enter. 5. Highlight the following parameters and press the spacebar to toggle though the choices: 6.
VTrak E-Class Product Manual Viewing Fibre Channel Port Statistics To view Fibre Channel port statistics: 1. 2. From the Main Menu, highlight Fibre Channel Management and press Enter. Highlight Fibre Channel Ports and press Enter. Highlight the port you want and press Enter. 3. Highlight Fibre Channel Port Statistics and press Enter. Viewing SFP Information To view information about the SFPs (small form-factor pluggable transceivers): 1.
Chapter 5: Management with the CLU • WordsSent – Number of words sent since last reset. • WordsReceived – Number of words received since last reset. • LIPCount – Loop Initialization Primitive Sequence. This primitive sequence applies only to the arbitrated loop topology. It is transmitted by an L_Port to initialize or re-initialize the loop. • NOSCount – Not Operational Primitive Sequence.
VTrak E-Class Product Manual To view Fibre Channel initiators: 1. From the Main Menu, highlight Fibre Channel Management and press Enter. 2. Highlight Fibre Channel Initiators and press Enter. A list of all currently logged-in initiators appears on the screen.
Chapter 5: Management with the CLU Managing iSCSI Connections The iSCSI Management option appears only with VTrak iSCSI models.
VTrak E-Class Product Manual A detailed explanation of iSCSI functions, how and when they are used, and their relationship to one another is beyond the scope of this document. For more information, contact the Internet Engineering Task Force at http://www.ietf.org/ Making Global iSCSI Settings Keep Alive recovers from intermittent disconnects that interrupt your iSCSI session. To make global iSCSI settings: 1. From the Main Menu, highlight iSCSI Management and press Enter. 2.
Chapter 5: Management with the CLU • TargetAlias – Maximum of 32 characters. Use letters, numbers, space between words, and underscore. An alias is optional.* • TargetStatus – Up or down. • ErrorRecovLevel – Error recovery level supported. • ImmediateData – Enables the initiator to send unsolicited data with the iSCSI command PDU. • MaxConnection – Maximum number of connections. • DataPDUInOrder – Enables placement of data in PDU order.
VTrak E-Class Product Manual Using the CLU, you must assign a portal to a target when you create the target. To add an iSCSI target: 1. 2. From the Main Menu, highlight iSCSI Management and press Enter. Highlight iSCSI Targets and press Enter. The list of iSCSI Targets displays. 3. Highlight Create New Target and press Enter. 4. Optional. Highlight TargetAlias and type an alias into the field provided. 5. Highlight each item and press the Spacebar to toggle between Enable and Disable.
Chapter 5: Management with the CLU • Optional. Highlight TargetAlias and type an alias into the field provided. • Highlight each item and press the Spacebar to toggle between Enable and Disable. • HeaderDigest – Adds a header digest (CRC). • DataDigest – Adds a data digest (CRC). • UniCHAPAuthen – Enables uni-directional CHAP authentication. • BiCHAPAuthen – Enables bi-directional CHAP authentication. Authentication requires a pre-existing CHAP. 6. Highlight Save Settings and press Enter.
VTrak E-Class Product Manual 1. 2. From the Main Menu, highlight iSCSI Management and press Enter. Highlight iSCSI Ports and press Enter. The list of ports appears with controller and port numbers. Viewing iSCSI Port Information To view information for an iSCSI target port: 1. 2. From the Main Menu, highlight iSCSI Management and press Enter. Highlight iSCSI Ports and press Enter. The list of ports appears with controller and port numbers. 3. Highlight the port you want to see and press Enter.
Chapter 5: Management with the CLU 8. Press Y again to confirm the changes. 9. Highlight Return to Previous Menu and press Enter to return to the target port information screen. Viewing a List of iSCSI Portals A portal is the interface between an iSCSI port and the iSCSI network. To view a list of iSCSI portals: 1. From the Main Menu, highlight iSCSI Management and press Enter. 2. Highlight iSCSI Portals and press Enter. The list of iSCSI Portals displays. • PortalId – Portal number. Starts at 0.
VTrak E-Class Product Manual • ProtocolFamily – IPv4 or IPv6.* • PrimaryIP – Primary IP address of this portal.* • PrimaryIPMask – Subnet mask of this portal.* • AssignedTarget – 0 is the default target. The number of targets available depends on how many targets you create. See “Adding iSCSI Targets” on page 259. Items marked with an asterisk (*) are adjustable under “Making iSCSI Portal Settings” on page 265. Adding iSCSI Portals VTrak supports up to 32 iSCSI portals per iSCSI port.
Chapter 5: Management with the CLU To change a value, highlight the item, press Backspace to delete the current value and type a new value. 8. Highlight Save Settings and press Enter. The new Portal is added to the list. Making iSCSI Portal Settings To make portal settings: 1. From the Main Menu, highlight iSCSI Management and press Enter. 2. Highlight iSCSI Portals and press Enter. The list of portals displays. 3. Highlight the portal you want to change and press Enter.
VTrak E-Class Product Manual 6. Press Y again to acknowledge possible interruption of iSCSI services. The portal is removed from the list. Viewing a List of iSCSI Sessions To view a list of iSCSI sessions: 1. From the Main Menu, highlight iSCSI Management and press Enter. 2. Highlight iSCSI Sessions and press Enter.
Chapter 5: Management with the CLU Viewing iSCSI Session Information To view a list of iSCSI sessions: 1. From the Main Menu, highlight iSCSI Management and press Enter. 2. Highlight iSCSI Sessions and press Enter. 3. Highlight the session you want and press Enter.
VTrak E-Class Product Manual Viewing iSCSI iSNS Information Internet Storage Name Service (iSNS) is a protocol used to facilitate the automated discovery, management, and configuration of iSCSI and Fibre Channel devices on a TCP/IP network. To view iSNS information: 1. 2. From the Main Menu, highlight iSCSI Management and press Enter. Highlight iSCSI iSNS Options and press Enter. The current iSNS options appear.
Chapter 5: Management with the CLU To view a list of iSCSI CHAPs: 1. From the Main Menu, highlight iSCSI Management and press Enter. 2. Highlight iSCSI CHAPs and press Enter. A list of the current CHAPs appears. Information includes: • ID – ID number. Numbering starts at 0. • Type – Peer is one-way. Local is bi-directional. • Name – Same as an alias. Adding iSCSI CHAPs Verify that CHAP authentication is enabled under “Making iSCSI Target Settings” on page 260. To add an iSCSI CHAP: 1.
VTrak E-Class Product Manual The edited CHAP appears in the list. Deleting iSCSI CHAPs To delete an iSCSI CHAP: 1. From the Main Menu, highlight iSCSI Management and press Enter. 2. Highlight iSCSI CHAPs and press Enter. 3. Highlight the CHAP you want to delete and press Enter to mark it. 4. Highlight Delete Marked Entries and press Enter. 5. Press Y to confirm the deletion.
Chapter 5: Management with the CLU • Slave Ports – Any or all of the remaining physical ports on the same RAID controller • Failed Ports – A slave port that has no iSCSI data connection. • State – Optimal, Sub-Optimal or Failed. Identify and correct the failed iSCSI ports. Adding iSCSI Trunks Ports must be enabled to add them to a trunk. See “Making iSCSI Port Settings” on page 262. VTrak supports a maximum of eight trunks. You cannot use an iSCSI port that has portals configured to it.
VTrak E-Class Product Manual You can choose any or all port numbers except the Master Port number. 5. Highlight Save Settings and press Enter. Deleting iSCSI Trunks Before you can delete a trunk, you must delete any portals configured on it. See“Deleting iSCSI Portals” on page 265. To delete an iSCSI trunk: 1. From the Main Menu, highlight iSCSI Management and press Enter. 2. Highlight Trunk and press Enter. 3. Highlight the trunk you want to delete and press the Spacebar to mark it. 4.
Chapter 5: Management with the CLU Managing Background Activity Background activity refers to any of several functions that take place in the background while normal operation of the VTrak continues. Background activities work in conjunction with disk arrays and logical drives. See “Managing Disk Arrays” on page 229 and “Managing Logical Drives” on page 242 for more information about how and when to use background activities.
VTrak E-Class Product Manual • PDM – Migrates data from a suspect physical drive to a replacement drive in a disk array • Transition – Returns a revertible spare drive to spare status • Synchronization – Checks the data integrity on disk arrays • Initialization – Full initialization sets all data bits in the logical drive to a specified pattern, such as all zeros • Redundancy Check – Checks, reports and can correct data inconsistencies in logical drives The rates are defined as follows: 5. 6.
Chapter 5: Management with the CLU Working with the Event Viewer Working with the Event Viewer includes the following functions: • Viewing Runtime Events (page 275) • Clearing Runtime Events (page 276) • Viewing NVRAM Events (page 276) • Clearing NVRAM Events (page 276) The Event Viewer displays log of subsystem events.
VTrak E-Class Product Manual Clearing Runtime Events To clear the Runtime Event log: 1. From the Main Menu, highlight Event Viewer and press Enter. 2. Highlight Clear Runtime Event Log and press Enter. 3. Press Y to confirm. Viewing NVRAM Events This screen displays a list of and information about the most important events over multiple subsystem startups. To display NVRAM events: 1. 2. From the Main Menu, highlight Event Viewer and press Enter. Highlight NVRAM Events and press Enter.
Chapter 5: Management with the CLU Working with LUN Mapping LUN Mapping includes the following functions: • Enabling LUN Mapping (page 277) • Viewing a List Ports (page 277) • Viewing a List Targets (page 278) • Viewing a List of Initiators (page 278) • Adding an Initiator (page 278) • Deleting an Initiator (page 279) • Viewing a List of LUN Maps (page 279) • Adding a LUN Map (page 280) • Editing a LUN Map (page 281) • Deleting a LUN Map (page 281) • Changing the Active LUN Mapping Typ
VTrak E-Class Product Manual 3. Highlight LUN Mapping: Ports and press Enter. A list of ports appears. Viewing a List Targets To view a list of iSCSI targets: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight LUN Mapping and press Enter. 3. Highlight LUN Mapping: Ports and press Enter. A list of ports appears. Viewing a List of Initiators LUN Mapping must be enabled in order for VTrak to recognize an initiator.
Chapter 5: Management with the CLU Obtain the initiator name from the initiator utility on your host system. Note that the initiator name you input must match exactly in order for the connection to work. 6. Highlight Save Initiator and press enter. The new initiator appears in the list. Deleting an Initiator Caution If you delete an initiator, you delete the LUN map associated with that initiator. Verify that the LUN map is no longer needed before deleting the initiator To delete an initiator: 1.
VTrak E-Class Product Manual Adding a LUN Map For FC systems, you can set up an Initiator or Port type LUN map. For iSCSI systems, you can set up an Initiator or Target type LUN map. You can set up both LUN map types on the same subsystem but only one LUN map type can be active at a time. A maximum of 1024 logical drives can be mapped to an FC initiator or port, or to an iSCSI initiator or target. To assign a LUN to an FC or iSCSI initiator, add the initiator first. See “Adding an Initiator” on page 278.
Chapter 5: Management with the CLU • Highlight LUN Mapping: Targets and press Enter. Then highlight a target and press Enter. A list of logical drives displays. 4. In the LUN field, press the backspace key to erase the current value, then type the LUN you want to assign to this target, from 0 to 255. Each logical drive can have only one LUN and must have a unique LUN. If you make a error, press Control-AR to restore the current LUN. 5. Press Control-A to save the LUN map.
VTrak E-Class Product Manual 3. Do one of the following actions: • Highlight LUN Mapping: Initiators and press Enter. Then highlight an initiator and press Enter. • Highlight LUN Mapping: Ports and press Enter. Then highlight a port and press Enter. • Highlight LUN Mapping: Targets and press Enter. Then highlight a target and press Enter. A list of logical drives displays. A list of logical drives displays. 4. In the LUN field, press the backspace key to erase the current value.
Chapter 5: Management with the CLU Managing UPS Units Uninterruptible Power Supply (UPS) Management includes the following functions: • Viewing a List of UPS Units (below) • Making UPS Settings (page 284) • Viewing UPS Information (page 285) Viewing a List of UPS Units To view a list of UPS units supporting the VTrak: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight UPS Management and press Enter.
VTrak E-Class Product Manual Making UPS Settings These settings control how the VTrak subsystem detects the UPS unit and responds to data reported by the UPS unit. To make UPS settings: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight UPS Management and press Enter. 3. Highlight UPS Settings and press Enter. 4. Perform the following actions as required: • • • • 5. Verify the Current UPS Communication method. See Note 1: • SNMP – Network connection.
Chapter 5: Management with the CLU Note 3: The maximum recommended Loading Ratio varies among models of UPS units. The general range is 60% to 80%. Note 4: To specify UPS units by DNS names, ask your IT administrator to add the DNS names to the DNS server, before you make UPS settings. Viewing UPS Information To view information about a specific UPS unit: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight UPS Management and press Enter. 3.
VTrak E-Class Product Manual Managing Users User Management includes the following functions: • Viewing User Information (page 286) • Creating a User (page 286) • Changing Another User’s Settings (page 287) • Changing Your Own User Settings (page 288) • Changing Another User’s Password (page 288) • Changing Your Own Password (page 288) • Deleting a User (page 289) Viewing User Information Each user types their user name and password to log into the CLI.
Chapter 5: Management with the CLU User Privileges Level Meaning View Allows the user to see all status and settings but not to make any changes Maintenance Allows the user to perform maintenance tasks including Rebuilding, PDM, Media Patrol, and Redundancy Check Power Allows the user to create (but not delete) disk arrays and logical drives, change RAID levels, change stripe size; change settings of components such as disk arrays, logical drives, physical drives, and the controller Super Allows t
VTrak E-Class Product Manual Changing Your Own User Settings Each user can change their display name and email address. To change your user settings: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight User Management and press Enter. 3. Highlight your name and press Enter. 4. Highlight the items you want and press the backspace key to erase the current value, then type the new value: 5. • User name • Email address Press Control-A to save the settings.
Chapter 5: Management with the CLU 2. Highlight User Management and press Enter. 3. Highlight your name and press Enter. 4. Highlight Change Password... and press Enter. 5. Highlight Old Password and type your current password. 6. Highlight New Password and type a new password. Maximum 31 characters. Use letters, numbers, and underscore. 7. Highlight Retype Password and type the new password again to verify. 8. Press Control-A to save the new password.
VTrak E-Class Product Manual Managing LDAP LDAP Management includes the following functions: • Viewing LDAP Information (page 290) • Making LDAP Settings (page 291) • Testing LDAP Settings (page 293) • Viewing a List of Role Maps (page 293) • Adding a Role Map (page 293) • Making Role Map Settings (page 294) • Deleting a Role Map (page 294) Viewing LDAP Information To view LDAP information: 1. 2. From the Main Menu, highlight Additional Info and Management and press Enter.
Chapter 5: Management with the CLU • Server Type – Windows Active Directory, Mac Open directory, or Unspecified. • Role Policy – Default or Explicit. • Default Privilege – Applies to Default Role Policy. The following items apply to the Default Role Policy. • BaseDNOfGroup – Authenticates communication between subsystem and LDAP server. • ObjectClassOfGroup – group is the default value. • GroupIDAttribute – cn is the default. Making LDAP Settings To make LDAP settings: 1. 2.
VTrak E-Class Product Manual Mac Open Directory and Unspecified set uid. 6. • FullNameAttribute – Store user’s full name in LDAP server. displayName is the default. • EmailAddrAttribute – Store user’s email address in LDAP server. mail is the default. Highlight each item and press the Spacebar to toggle through the options, as needed. • Server Type – Windows Active Directory, Mac Open directory, or Unspecified. • Role Policy – Default or Explicit.
Chapter 5: Management with the CLU Testing LDAP Settings To test your LDAP settings: 1. 2. From the Main Menu, highlight Additional Info and Management and press Enter. Highlight LDAP Management and press Enter. The LDAP Settings screen appears. 3. Highlight LDAP Auth and press Enter. The LDAP Authorization screen appears. LDAP must be enabled to test the settings. 4. Highlight Test and press Enter. Viewing a List of Role Maps A Role Map is a method of mapping a group of users to an LDAP server.
VTrak E-Class Product Manual 4. Highlight Create Role and press Enter. 5. Highlight External Role and type a name in the field provided. 6. Highlight Privilege and press the Spacebar to toggle through the privilege levels: View, Maintenance, Power, and Super. See Table 3 on page 292. 7. Press Control-A to save your settings. The new role appears in the list. Making Role Map Settings To make role map settings: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2.
Chapter 5: Management with the CLU Working with Software Management Software Management includes the following functions: • Making Email Settings (page 295) • Making SLP Settings (page 296) • Making Web Server Settings (page 296) • Making Telnet Settings (page 297) • Making SSH Settings (page 297) • Making SNMP Settings (page 298) • Managing SNMP Trap Sinks (page 298) • Making CIM Settings (page 299) • Making Netsend Settings (page 301) • Managing Netsend Recipients (page 301) Making Em
VTrak E-Class Product Manual To start, stop or restart the Email service, highlight Start, Stop or Restart and press Enter. Making SLP Settings By default, SLP service is set to Automatic and its normal status is Started. To make SLP service settings: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight Software Management and press Enter. 3. Highlight SLP and press Enter. 4.
Chapter 5: Management with the CLU Making Telnet Settings By default, Telnet service is set to Automatic and its normal status is Started. To make Telnet service settings: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight Software Management and press Enter. 3. Highlight Telnet and press Enter. 4. Highlight Startup Type and press the spacebar to toggle between Automatic and Manual. 5.
VTrak E-Class Product Manual Making SNMP Settings By default, Simple Network Management Protocol (SNMP) service is set to Automatic and its normal status is Started. To make SNMP service settings: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight Software Management and press Enter. 3. Highlight SNMP and press Enter. 4. Highlight Startup Type and press the spacebar to toggle between Automatic and Manual. 5.
Chapter 5: Management with the CLU 2. Highlight Software Management and press Enter. 3. Highlight SNMP and press Enter. 4. Highlight Trap Sinks and press Enter. 5. Highlight Create New Trap Sink and press Enter 6. Highlight Trap Sink IP address and press the backspace key to erase the current value, then type the new IP address in this field. 7. Highlight Trap Filter and press the spacebar to toggle through the severity levels. See the Table below. 8. Press Control-A to save the Trap Sink.
VTrak E-Class Product Manual To make CIM service settings: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight Software Management and press Enter. 3. Highlight CIM and press Enter. 4. Enter information or change settings as required. • Highlight Startup Type and press the spacebar to toggle between Automatic and Manual.
Chapter 5: Management with the CLU Making Netsend Settings By default, Netsend service is set to Manual and its normal status is Stopped. To make Netsend service settings: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight Software Management and press Enter. 3. Highlight Netsend and press Enter. 4. Highlight Startup Type and press the spacebar to toggle between Automatic and Manual. 5. Press Control-A to save your settings.
VTrak E-Class Product Manual The selected level and all higher severity levels of severity are reported. See the Table below. 8. Press Control-A to save your settings. Event Severity Levels Level Description Fatal Non-recoverable error or failure has occurred. Critical Action is needed now and the implications of the condition are serious. Major Action is needed now. Minor Action is needed but the condition is not a serious at this time.
Chapter 5: Management with the CLU Flashing through TFTP Use this function to flash (update) the firmware on the VTrak. See page 317 for the procedure.
VTrak E-Class Product Manual Viewing Flash Image Information Flash image information refers to the package of firmware components running on your VTrak controller or controllers. To view flash image information: 1. From the Main Menu, highlight Additional Info and Management, and press Enter. 2. Highlight Flash Image Version Info and press Enter. The flash image information displays on the screen: • Enclosure Number – 1 (one) is the Head Unit.
Chapter 5: Management with the CLU Clearing Statistics This function clears the statistical counts for the RAID controller, Fibre Channel ports, iSCSI ports, physical drives, and logical drives. To clear statistics: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight Clear Statistics and press Enter. 3. Press Y to confirm the deletion.
VTrak E-Class Product Manual Restoring Factory Defaults This function restores the factory default settings to the firmware and software items you select. Caution Restoring default settings can disrupt your VTrak functions. Use this feature only when necessary. If you restore Management Network settings, you lose your network connection to the VTrak. Note To reset the Administrator’s password to the factory default, see “Resetting the Default Password” on page 330. 1.
Chapter 5: Management with the CLU Shutting Down the Subsystem There are two methods for shutting down the subsystem. Choose one of the following procedures: • Shutting down the VTrak – Telnet Connection (page 307) • Shutting down the VTrak – SSH Connection (page 307) • Shutting down the VTrak – Serial Connection (page 308) Shutting down the VTrak – Telnet Connection This function shuts down the VTrak subsystem on a Telnet connection. Additional action is required, as described below.
VTrak E-Class Product Manual To shutdown the RAID subsystem: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight Shutdown or Restart and press Enter. 3. Highlight Option and press the spacebar to display Shutdown. 4. Highlight Submit and press Enter. A warning message appears. 5. Press Y to continue. 6. Close your SSH session. 7. Wait for no less than two minutes. 8. Manually turn off the power supply switches on the back of the subsystem.
Chapter 5: Management with the CLU Starting Up After Shutdown There are two methods for shutting down the subsystem. Choose one of the following procedures: • Starting up the VTrak – Telnet Connection (page 309) • Starting up the VTrak – SSH Connection (page 309) • Starting up the VTrak – Serial Connection (page 310) Starting up the VTrak – Telnet Connection Important If you have a JBOD Expansion, always power on the JBOD subsystems first. Then power on the RAID subsystem.
VTrak E-Class Product Manual Starting up the VTrak – Serial Connection Important If you have a JBOD Expansion, always power on the JBOD subsystems first. Then power on the RAID subsystem. To start the RAID subsystem: 1. Manually turn on the power supply switches on the back of the subsystem. 2. Wait about two minutes. 3. Establish a serial connection to the VTrak. See “Making a Serial Connection” on page 206. When the Login: prompt appears, the start up is finished. 4.
Chapter 5: Management with the CLU Restarting the Subsystem There are two methods for restarting the subsystem. Choose one of the following procedures: • Restarting the Subsystem (page 311) • Restarting VTrak – SSH Connection (page 311) • Restarting VTrak – Serial Connection (page 312) Note If you have a JBOD Expansion, you are not required to restart the JBOD subsystems when you restart the RAID subsystem. Restarting VTrak – Telnet Connection To restart the RAID subsystem: 1.
VTrak E-Class Product Manual 6. Close your SSH session. 7. Wait about two minutes. 8. Re-establish your SSH connection to the VTrak CLU. See “Making a SSH Connection” on page 207. If you cannot re-establish a connection, wait 30 seconds and try again. Restarting VTrak – Serial Connection To restart the RAID subsystem: 1. From the Main Menu, highlight Additional Info and Management and press Enter. 2. Highlight Shutdown or Restart and press Enter. 3.
Chapter 5: Management with the CLU Buzzer Making Buzzer Settings The buzzer sounds to inform you that the VTrak needs attention. See “VTrak is Beeping” on page 375 for more information. To make buzzer settings: 1. From the Main Menu, highlight Buzzer and press Enter. A list of Controllers appears with the current buzzer setting and status. 2. Highlight the Controller whose buzzer you want to set and press Enter. 3. Highlight Enabled and press the spacebar to toggle between Yes and No. 4.
VTrak E-Class Product Manual 314
Chapter 6: Maintenance This chapter covers the following topics: • Updating the Subsystem Firmware (below) • Updating Physical Drive Firmware (page 321) • Replacing a Power Supply (page 323) • Replacing a Cache Backup Battery (page 324) • Replacing a RAID Controller – Dual Controllers (page 326) • Replacing a RAID Controller – Single Controller (page 327) • Resetting the Default Password (page 330) Updating the Subsystem Firmware This procedure applies to VTrak RAID subsystems and VTrak JBOD e
VTrak E-Class Product Manual • 5. TFTP Server – Enter the TFTP Server host name or IP address, port number and file name. Optional. Check the Non-disruptive Image Update (NDIU) box. NDIU updates the RAID controllers and I/O modules one at a time, enabling I/O operations continue during the firmware update. Updates with this option take a longer period of time to complete. Only VTrak x30 models support this feature. 6. Click the Next button.
Chapter 6: Maintenance Updating with the CLU Download the latest firmware image file from PROMISE support: http://www.promise.com/support/ and save it to your Host PC or TFTP server. Important Verify that no background activities are running on the RAID subsystem. To update the firmware on the RAID subsystem and JBOD expansion units: 1. From the Main Menu, highlight Additional Info and Management, and press Enter. 2. Highlight Flash through TFTP and press Enter. 3.
VTrak E-Class Product Manual Automatic Restart If you chose the Disruptive Flash Method, the RAID subsystem and JBOD expansion units automatically restart. That action temporarily disrupts I/O operations and drops your CLU connection. After the screen goes blank, wait about two minutes, then re-establish your Telnet connection to the CLU. If you cannot re-establish a connection, wait 30 seconds and try again.
Chapter 6: Maintenance Updating with USB Support USB support uses the disruptive flash method only. Both RAID controllers and all JBOD I/O modules are updated at the same time and momentarily go offline when the RAID subsystem and JBOD unit reboot. This procedure requires a USB flash device: • Formatted to FAT 32 • At least 50 MB of free space Download the latest OPAS_xxxxx.sbb firmware image file from PROMISE support: http://www.promise.com/support/ and save it the root folder of the USB flash device.
VTrak E-Class Product Manual You can insert the USB flash device back into either USB port but it must be the same RAID controller as step 1. 4. Wait until the controller activity LED displays steady green. 5. Remove the USB flash device. Automatic Restart After you remove the USB flash device from the RAID controller, the RAID subsystem and any JBOD expansion units automatically restart. That action temporarily disrupts I/O operations and drops your WebPAM PROe or CLU connection.
Chapter 6: Maintenance Updating Physical Drive Firmware This feature applies only to PROMISE-supported physical drives. For a list of supported drives, go to PROMISE support: http://www.promise.com/support/. If you have physical drives in your RAID system that are not PROMISEsupported, follow the firmware update procedure from the drive manufacturer. WebPAM PROe Download the latest firmware image file from PROMISE support: http://www.promise.com/support/ and save it to your Host PC or TFTP server.
VTrak E-Class Product Manual Restarting a Subsystem This function shuts down the subsystem and then restarts it. Important Do NOT turn off the power supply switches on the RAID subsystem or JBOD expansion units. To restart the subsystem: 1. Click the Administration tab. 2. Click the Subsystem Information icon. 3. Click the Shutdown/Restart button. 4. Click the Restart button. 5. Type the word “confirm” in the field provided. 6. Click the Confirm button.
Chapter 6: Maintenance Replacing a Power Supply The power supply and its fans are replaced as one unit. There are no individually serviceable parts. No tools are required for this procedure. Removing the Old Power Supply To remove the power supply: 1. Verify that the status LED is amber or red. See Figure 2. 2. Switch off the power. 3. Unplug the power cord. 4. Turn the two set screws counter-clockwise to loosen them. The screws are retained on the power supply housing. 5.
VTrak E-Class Product Manual Replacing a Cache Backup Battery The cache backup battery, also called a Battery Backup Unit (BBU) powers the cache to preserve data that has not been written the physical drives. The battery is located inside the RAID controller. Each RAID controller has its own battery. Cautions • Try reconditioning the battery before you replace it. See “Reconditioning a Battery” on page 90 or page 223 for more information. • The battery assembly is replaced as a unit.
Chapter 6: Maintenance Figure 3.
VTrak E-Class Product Manual Replacing a RAID Controller – Dual Controllers The RAID controller monitors and manages the logical drives. When the RAID controller is replaced, all of your logical drive data and configurations remain intact because logical drive information is stored on the physical drives. Important • Do not replace the RAID controller based on LED colors alone. Only replace the RAID controller when directed to do so by PROMISE Technical Support. See page 435.
Chapter 6: Maintenance Figure 4. RAID controller release Release tab and handle Installing the New Controller To install the new RAID controller: 1. Carefully slide the RAID controller into the enclosure. 2. Gently swing the handle in and press the handle until it locks. 3. Reconnect all cables that were attached to the RAID controller.
VTrak E-Class Product Manual Important Do not replace the RAID controller based on LED colors alone. Only replace the RAID controller when directed to do so by PROMISE Technical Support. See page 435. Important The firmware on the replacement RAID controller must be the same version as the original RAID controller or a later version. The amount of SDRAM in the replacement RAID controller must be the same as the original RAID controller or greater.
Chapter 6: Maintenance The VTrak restarts. For more information about VTrak’s start-up behavior, see “Connecting the Power” on page 41. 5. Log into the VTrak. For more information, see “Logging into WebPAM PROe” on page 69 or “Initial Connection” on page 206.
VTrak E-Class Product Manual Resetting the Default Password This feature resets the Administrator’s password to the default factory setting, password. Use this feature when you have forgotten Administrator’s password or a new Administrator has been appointed. The reset applies to the Administrator’s login for WebPAM PROe, the CLI, and the CLU. No other user passwords are affected. To reset the Administrator’s default password: 1. Verify that the VTrak has fully booted.
Chapter 7: Technology Background This chapter covers the following topics: • Disk Arrays (below) • Logical Drives (page 333) • Spare Drives (page 355) • RAID Controllers (page 361) • iSCSI Management (page 366) • Internet Protocols (page 373) Disk Arrays Disk array technology includes: • Media Patrol (page 331) • PDM (page 331) • Power Management (page 332) Media Patrol Media Patrol is a routine maintenance procedure that checks the magnetic media on each disk drive.
VTrak E-Class Product Manual PDM constantly monitors your physical drives and automatically copies your data to a spare drive before the physical drive fails and your logical drive goes Critical. The following actions trigger PDM: • A phyical drive with unhealthy status (see below) • Media Patrol finds a critical error • You initiate PDM manually PDM also counts the number of media errors reported by Media Patrol.
Chapter 7: Technology Background Logical Drives Logical drive technology includes: • RAID Levels (page 333) • RAID Level Migration (page 347) • Stripe Size (page 353) • Sector Size (page 353) • Preferred Controller ID (page 353) • Initialization (page 354) • Partition and Format (page 354) RAID Levels RAID (Redundant Array of Independent Disks) allows multiple physical drives to be combined together in a disk array. Then all or a portion of the disk array is formed into a logical drive.
VTrak E-Class Product Manual Advantages • • • Disadvantages Implements a striped disk array, the data is broken down into blocks and each block is written to a separate disk drive I/O performance is greatly improved by spreading the I/O load across many channels and drives • Not a true RAID because it is not fault-tolerant • The failure of just one drive results in all data in an disk array being lost • Should not be used in mission critical environments No parity calculation overhead is involve
Chapter 7: Technology Background RAID 1 – Mirror When a logical drive is mirrored, identical data is written to a pair of physical drives, while reads are performed in parallel. The reads are performed using elevator seek and load balancing techniques where the workload is distributed in the most efficient manner. Whichever drive is not busy and is positioned closer to the data is accessed first.
VTrak E-Class Product Manual Advantages Disadvantages • • Simplest RAID storage subsystem design • Can increase read performance by processing data requests in parallel since the same data resides on two different drives Very high disk overhead – uses only 50% of total capacity Recommended Applications for RAID 1: • Accounting • Payroll • Financial • Any application requiring very high availability 336
Chapter 7: Technology Background RAID 1E – Enhanced Mirror RAID 1E offers the security of mirrored data provided by RAID 1 plus the added capacity of more than two physical drives. It also offers overall increased read/ write performance plus the flexibility of using an odd number of physical drives. With RAID 1E, each data stripe is mirrored onto two physical drives. If one drive fails or has errors, the other drives continue to function, providing fault tolerance. Figure 3.
VTrak E-Class Product Manual RAID 5 – Block and Parity Stripe RAID 5 organizes block data and parity data across the physical drives. Generally, RAID Level 5 tends to exhibit lower random write performance due to the heavy workload of parity recalculation for each I/O. RAID 5 is generally considered to be the most versatile RAID level. It works well for file, database, application and web servers. Figure 4.
Chapter 7: Technology Background RAID 6 – Block and Double Parity Stripe RAID level 6 stores dual parity data is rotated across the physical drives along with the block data. A RAID 6 logical drive can continue to accept I/O requests when any two physical drives fail. Figure 5. RAID 6 stripes all drives with data and dual parity Data Blocks Double Distributed (Wide-space Q+Q) Parity Physical Drives Hence, a RAID 6 logical drive with (7) 100 GB physical drives has a capacity of 500 GB.
VTrak E-Class Product Manual RAID 10 – Mirror + Stripe Mirror + Stripe combines both of the RAID 1 and RAID 0 logical drive types. RAID 10 can increase performance by reading and writing data in parallel or striping, and duplicating the data, or mirroring. PROMISE implements RAID 10 by creating a data stripe over one pair of disk drives, then mirroring the stripe over a second pair of disk drives. Some applications refer to this method as RAID 0+1. Figure 6.
Chapter 7: Technology Background Advantages Disadvantages • Implemented as a mirrored disk array whose segments are RAID 0 disk arrays • High I/O rates are achieved thanks to multiple stripe segments • Recommended Applications for RAID 10: • Imaging applications • Database servers • General fileserver 341 Very high disk overhead – uses only 50% of total capacity
VTrak E-Class Product Manual RAID 50 – Striping of Distributed Parity RAID 50 combines both RAID 5 and RAID 0 features. Data is striped across physical drives as in RAID 0, and it uses distributed parity as in RAID 5. RAID 50 provides data reliability, good overall performance, and supports larger volume sizes. Figure 7.
Chapter 7: Technology Background The chart below shows RAID 50 logical drives with 6 to 32 physical drives, the available number of axles, and the resulting distribution of physical drives on each axle. RAID 50 Logical Drive No. of Drives No. of Axles Drives per Axle No. of Drives No.
VTrak E-Class Product Manual Recommended Applications for RAID 50: • File and Application servers • Transaction processing • Office application with many users accessing small files 344
Chapter 7: Technology Background RAID 60 – Striping of Double Parity RAID 60 combines both RAID 6 and RAID 0 features. Data is striped across disks as in RAID 0, and it uses double distributed parity as in RAID 6. RAID 60 provides data reliability, good overall performance and supports larger volume sizes. Figure 8.
VTrak E-Class Product Manual RAID 60 Logical Drive No. of Drives No. of Axles Drives per Axle No. of Drives No.
Chapter 7: Technology Background RAID Level Migration The term “Migration” means either or both of the following: • Change the RAID level of a logical drive. • Expand the storage capacity of a logical drive. On VTrak, RAID level migration is performed on the disk array but it applies to the logical drives. Migration does not disturb your data. You can access the data while the migration is in progress. When migration is done, your disk array has a different RAID level and/or a larger capacity.
VTrak E-Class Product Manual RAID 0 A RAID 0 source logical drive can migrate to the following target logical drives: Target Requirements RAID 0 Add physical drives. RAID 1 2 physical drives only. Only a single-drive RAID 0 can migrate to RAID 1 by adding 1 physical drive. RAID 1E 3 or more physical drives. If existing physical drives have no unused space, add 1 or more physical drives. RAID 5 3 physical drives minimum, 32 maximum. RAID 0 must have less than 16 physical drives.
Chapter 7: Technology Background RAID 1 A RAID 1 Source logical drive can migrate to the following Target logical drives: Target Requirements RAID 0 None. RAID 1E 3 or more physical drives. Add 1 or more physical drives. RAID 5 3 physical drives minimum, 32 maximum. RAID 1 must have less than 32 physical drives. Add 1 or more physical drives. RAID 10 4 physical drives minimum. Even number of physical drives. Add 2 or more physical drives. RAID 50 6 physical drives minimum, 32 per axle maximum.
VTrak E-Class Product Manual RAID 5 A RAID 5 Source logical drive can migrate to the following Target logical drives: Target Requirements RAID 0 None. RAID 1E None. RAID 5 Add physical drives. 32 maximum. RAID 6 4 physical drives minimum, 32 maximum. If existing physical drives have no unused space, add 1 or more physical drives. RAID 10 4 physical drives minimum. Even number of physical drives. If existing physical drives have no unused space, add 1 or more physical drives.
Chapter 7: Technology Background RAID 10 A RAID 10 Source logical drive can migrate to the following Target logical drives: Target Requirements RAID 0 None. RAID 1E None. RAID 5 3 physical drives minimum, 32 maximum. RAID 10 must have less than 16 physical drives. RAID 6 4 physical drives minimum, 32 maximum. RAID 10 must have less than 32 physical drives. If existing physical drives have no unused space, add 1 or more physical drives. RAID 10 Add physical drives. Even number of physical drives.
VTrak E-Class Product Manual RAID 50 A RAID 50 Source logical drive can migrate to the following Target logical drives: Target Requirements RAID 0 None. RAID 1E None. RAID 5 32 physical drives maximum. RAID 50 must have less than 32 physical drives. RAID 6 32 physical drives maximum. RAID 50 must have less than 32 physical drives. If existing physical drives have no unused space, add 1 or more physical drives. RAID 10 Even number of physical drives. RAID 50 Add physical drives.
Chapter 7: Technology Background Stripe Size Stripe Size, also called “Stripe Block Size,” refers to the size of the data blocks written to, and read from, the physical drives. Stripe Size is specified when you create a logical drive. You can choose Stripe Size directly when you use the Wizard Advanced Configuration function to create a logical drive. You cannot change the Stripe Size of an existing logical drive. You must delete the logical drive and create a new one.
VTrak E-Class Product Manual Initialization Initialization is done to logical drives after they are created from a disk array. Full initialization sets all data bits in the logical drive to a specified pattern, such as all zeros. The action is useful because there may be residual data on the logical drives left behind from earlier configurations. For this reason, Initialization is recommended for all new logical drives. See “Initializing a Logical Drive” on page 167 or page 245.
Chapter 7: Technology Background Spare Drives Spare drive technology includes: • Definition (page 355) • Options (page 355) • Requirements (page 355) • Transition (page 356) Definition A spare drive is a physical drive that you designate to automatically replace the failed physical drive in a disk array. See “Creating a Spare Drive Manually” on page 173.
VTrak E-Class Product Manual A revertible spare drive requires: • You to replace the failed physical drive in the disk array • You to run the Transition function Transition Transition is the process of replacing a revertible spare drive that is currently part of a disk array with an unconfigured physical drive or a non-revertible spare. The revertible spare drive returns to its original status. In order to run the Transition function, the spare drive must be revertible.
Chapter 7: Technology Background Example Following is an example to explain the Transition function. 1 2 Array Drives 3 4 5 Spare Drive 6 In the example above, there is a four-drive RAID 5 disk array and a global spare drive. Physical drives 1, 2, 3, and 4 belong to the disk array. Physical drive 5 remains unconfigured. Physical drive 6 is a revertible spare drive.
VTrak E-Class Product Manual drive. In this example, physical drive 3 failed and the array is rebuilt using physical drive 6, the revertible spare drive. 1 2 Array Drives 3 4 5 6 When the rebuild is complete, the spare drive has replaced the failed drive. In this example, failed drive 3 was replaced by spare drive 6. The disk array now consists of physical drives 1, 2, 4, and 6. There is no spare drive at this moment.
Chapter 7: Technology Background Automatic Transition At this juncture, you would replace the failed drive in slot 3 with a new one of the same or greater capacity.
VTrak E-Class Product Manual 1 2 Array Drives 3 4 5 Spare Drive 6 When the Manual Transition is finished, physical drives 1, 2, 4, and 5 belong to the disk array and physical drive 6 is a revertible spare drive. At this point, you would replace the drive in slot 3. The new drive in slot 3 remains unconfigured until you assign it to a disk array or as a spare.
Chapter 7: Technology Background RAID Controllers RAID controller technology includes; • LUN Affinity (page 361) • ALUA (page 361) • Cache Policy (page 362) • Preferred Controller ID (page 364) • Power Saving (page 364) • Capacity Coercion (page 364) LUN Affinity VTrak subsystems with dual RAID controllers include a LUN Affinity feature. Normally, either controller can access all logical drives. LUN Affinity enables you to specify which controller can access each logical drive.
VTrak E-Class Product Manual Cache Policy As it is used with VTrak, the term cache refers to any of several kinds of highspeed, volatile memory that hold data moving from your computer to the physical drives or vice-versa. Cache is important because it can read and write data much faster than a physical drive. There are read caches, which hold data as it is read from a physical drive; and write caches, which hold data as it is written to a physical drive.
Chapter 7: Technology Background The Forced Read-Ahead cache policy setting provides predictive pre-fetching of data requests, allowing the controller to aggressively buffer large chunks of data in cache memory to prevent frame drops on high-bandwidth video playback. Not normally enabled for non-video applications. Adaptive Writeback Cache On the VTrak subsystem, you can set the logical drive write cache policy to Write Thru or Write Back.
VTrak E-Class Product Manual Preferred Controller ID See “Preferred Controller ID” on page 353. Power Saving Power saving is a method of conserving energy by applying specific actions to hard disk drives (HDD). After an HDD has been idle for the set period of time, you can elect to: • Park the read/write heads – Referred to as Power Saving Idle Time on VTrak. • Reduce disk rotation speed – Referred to as Power Saving Standby Time on VTrak.
Chapter 7: Technology Background replacement drive that is slightly smaller (within 1 gigabyte) than the remaining working drive. For example, the remaining working drives can be 80.5 GB and the replacement drive can be 80.3, since all are rounded down to 80 GB. This permits the smaller drive to be used. Without capacity coercion, the controller does not permit the use of a replacement physical drive that is slightly smaller than the remaining working drives.
VTrak E-Class Product Manual iSCSI Management iSCSI management uses the following terms: • Basic iSCSI (page 366) • iSCSI on a VLAN (page 368) • Initiator (page 369) • Target (page 370) • Portal (page 371) • Port (page 371) • Trunk (page 372) • Session (page 372) • iSNS (page 372) • CHAP (page 372) • Ping (page 373) Also see “Managing iSCSI Connections” on page 188 or page 257. A detailed explanation of iSCSI functions and how to best use them is beyond the scope of this document.
Chapter 7: Technology Background See “Adding an iSCSI Initiator” on page 178 or page 278. For more information, see: • “Managing iSCSI Connections” on page 188 or page 257 • “iSCSI Management” on page 366 • Visit the Promise Knowledgebase at http://kb.promise.com/ and access topic “10188 – Setting up Microsoft iSCSI Initiator With the VTrak” Figure 9.
VTrak E-Class Product Manual iSCSI on a VLAN VTrak supports up to 32 iSCSI portals per iSCSI port. Each iSCSI portal can belong to a different VLAN for a maximum of 32 VLANs. See the diagram on page 335, Figure 2. To set up the VTrak subsystem for a VLAN: 1. Add a new portal with a VLAN association. See “Adding iSCSI Portals” on page 194 or page 264. Note which iSCSI port you chose for the portal. 2. Add a new target. See “Adding iSCSI Targets” on page 190 or page 259. 3.
Chapter 7: Technology Background Figure 10.iSCSI VLAN map Building A Building B VLAN 2 regular network VLAN 2 regular network VLAN 1 iSCSI data network VLAN 1 iSCSI data network Network router Network router Network switch To switch Ethernet Port 1 Ethernet Port 2 Bound to Portal 1 To switch To switch Ethernet Port 3 Bound to Portal 2 Ethernet Port 4 Bound to Portal 3 Bound to Portal 4 Initiator An initiator functions as the client, in this case, your host PC or server.
VTrak E-Class Product Manual Each initiator has a unique iSCSI qualified name (IQN). You specify the initiator by that name when you map a LUN or logical drive to the initiator. Initiators come in two varieties, software and hardware. Software A software initiator uses code to implement iSCSI. The software emulates SCSI devices for a computer by speaking the iSCSI protocol.
Chapter 7: Technology Background CHAPs Challenge Handshake Authentication Protocol (CHAP) is an authentication mechanism used to authenticate iSCSI sessions between initiators and targets. A uni-directional or peer CHAP authenticates from the target (VTrak) to the initiator (host PC or server). A bi-directional or local CHAP authenticates target to initiator and initiator to target. Portal A portal is the logical point of connection between the VTrak and the iSCSI network.
VTrak E-Class Product Manual Trunk A trunk is an aggregation of two or more iSCSI ports on the same RAID controller. Also known as a link aggregation. This feature combines ports to increase bandwidth. Ports must be enabled to add them to a trunk. Trunks are identified by their Trunk IDs. When you create a trunk, you specify: • Controller ID – RAID controller whose iSCSI ports you are using. • Master port – Any available iSCSI port. • Slave ports – The remaining available iSCSI ports.
Chapter 7: Technology Background A uni-directional or peer CHAP authenticates from the target (VTrak) to the initiator (host PC or server). A bi-directional or local CHAP authenticates target to initiator and initiator to target. Ping Ping is a computer network administration utility that tests whether a device is accessable over the IP network. Ping sends echo request packets to the target node, such as your host PC or server, and waits for a response.
VTrak E-Class Product Manual 374
Chapter 8: Troubleshooting This chapter contains the following topics: • VTrak is Beeping (below) • LEDs Display Amber or Red (page 377) • CLU Reports a Problem (page 382) • WebPAM PROe Reports a Problem (page 385) • USB Support Reports a Problem (page 390) • Enclosure Problems (page 391) • RAID Controller Problems (page 395) • Disk Array and Logical Drive Problems (page 400) • Physical Drive Problems (page 399) • Connection Problems (page 405) • Power Cycling the Subsystem (page 409)
VTrak E-Class Product Manual • Check for yellow ! • Check the event log. red X icons. See “Viewing Runtime Events” on page 382 and “Viewing NVRAM Events” on page 382. When a continuous tone sounds, there are multiple alarm patterns sounding at the same time. Silencing the Buzzer Caution This action disables the buzzer for all events. To silence the buzzer: 1. Click the Device tab. 2. Click the Component List icon. 3. Click the Buzzer and click the Settings button. 4.
Chapter 8: Troubleshooting LEDs Display Amber or Red LEDs are used on VTrak’s: • Front Panel LEDs (page 377) • Drive Carrier LEDs (page 378) • Back Panel LEDs (page 379) Front Panel LEDs When the power is switched on, the LEDs on the front of the VTrak light up. Figure 1.
VTrak E-Class Product Manual See the table below. Enclosure Front LEDs State Power FRU Logical Drive Controller Activity Controller Heartbeat Dark No power No power — No Activity — Steady Green Normal Normal Normal — — Blinking Green — — — — Normal** Flashing Green — — — Activity — Amber — Problem* Critical — — Red — Failure* Offline — — * Check the LEDs on the back of the VTrak enclosure.
Chapter 8: Troubleshooting Figure 2.
VTrak E-Class Product Manual Figure 3. FC RAID controller LEDs Dirty cache LED Controller status LED Battery status LED Figure 4. iSCSI RAID controller LEDs Dirty cache LED Controller status LED Battery status LED Under normal conditions, the power supply status LEDs display green. Figure 5.
Chapter 8: Troubleshooting Enclosure Back LEDs State Power Supply Status Dirty Cache Battery No power Normal No power or Failed No power Steady Green Normal — Normal Normal Blinking Green Locator feature Locator feature — Locator feature Dark Steady Amber Flashing Amber Steady Red Flashing Red Surviving Unsaved data Less than 72 in cache hours reserve — — Normal — — Failed — Failed Failed Maintenance Mode — — — See “Enclosure Problems” on page 391 and “RAID Controller Pr
VTrak E-Class Product Manual CLU Reports a Problem The CLU reports information passively, that is you must determine which functions to check based on the sound of the VTrak’s audible alarm and any amber or red LEDs. See “VTrak is Beeping” on page 375 and “LEDs Display Amber or Red” on page 377 for more information. Check the event logs first. Then check the reported component. Viewing Runtime Events To display Runtime Events: 1. From the Main Menu, highlight Event Viewer and press Enter.
Chapter 8: Troubleshooting The log of NVRAM Events appears. Events are added to the top of the list. Each item includes: 3. • Sequence number – Begins with 0 at system startup. • Device – Disk Array, Logical Drive, Physical Drive by its ID number. • Severity – See the Table on the previous page. • Timestamp – Date and time the event happened. • Description – A description of the event in plain language. Press the up and down arrow keys to scroll through the log.
VTrak E-Class Product Manual Restore Settings [CTRL-R] Return to Previous Menu From this screen: • Highlight Physical Drives in the Array and press Enter to identify the failed disk drive • Highlight Rebuild and press Enter to rebuild the array after you replace the failed disk drive For more information, see “Enclosure Problems” on page 391.
Chapter 8: Troubleshooting WebPAM PROe Reports a Problem WebPAM PROe reports these conditions in the header and all four tabs. Header The Header displays popup messages, per your configuration.
VTrak E-Class Product Manual • Event Information Event Severity Levels Level Description Fatal Non-recoverable error or failure has occurred. Critical Action is needed now and the implications of the condition are serious. Major Action is needed now. Minor Action is needed but the condition is not a serious at this time. Warning User can decide whether or not action is required. Information Information only, no action is required. Device Tab • Front View, showing the drive carrier icons.
Chapter 8: Troubleshooting • Rear View, with Show Internal Components option. Battery Failure Overheating Power Supply Offline • Physical Drive View, physical drive shown dead or offline and marked with a red X icon.
VTrak E-Class Product Manual Storage Tab • Disk Arrays Disk Array Offline • Disk Array Rebuilding Logical Drives Logical Drive Rebuilding Logical Drive Offline 388
Chapter 8: Troubleshooting Administration Tab Events icon. Event Severity Levels Level Description Fatal Non-recoverable error or failure has occurred. Critical Action is needed now and the implications of the condition are serious. Major Action is needed now. Minor Action is needed but the condition is not a serious at this time. Warning User can decide whether or not action is required. Information Information only, no action is required.
VTrak E-Class Product Manual USB Support Reports a Problem This procedure requires a USB flash device: • Formatted to FAT 32 • At least 50 MB of free space Caution Verify that there is no firmware image file on the USB flash device. If a firmware image file is present, the RAID controller might attempt a firmware update. See page 319. To collect a service report using the USB Support feature: 1. Insert the USB flash device into one of the USB ports on one of the RAID controllers.
Chapter 8: Troubleshooting Enclosure Problems Enclosure Problems include: • Diagnosing an Enclosure Problem (below) • Overheating (page 393) • Power Supplies (page 393) • Batteries (page 394) Diagnosing an Enclosure Problem Check System Status on the Dashboard tab. If a yellow ! appears in the System Status box: or red X 1. icon. Click the name link of the component with the red X Click the link beside the red X icon The Components List of the Device tab displays. 2.
VTrak E-Class Product Manual Click the View button Note the red X icon The components list expands and shows the power supply fans, which server as the Cooling Unit of the VTrak Ex30 enclosure. Note the red X icons Note that the fans for power supply 2 (PSU 2) have failed. 3. 4. Click the Back View icon on the Device tab. Click the picture of the enclosure. A popup messages displays the status of each component. When a power supply fan fails, you must replace the power supply.
Chapter 8: Troubleshooting Overheating Overheating is a potentially serious condition because the excessively high temperatures can lead to physical drive failure and controller malfunction. Overheating usually results from: • Fan failure • Inadequate air circulation around the enclosure Fan Failure In the Ex30 series VTrak subsystems, the power supply fans are the Cooling Units for the enclosure. When a power supply fan fails, you must replace the power supply.
VTrak E-Class Product Manual Batteries The RAID controllers in the VTrak subsystem use a battery for backup power to protect data in the cache. Should a power failure occur, the battery enables the cache to hold data up to 72 hours. The battery recharges during normal subsystem operation. In most cases, installing a replacement battery corrects a marginal or failed condition. The battery is located inside the RAID controller housing.
Chapter 8: Troubleshooting RAID Controller Problems RAID controller problems include: • Maintenance Mode (page 395) • Finding and Correcting the Cause of the Problem (page 395) • Taking a RAID Controller out of Maintenance Mode (page 396) • Unsaved Data in the Controller Cache (page 398) Controller problems occur when one of the controllers goes into maintenance mode.
VTrak E-Class Product Manual Internal Checks If all external checks are OK, take the following actions: 1. Shut down the VTrak. See page 83 (WebPAM PROe) or page 248 (CLU). 2. Remove one of the RAID controllers. See “Replacing a RAID Controller – Dual Controllers” on page 326. 3. Restart the VTrak. 4. After the VTrak is fully booted, view the controller information. See page 85 (WebPAM PROe) or page 215 (CLU). 5.
Chapter 8: Troubleshooting 2. 3. • Stop bits: 1 • Flow control: none Start your PC’s terminal VT100 or ANSI emulation program. Press Enter once to launch the CLI. The login screen appears. The following steps show the default Administrator user name and password. Use your own user name and password if you have changed these. 4. At the Login prompt, type administrator and press Enter. 5. At the Password prompt, type password and press Enter. The CLI screen appears.
VTrak E-Class Product Manual The controller reboots. The Telnet session ends. Unsaved Data in the Controller Cache The dirty cache LED (marked with the icon) informs you that there is data in the cache that has not been saved to non-volatile memory. Such data is sometimes called “dirty,” not to suggest it is corrupted in some way but because it has not been saved to a physical drive. Figure 6.
Chapter 8: Troubleshooting Physical Drive Problems Physical drives are the foundation of data storage. A physical drive problem can affect your entire RAID system. When a yellow ! icon or a red X check the drive's operational status: icon appears beside a physical drive, 1. Click the Device tab. 2. Click the Physical Drive icon. 3. Click the physical drive you want, then click the View button. Look under Operational Status for the condition of the physical drive.
VTrak E-Class Product Manual Disk Array and Logical Drive Problems Disk array and logical drive problems include: • Disk Array Degraded/Logical Drive Critical (page 400) • Disk Array Offline/Logical Drive Offline (page 401) • Repairing an Offline Disk Array or Logical Drive (page 402) • Rebuilding a Disk Array (page 402) • Incomplete Array (page 403) Disk array problems typically result from a physical drive failure. The most common problem is a degraded disk array.
Chapter 8: Troubleshooting • Degraded with a yellow ! • Critical with a yellow ! icon when ONE physical drive is offline. icon when TWO physical drives are offline. RAID 0 logical drives show Offline status and a red X icon. If there is no spare drive or unconfigured drive in the RAID system, you must provide the replacement drive. See “Installing Physical Drives” on page 21.
VTrak E-Class Product Manual Under Background Activities, no Rebuild takes place. See Repairing, below. The system sends an Email message about the incident to subscribing users, depending on user settings. See “Setting User Event Subscriptions” on page 103. Repairing an Offline Disk Array or Logical Drive RAID 1, 1E, 5, 6, 10, 50, and 60 Logical Drives If a fault-tolerant logical drive, RAID 1, 1E, 5, 6, 10, 50, and 60, goes Offline, it may be possible to recover your data.
Chapter 8: Troubleshooting • If there is no spare drive of adequate capacity and the Auto Rebuild function is DISABLED, you must replace the failed drive with an unconfigured physical drive, then perform a Manual Rebuild. See “Rebuilding a Disk Array” on page 160. Important If your replacement disk drive was formerly part of a different disk array or logical drive, you must clear the configuration data on the replacement drive before you use it. See “Clearing a Stale or a PFA Condition” on page 147.
VTrak E-Class Product Manual 2. 3. Check the operational status of the logical drives in the array. • If the logical drives are Critical, proceed with a rebuild. • If the logical drives are Offline, contact Technical Support. See page 435. Restore your data from a backup source. If you choose NOT to accept the incomplete array: 1. 2. Click Cancel in the incomplete array dialog box. Do one of the following: • Delete the array. This action deletes all logical drives on the array.
Chapter 8: Troubleshooting Connection Problems Connection problems include: • Serial Connections (page 405) • Network Connections (page 406) • Fibre Channel Connections (page 406) • SAS Connections (page 407) • Browser Does Not Connect to WebPAM PROe (page 408) Connection problems cause a majority of failures in almost any electrical system.
VTrak E-Class Product Manual Network Connections Each RAID controller has an Ethernet (RJ45) management port connector on the back of the enclosure. This is a Gigabit Ethernet connector designed to connect to your network. The VTrak becomes a node on your network like any other PC, server or other component with an IP address. VTrak ships from the factory IP addresses of 10.0.0.1, 10.0.0.2, and 10.0.0.3. You must change these addresses to ones that work on your network.
Chapter 8: Troubleshooting If VTrak sees some initiators but not the one you want, the problem is most likely elsewhere in the loop or fabric. If VTrak does not see any initiators: • Check all of the Fibre Channel connections • Verify that all nodes are properly connected and powered • Verify that the fabric router or switch is properly connected powered For more information, see “Managing Fibre Channel Connections” on page 184 or page 252.
VTrak E-Class Product Manual administrator@cli> sasdiag -a errorlog -l expander -e 1 -i 1 3. At the command prompt, type the following command and press Enter. administrator@cli> sasdiag -a errorlog -l c2cport By interpreting the two error logs, you can verify which controller or I/O module SAS port is accumulating link errors.
Chapter 8: Troubleshooting Power Cycling the Subsystem To power cycle a RAID subsystem means to: • Shut down • Turn off the power • Turn on the power • Restart Power cycling is sometimes required as a remedial action but only when prompted by a message from software or when directed by Technical Support. To power cycle the RAID subsystem: 1. Shut down the subsystem. See “Shutting Down the Subsystem” on page 83 or page 307. When the controllers shut down, your network connection is lost. 2.
VTrak E-Class Product Manual Event Notification Response When you choose Event Notification, WebPAM PROe sends popup and/or email messages regarding its status. The messages you see depend on your notification selection and what is currently happening in the VTrak. See “Setting User Event Subscriptions” on page 103.
Chapter 8: Troubleshooting Reported Event Corrective Action Battery Battery is inserted No action is required. Battery charging has failed Replace the battery. Battery reconditioning has started No action is required. Battery reconditioning has been terminated Replace the battery. The write policy of writeback logical drive switched from writeback to writethru Check the event log to see whether battery is re-conditioning.
VTrak E-Class Product Manual Reported Event Corrective Action Controller The controller parameter(s) are changed by user No action is required. The controller is reset by Watch Dog timer Result of a firmware update. If the condition persists, replace the controller. The controller has new crash information Contact Tech Support. The controller’s heart beat has started The controller’s heart beat has stopped The partner controller’s heart beat has started No action is required.
Chapter 8: Troubleshooting Reported Event Corrective Action Controller is started Controller is set to Active Mode No action is required. Controller is set to Standby Mode Controller Failed Over as partner is removed Verify that the partner controller is properly installed and all cables are connected. Controller Failed Over as heart beat stopped Controller Firmware mismatch with that Auto Firmware synchronization of the partner controller upgrades or downgrades the firmware.
VTrak E-Class Product Manual Reported Event Corrective Action Controller was placed on reset during Fail Over processing Partner Controller was placed on reset during Fail Over processing No action is required. Controller was reset as it was not able to join the running partner controller Verify that the controller is running. If the condition persists, replace the controller.
Chapter 8: Troubleshooting Reported Event Corrective Action Drive-interface diagnostics has passed No action is required. Drive-interface diagnostics has failed Restart the VTrak. If this message appears repeatedly, contact Tech Support. Drive-interface controller has generated a general parity error If this message appears repeatedly, Drive-interface controller has generated contact Tech Support. a data parity error Enclosure Enclosure temperature is above the threshold Check blowers and fans.
VTrak E-Class Product Manual Reported Event Corrective Action Fibre Channel link is up Fibre Channel link is down No action is required. Fibre Channel controller settings have changed Firmware Update Firmware update is started No action is required. Firmware update is complete Firmware update is fail Try the update again. If this message repeats, contact Tech Support.
Chapter 8: Troubleshooting Reported Event Corrective Action Host interface controller has received a “clear task set” command. Host interface controller has received a “LUN reset” command. No action is required. Host interface controller is informed that the initiator has detected an error Host interface controller has received illegal secondary identification If this message appears repeatedly, Host interface controller has received a contact Tech Support.
VTrak E-Class Product Manual Reported Event Corrective Action JBOD JBOD system connected No action is required. JBOD system either is removed or malfunctioned Check Expander firmware and SAS connections. Logical Drive Logical drive initialization has started Logical drive Initialization is in progress No action is required. Logical drive initialization has completed Logical drive initialization has paused Resume the initialization when ready.
Chapter 8: Troubleshooting Reported Event Corrective Action Quick logical drive initialization is queued A new logical drive has been created No action is required. Logical drive has been deleted Logical drive has been placed online Logical drive has been placed online. Possible data loss Logical drive has been set to critical. Check the state of the physical drives, replace any bad drives. Rebuild logical drive.
VTrak E-Class Product Manual Reported Event Corrective Action Online capacity expansion has resumed No action is required. Online capacity expansion has stopped If this action was not intentional, check the logical drive’s status. Online capacity expansion has encountered a physical disk error Check the physical drive check table after OCE is finished. Online capacity expansion is aborted due to an internal error. Reduce system load on the VTrak.
Chapter 8: Troubleshooting Reported Event Corrective Action Physical disk assigned as global spare Global Spare has been deleted Physical Disk is no longer assigned as a global spare Physical disk assigned as dedicated spare No action is required. Dedicated Spare has been deleted Physical Disk is no longer assigned as a dedicated spare Physical disk has been inserted Physical disk has been removed Insert the physical drive back into the system.
VTrak E-Class Product Manual Reported Event Corrective Action A physical drive page 0 settings have been changed A physical drive page 1 settings have been changed (SATA drives) No action is required. A physical drive page 3 settings have been changed (SAS drives) Physical disk is marked as DEAD due to removal Physical disk is marked as DEAD due to failure of reassign sectors command Physical disk is marked as DEAD due to PFA condition Replace the physical drive.
Chapter 8: Troubleshooting Reported Event Corrective Action PSU 12V/5V/3.3V power is within the normal range No action is required. PSU is critical. This may cause instability of the system Check the power to the PSU. Verify that the correct PSU is installed. PSU Fans PSU fan or blower has turned on PSU fan or blower has turned off PSU fan or blower speed is increased No action is required. PSU fan or blower speed is decreased PSU fan or blower is malfunctioning Replace the power supply.
VTrak E-Class Product Manual Reported Event Corrective Action Migration has cleared stale NV Watermark No action is required. Array was made incomplete due to missing NV Watermark If the array is online, try migration again. If the array is offline, delete and recreate the array. User has accepted Incomplete Array. (Caused by a missing NV Watermark) Rebuild the disk array. Rebuild Rebuild is started Rebuild is in progress No action is required.
Chapter 8: Troubleshooting Reported Event Corrective Action Redundancy Check task is stopped internally Restore the disk array to functional status. Redundancy check is started on unsynchronized logical drive No action is required. Resource Resource is NOT available Reduce system load on the VTrak. SCSI SCSI host interface controller settings have changed No action is required. SEP SEP is found No action is required. SEP is NOT found Insert or replace SEP hardware.
VTrak E-Class Product Manual Reported Event Corrective Action Stripe Level Migration Stripe Level migration is started No action is required. Stripe Level migration is completed Stripe Level migration is paused Resume SLM when ready. Stripe Level migration is resumed No action is required. Stripe Level migration is stopped If this action was not intentional, check the logical drive’s status.
Chapter 8: Troubleshooting Reported Event Corrective Action Transition Transition is started No action is required. Transition is completed Transition is paused Resume transition when ready. Transition is resumed No action is required. Transition is stopped If this action was not intentional, check the disk array’s status. Transition was switched to rebuild Replace the dead physical drive or reinstall the missing drive.
VTrak E-Class Product Manual 428
Chapter 9: Support This chapter contains the following topics: • Frequently Asked Questions (below) • Contacting Technical Support (page 435) • Limited Warranty (page 440) • Returning the Product For Repair (page 442) Frequently Asked Questions Physical Drives What kind of disk drives can I use with VTrak? VTrak E-Class supports: • 3.5-inch and 2.
VTrak E-Class Product Manual I can access the VTrak over my company’s intranet. But I can’t access it from an outside Internet connection. How do I make the Internet connection work? This condition is not related to VTrak, but is due to your firewall and network connection protocol. Contact your MIS Administrator. Why can a RAID 1 logical drive on VTrak consist of only two disk drives? RAID 1 logical drives work in mirrored physical drive pairs. You could create up to eight RAID 1 logical drives.
Chapter 9: Support What happens if a fan fails? If the system reports a fan malfunction, contact Technical Support (see page 435) immediately to schedule replacement of the suspect power supply as soon as possible. Running the unit in this condition for more than three weeks may shorten subsystem life and void your warranty. What happens if a logical drive goes critical? On the front of VTrak, the logical drive LED turns amber and the buzzer sounds (if enabled).
VTrak E-Class Product Manual Be sure you are using the correct IP address and entry text for the VTrak RAID subsystem. For more information, see “Logging into WebPAM PROe” on page 69. I verified the IP address and entry text but I still cannot connect. Check the physical network connections on the VTrak RAID subsystem. If these are OK, report the problem to your network administrator. I can access the VTrak over my company's intranet. But I can’t access it from an outside Internet connection.
Chapter 9: Support If you are the Administrator or a Super User and cannot create a User, be sure the user name is not already in use. If you still cannot create a User, contact Technical Support. See page 435. Can I change my access rights? Only the Administrator or a Super User can change user access rights. See page 104 or page 287. Lock Person “xyz” set the lock and is not available. How do I unlock it? Ask your Administrator to release the lock.
VTrak E-Class Product Manual Deleting a Disk Array or Logical Drive Why can’t I select Delete Disk Array or Delete Logical Drive? You must have Power or Super User Rights to delete a disk array or logical drive. See your Administrator about upgrading your access rights, if necessary. Also see “Making User Settings” on page 104 or page 287. Can I delete a Logical Drive without deleting the Disk Array? Yes. See “Deleting a Logical Drive” on page 166.
Chapter 9: Support Contacting Technical Support PROMISE Technical Support provides several support options for PROMISE users to access information and updates. We encourage you to use one of our electronic services, which provide product information updates for the most efficient service and support. PROMISE E-Support: https://support.promise.com PROMISE web site: http://www.promise.
VTrak E-Class Product Manual EMEA Netherlands Science Park Eindhoven 5228 5692 EG Son, The Netherlands Apple Pre-Sales Toll Free Phone (0830 to 1700): 0800-917-027 Apple Support Phone (0830 to 1700) Toll Free: 0800-917-027 Apple Support Phone (After Hours, English only) Toll Free: 0800-917-027 Fax: +31 (0) 40-256-9463 Apple Sales Email: apple@promise.com Technical Support (E-Support): https://support.promise.com Web site: http://www.promise.
Chapter 9: Support Sweden Apple Pre-Sales Toll Free Phone (0830 to 1700): 020-797-720 Apple Support Toll Free Phone (0830 to 1700): 020-797-720 Apple Support Toll Free Phone (After Hours, English only): 020-797-720 Apple Sales Email: apple@promise.com Technical Support (E-Support): https://support.promise.com Web site: http://www.promise.
VTrak E-Class Product Manual Luxembourg Apple Pre-Sales Toll Free Phone (0830 to 1700): 0800-26425 Apple Support Toll Free Phone (0830 to 1700): 0800-26425 Apple Support Toll Free Phone (After Hours, English only): 0800-26425 Apple Sales Email: apple@promise.com Technical Support (E-Support): https://support.promise.com Web site: http://www.promise.
Chapter 9: Support Korea Apple Pre-Sales Toll Free (24x7 English only): 00798-14-800-7784 Apple Support Phone Toll Free (24x7 English only): 00798-14-800-7784 Apple Sales Email: apple@promise.com Technical Support (E-Support): https://support.promise.com Web site: http://www.promise.com/apple/ Hong Kong Apple Pre-Sales Toll Free Phone (24x7 English only): 800-933-480 Apple Support Toll Free Phone (24x7 English only): 800-933-480 Apple Sales Email: apple@promise.
VTrak E-Class Product Manual Limited Warranty PROMISE Technology, Inc. (“PROMISE”) warrants that this product, from the time of the delivery of the product to the original end user: a) all components, except the cache backup battery, for a period of three (3) years; b) the cache backup battery, for a period of one (1) year; c) will conform to PROMISE’s specifications; d) will be free from defects in material and workmanship under normal use and service.
Chapter 9: Support PROMISE DOES NOT WARRANT that any product is free from errors or that it will interface without problems with your computer system. It is your responsibility to back up or otherwise save important data before installing any product and continue to back up your important data regularly. No other document, statement or representation may be relied on to vary the terms of this limited warranty.
VTrak E-Class Product Manual Returning the Product For Repair If you suspect a product is not working properly, or if you have any questions about your product, contact our Technical Support staff, and be ready to provide the following information: • Product model and serial number (required) • Return shipping address • Daytime phone number • Description of the problem • Copy of the original purchase invoice The technician helps you determine whether the product requires repair.
Chapter 9: Support You are responsible for the cost of insurance and shipment of the product to PROMISE. Note that damage incurred due to improper transport or packaging is not covered under the Limited Warranty. When repairing returned product(s), PROMISE may replace defective parts with new or reconditioned parts, or replace the entire unit with a new or reconditioned unit.
VTrak E-Class Product Manual 444
Appendix A: Useful Information The appendix covers the following topics: • SNMP MIB Files (below) • Adding a Second RAID Controller (page 445) • Installing a Second RAID Controller (page 446) SNMP MIB Files PROMISE supplies two MIB files to integrate the VTrak E830f, E630f, or E330f subsystem into your SNMP system. These files are in the SNMP folder on the Software CD. The MIB files are: • FCMGMT-MIB.mib • raidv4.
VTrak E-Class Product Manual Installing a Second RAID Controller To install a second RAID controller in your VTrak subsystem: 1. Shut down the subsystem. 2. Remove the blank cover from the right RAID controller slot. 3. Carefully slide the new RAID controller into the slot until the handle locks in place. 4. Attach your data and management cables to the new controller, as needed. See the “Making Management and Data Connections” on page 19 for cable connection information. 5.
Installing a Second RAID Controller New Settings for Dual Controllers With the second controller successfully installed, make the following settings: • Redundancy Type – Set to Active-Active or Active-Standby. See “Making Subsystem Settings” on page 77 or page 211. • LUN Affinity – If you choose Active-Active redundancy. See “Making Controller Settings” on page 86 or page 216. Note The VTrak subsystem boots its RAID controllers sequentially.
VTrak E-Class Product Manual 448
Appendix B: Multipathing on Windows The appendix covers the following topics: • Before You Begin (below) • Installing PerfectPath (page 450) • Verifying Installation (page 451) • Running Perfect Path View (page 453) • Monitoring Your LUNs and Paths (page 454) • Features and Settings (page 460) • Troubleshooting (page 467) • Updating PerfectPath (page 468) • Repairing PerfectPath (page 469) • Removing PerfectPath (page 470) PerfectPath is a multipathing software designed for use with PROM
VTrak E-Class Product Manual Note If you have a complex configuration, such as multiple HBAs connected with multiple LUNs and paths to your PC, installation can take a long time. You can choose to temporarily disconnect your storage, install PerfectPath, then reconnect your storage to reduce installation time. Installing PerfectPath To install the PerfectPath software: 1. Download the PerfectPath installer file from PROMISE support: http://www.promise.
Verifying Installation Verifying Installation Before you can verify PerfectPath installation: • Your Host PC must have multiple data-path connections to the VTrak subsystem. • The VTrak must be fully booted. • The VTrak must have at least one logical drive. See “Making Management and Data Connections” on page 19 for information about making data connections.
VTrak E-Class Product Manual 4. In the Device Manager window, click Disk drives. 5. Under Disk drives, look for “Promise VTrak Multi-Path Disk Device” in the Disk drives list. See Figure 1. Figure 1.
Running Perfect Path View Running Perfect Path View Running PerfectPath View includes these functions: • Starting PerfectPath View (page 453) • Quitting PerfectPath View (page 453) Starting PerfectPath View To start PerfectPath View: From the Start menu, choose All Programs > PerfectPath > PerfectPath View. The PerfectPath View window opens. See Figure 2. Figure 2.
VTrak E-Class Product Manual Monitoring Your LUNs and Paths Monitoring your LUNs and Paths includes these functions: • Viewing LUN Properties (page 454) • Viewing Path Properties (page 455) • Viewing LUN Performance Statistics (page 456) • Viewing Path Performance Statistics (page 457) • Viewing Events (page 459) • Clearing Path Statistics (page 459) Viewing LUN Properties To view a list of all LUNs: 1. 2. Click a Server in Tree View. Click the Properties tab.
Monitoring Your LUNs and Paths Move the scroll bar or expand the window to see all of the reported information. To view a single LUN and all of its Paths: 1. Click the LUN 2. Click the Properties tab. in Tree View. The Properties tab reports: • LUNs – Name, size, and load balance policy • Paths – Path ID, state, and adapter name Move the scroll bar or expand the window to see all of the reported information.
VTrak E-Class Product Manual See also: • “Load Balance Policy” on page 461 • “Refreshing the Objects” on page 465 Viewing LUN Performance Statistics To view performance statistics for a LUN: 1. 2. Click the LUN in Tree View. Click the Performance tab. The Performance tab reports the state and cumulative counts for each path to that LUN.
Monitoring Your LUNs and Paths Move the scroll bar or expand the window to see all of the reported statistics. The Performance tab reports the following data for each path: • Path ID • Bytes Written • State (Active or not) • Non-IO Requests • Read Requests • Queue Depth • Write Requests • Retries Count • Bytes Read • Failure Count An Active state indicates this path is available to handle I/O requests. If Active does not appear, the path is designated as Standby.
VTrak E-Class Product Manual The Performance tab reports the state and cumulative counts for a specific path. Move the scroll bar or expand the window to see all of the reported statistics. The Performance tab reports the following data for each path: • Path ID • Bytes Written • State (Active or not) • Non-IO Requests • Read Requests • Queue Depth • Write Requests • Retries Count • Bytes Read • Failure Count An Active state indicates this path is available to handle I/O requests.
Monitoring Your LUNs and Paths Viewing Events Click the Events tab to view MPIO related events. The data includes: • Type – Error, Warning, or Information • Server • Time • Message • Date Move the scroll bar or expand the window to see all of the reported information. Use this information to verify that settings changes took place and diagnose problems.
VTrak E-Class Product Manual Features and Settings Features and Settings include the following functions: • Automatic Load Balancing for Failover Policy (page 460) • Load Balance Policy (page 461) • Path Verification (page 462) • PDO Removal (page 463) • Performance Tab Refresh Rate (page 464) • Round Robin Count (page 464) • Refreshing the Objects (page 465) • Viewing System Information (page 465) • Saving System Information (page 466) Automatic Load Balancing for Failover Policy The PRO
Features and Settings Load Balance Policy Load Balance Policy is a method of equalizing the I/O traffic over each path by systematically dividing the load among multiple paths. • Failover Policy – No load balancing. With Automatic Load Balancing disabled, the first path discovered is the primary path. I/Os follow the active path until it fails, then they change to next available path. Each LUN uses only one active path. See “Automatic Load Balancing for Failover Policy” on page 460.
VTrak E-Class Product Manual 3. Click the Next button. The Path Selection tab displays. 4. Take the action appropriate for your policy selection. • For Round Robin and Least Queue Depth, no action is required. Skip to step 5. • For Failover, move the path you want to be active to the Primary Path Selected pane. Move all other paths to the Path Available pane. • For Round Robin with Subset, move the paths you want to be active to the Primary Path Selected pane.
Features and Settings 3. Click the arrows or type a new value in the Path Verification Period field to change the interval. 30 seconds is the default value. 4. 5. Click the Apply button. Click the OK button in the confirmation box. The new setting takes effect immediately.
VTrak E-Class Product Manual Performance Tab Refresh Rate Refresh Rate refers to the number of seconds between refreshes of the data reported on the Performance tab. Changing Refresh Rate Settings To change the refresh rate on the Performance tab: 1. Do one of the following actions: • Click the Advanced Settings icon. • From the Operations menu, choose Advanced Settings. The Advanced Settings dialog box appears with the MPIO Parameters tab displayed. 2. Click the General tab. 3.
Features and Settings 10 I/Os is the default value. 4. Click the Apply button. The new setting takes effect immediately. See also: • “Load Balance Policy” on page 461 • “Viewing LUN Performance Statistics” on page 456 • “Viewing Path Performance Statistics” on page 457 Refreshing the Objects Use this function after making an addition or deletion to your LUNs or paths. To refresh the objects, do one of the following actions: • From the Operations menu, choose Refresh. • Click the Refresh icon.
VTrak E-Class Product Manual System information supplies information about the Host PC or Server, including: • Host Name • MPIO Version • Operating System • MPDEV File • OS Version • MPDEV Version • OS Manufacturer • MPSPFLTR File • IP Address • MPSPFLTR Version • Storport File • DSM File • Storport Version • DSM Version • MPIO File Note File information includes the file name and location of the installed file in the server’s file system.
Troubleshooting Troubleshooting If you see no LUNs in the PerfectPath GUI, or no Multi-Path Disk Devices under Disk drives (see Figure 3), do the following actions: • Verify that there is at least one logical drive on the VTrak • Check your HBA cards and driver installation • Check your data connections Make any needed corrections and reboot your Host PC as needed. Figure 3.
VTrak E-Class Product Manual Updating PerfectPath To update your PerfectPath software to the latest version: 1. 2. Download the new PerfectPath installation file from PROMISE support: http://www.promise.com/support/ and save the installation file to your Windows desktop. Manually remove the current PerfectPath installation. See “Removing PerfectPath” on page 470. 3. Install the new PerfectPath software. See “Installing PerfectPath” on page 450.
Repairing PerfectPath Repairing PerfectPath To implement this procedure, you must use the same PerfectPath.exe installer file that you used to install the PerfectPath software onto your PC. The installer’s version number is part of its file name. However, there is no corresponding number in the PerfectPath software. To repair the PerfectPath software: 1. Double-click the PerfectPath.exe file to start the installer. 2. In the Welcome screen, click the Next button. 3.
VTrak E-Class Product Manual Removing PerfectPath Preferred Method This procedure uses the uninstaller included with PerfectPath. To remove the PerfectPath software: 1. From the Start menu, choose All Programs > PerfectPath > Uninstall PerfectPath. 2. In the Welcome screen, click the Next button. 3. In the Program Maintenance screen, choose the Remove option, then click the Next button. 4. In the Remove the Program screen, click the Remove button. 5.
Appendix C: Multipathing on Linux The appendix covers the following topics: • Before You Begin (below) • Task 1: Meeting Package Requirements (page 473) • Task 2: Preparing the Configuration File (page 476) • Task 3: Making Initial Host Settings (page 478) • Task 4: Create and Configure Devices (page 480) • Task 5: Setting-up ALUA (page 481) • RPM Packages and Documents for Linux MPIO (page 486) • Linux MPIO: Known Issues (page 488) • Sample multipath.
VTrak E-Class Product Manual Check Initial Setup To check your initial setup, verify that you can view the logical drives on your VTrak from your Linux desktop or terminal window. Refer to the Linux Administration Manual for the procedure on your system. • If you can see your logical drives, the system is properly configured. Go to “Task 1: Meeting Package Requirements” on page 473. • If you cannot see your logical drives, make the necessary adjustments and check again.
Task 1: Meeting Package Requirements Task 1: Meeting Package Requirements The latest device mapper and multipath packages must be loaded onto your Linux host before configuring Device Mapper Multipath (DM-MP). When this document was written, the current versions were: • • • • • • • For RHEL 5.3 • device-mapper-1.02.28-2.el5 • device-mapper-multipath-0.4.7-23.el5 For RHEL 5.4 • device-mapper-1.02.32-1.el5 • device-mapper-multipath-0.4.7-30.el5 For RHEL 5.5 • device-mapper-1.02.39-1.
VTrak E-Class Product Manual 2. Type the following command and press Enter: # rpm -ivh device-mapper-multipath-0.4.7-8.el5.i386.rpm The system returns the following lines: Preparing... ##################### [100%] 1:device-mapper-multipath##################### [100%] # (or a similar message) Important Where possible, obtain the device mapper and multipath tool from the original installation CDs to ensure full compatibility with your existing OS. Refer to your OS documentation for more information.
Task 1: Meeting Package Requirements 2. Type the following command and press Enter: # rpm -qa | grep device-mapper If the required package is present, the system returns the following line. SLES 10 SP2: device-mapper-1.02.13-6.14 SLES 10 SP3: device-mapper-1.02.13-6.14 SLES 11: device-mapper-1.02.27-8.6 SLES 11 SP1: device-mapper-1.02.27-8.17.20 Note that the actual version number might be different, depending on your configuration. 3.
VTrak E-Class Product Manual Task 2: Preparing the Configuration File To setup multipathing with VTrak, or any other subsystem, you must provide the required device attributes in a configuration file. The multipath configuration file is named multipath.conf. The functional version of the file is saved in the /etc directory. RedHat Systems For RedHat systems, there is a default /etc/multipath.conf file. However, the default file does not have the required device attributes to work with VTrak.
Task 2: Preparing the Configuration File 4. Edit the file to include the following lines under devices: devices { device { vendor product path_grouping_policy "Promise" "VTrak" multibus getuid_callout path_checker path_selector hardware_handler failback rr_weight rr_min_io no_path_retry features product_blacklist } "/sbin/scsi_id -g -u -s /block/%n" readsector0 "round-robin 0" "0" immediate uniform 100 20 "1 queue_if_no_path" "VTrak V-LUN" } 5.
VTrak E-Class Product Manual Task 3: Making Initial Host Settings After the packages and configuration file are installed, the Host is ready to accept multipath settings. Setting the Daemon to Run RHEL 5.3, 5.4, 5.5 This action requires RHEL installation with the “linux mpath” Option. See “Before You Begin” on page 471. To set the MP daemon to run at boot time: 1. Open a terminal window. 2. Verify that /etc/rc.d/rc[3~5].d/ has a symbolic link to /etc/rc.d/init.d/multipathd. Also see the Note below.
Task 3: Making Initial Host Settings If the module is loaded, the system returns: dm_multipath 215770 (or a similar message) 3. Verify that the device mapper module is loaded. # lsmod | grep dm_mod If the module is loaded, the system returns: dm_mod 56537 8 dm_snapshot... (or a similar message) Verifying the Daemon is Running To verify that the MP daemon is running: 1. Open a terminal window. 2. Check the daemon’s status. 3. Do one of the following actions: # /etc/init.
VTrak E-Class Product Manual Task 4: Create and Configure Devices This step applies the settings from the multipath.config file to the Host. 1. Open a terminal window. 2. Type the following command and press Enter: #multipath -v3 The system returns: ... ==== paths list ==== uuid hcil dev dev_t pri dm_st chk_st vend... 222490001555459b3b 2:0:0:0 sdb 8:16 1 [undef][undef] Prom... 222b40000155a75b49 2:0:0:2 sbc 8:32 1 [undef][undef] Prom... 20efcff5501000121a 3:0:0:0 sbd 8:48 1 [undef][undef] Prom...
Task 5: Setting-up ALUA Task 5: Setting-up ALUA VTrak supports Asymmetric Logical Unit Access (ALUA) on the latest Linux distributions: • RedHat Linux RHEL 5.4 • RedHat Linux RHEL 5.5 • SuSE Linux SLES 10 SP3 • SuSE Linux SLES 11 • SuSE Linux SLES 11 SP1 PROMISE provides RPM packages and multipath.conf files for ALUA. See “RPM Packages and Documents for Linux MPIO” on page 486. RedHat Linux RHEL 5.4 Default Kernel To support ALUA within RHEL 5.
VTrak E-Class Product Manual 3. Install this patched alua_dh_scsi source module. 4. Make your own rpm. rpm -ivh scsi_dh_alua_VTrak-1-1.src.rpm cd /usr/src/redhat/SPEC rpmbuild -ba scsi_dh_alau.spec 5. Determine your system architecture, x86_64 or i386. uname -a 6. Install the appropriate scsi_dh_alua driver module. • i386 cd /usr/src/redhat/RPM/i386 rpm -ivh scsi_dh_alua_VTrak-1-1.i386.rpm • x86_64 cd /usr/src/redhat/RPM/x86_64 rpm -ivh scsi_dh_alua_VTrak-1-1.x86_64.rpm 7.
Task 5: Setting-up ALUA Kernel with XEN or PAE support To support ALUA within RHEL 5.5 using kernel with XEN or PAE support: 1. Install RHEL 5.5. When the CD is chosen for installation, immediately type linux mpath. 2. Copy the PROMISE-supplied multipath.conf file to the /etc directory. 3. Install this patched alua_dh_scsi driver module. 4. Make your own rpm. cp multipath.conf.alua-rhel5.5 /etc/multipath.conf rpm -ivh scsi_dh_alua_VTrak-2-1.src.rpm cd /usr/src/redhat/SPEC rpmbuild -ba scsi_dh_alau.
VTrak E-Class Product Manual • Force install the appropriate new multipath-tool RPM package. i586 #> rpm -ivh -force multipath-tools-0.4.7-34.50.10.ass.fix.i586.rpm x86_64 #> rpm -ivh -force multipath-tools-0.4.7-34.50.10.ass.fix.x86_64.rpm 3. Copy the PROMISE-supplied multipath.conf file to the /etc directory. #> cp multipath.conf-vtrak-alua-sles10-sp3 /etc multipath.conf 4. Check the multipath configuration.
Task 5: Setting-up ALUA SuSE Linux SLES 11 SP1 Not updated with Novell SP1 patches If you did NOT update with Novell SLES 11 SP1 patches: 1. Determine your system architecture, i586 or x86_64. 2. Install the appropriate patched scsi_dh_alua.ko device handler. #> uname -a • i586 #> rpm -ivh --force scsi_dh_alua_sles11sp1-2-1.i586.rpm • x86_64 #> rpm -ivh --force scsi_dh_alua_sles11sp1-2-1.x86_64.rpm 3. Copy the PROMISE-supplied multipath.conf file to the /etc directory. #> cp multipath.conf.
VTrak E-Class Product Manual RPM Packages and Documents for Linux MPIO PROMISE provides RPM packages and multipath.conf files for Linux on the support: http://www.promise.com/support/.
RPM Packages and Documents for Linux MPIO Package Folder SLES11-SP1 packages scsi_dh_alua_sles11sp1-2-1.i586.rpm scsi_dh_alua_sles11sp1-2-1.x86_64.rpm scsi_dh_alua_sles11sp1-2-1.src.rpm ALUA multipath.conf.alua-sles11sp1 How to Configure MPIO SLES 11sp1.doc normal multipath.conf-vtrak-normal-sles11sp1 How to Configure MPIO SLES 11sp1.doc RHEL-5.3 normal multipath.conf-vtrak-normal-rhel5-3 RHEL-5.4 package scsi_dh_alua_Vtrak-1-1.i386.rpm scsi_dh_alua_Vtrak-1-1.x86_64.
VTrak E-Class Product Manual Linux MPIO: Known Issues Issue OS Description 1 SLES 11 GMC OS multipath with SAS interface makes kernel panic. 2 SLES 11 GMC OS sets default rports dev_loss_tmo value at 10 seconds resulting in loss of the path during failover/failback. 3 RHEL 5.4 With FC switch, HBA driver (such as Emulex 4g, QLogic 8g) sets rports dev_loss_tmo value too small, resulting in loss of the path during failover/failback. To fix this problem, increase the value to 60 seconds.
Sample multipath.conf File Sample multipath.conf File Below is a complete multipath.conf file for VTrak. • If you have no other multipath devices on your Host, you can use this multipath.conf file as shown. • If you have other multipath devices, add these settings to your existing multipath.conf file.
VTrak E-Class Product Manual 490
Appendix D: VTrak Monitor The appendix covers the following topics: • Downloading and Installing VTrak Monitor (below) • Using VTrak Monitor (below) • Monitoring Subsystems (page 495) • Diagnosing a Subsystem (page 496) • Viewing Information (page 497) • Managing the VTrak with WebPAM PROe (page 499) • Troubleshooting (page 499) Downloading and Installing VTrak Monitor VTrak Monitor is a free application available from the App Store.
VTrak E-Class Product Manual With Bonjour Discovery To use Bonjour discovery, the subsystem must be on the current Wi-Fi network. See “Choosing a Wi-Fi Network” on page 495. To add a VTrak subsystem using Bonjour: 1. Tap the + button at the top right corner of the screen (right). 2. Tap the Search Device icon in the dropdown menu. The Bonjour dialog box displays a list of available subsystems, identified by model and IPv6 address. See Figure 1. Figure 1.
Using VTrak Monitor Figure 2. Home screen Status icon Subsystem: • IP address • Up time • Model and type Tap anywhere in the box to display the Summary screen. The Status , , or icon indicates that the subsystem is connected. For more information on these icons, see “Top-Level Monitoring” on page 495 and “Troubleshooting” on page 499. Viewing a VTrak Subsystem To view a VTrak subsystem from the Home screen, tap the VTrak subsystem. See above, Figure 2. The Summary screen appears. See Figure 3.
VTrak E-Class Product Manual Deleting a VTrak Subsystem One at a Time To delete one subsystem from VTrak Monitor: 1. Click the Home icon to go to the Home screen. 2. To expose the Delete button, touch and drag the right edge of the VTrak box to the left. Figure 4. Delete button Delete button 3. Tap the Delete button. The subsystem is deleted from VTrak Monitor. All Subsystems at Once To delete all subsystems from VTrak Monitor: 1. Click the Home 2.
Monitoring Subsystems Choosing a Wi-Fi Network Bonjour discovery only works on the currently chosen Wi-Fi network. See “With Bonjour Discovery” on page 492. To choose a Wi-Fi network: 1. Press iPad or iPhone’s Home button to go to desktop. 2. Tap the Settings icon. 3. In the Settings list, tap Wi-Fi. 4. Under Choose a Network..., tap the network you want use. 5. Press the Home button again to return to the desktop. See your iPad or iPhone User Guide for more information.
VTrak E-Class Product Manual Additional Actions • To view a list of a each type of component, tap the corresponding component icon at the top of the screen. • To view more information about a single component, tap the component in the list. • To locate the component in the VTrak subsystem, tap the Locate button beside that component. The LEDs for that component blink for one minute. See pages 377 through 379. Diagnosing a Subsystem To diagnose a problem on a VTrak subsystem: 1.
Viewing Information Viewing Information Devices To view device information: 1. 2. 3.
VTrak E-Class Product Manual Event Severity Levels Level Description Critical Action is needed now and the implications of the condition are serious. Major Action is needed now. Warning User can decide whether or not action is required. Information Information only, no action is required. Notes • The default setting displays only Major or Critical events. To view Information and Warning events, see “Changing VTrak Monitor Settings” on page 494.
Managing the VTrak with WebPAM PROe Managing the VTrak with WebPAM PROe To launch WebPAM PROe through your iPad or iPhone, go to the Summary screen and tap the Manage icon. For more information, see “Chapter 4: Management with WebPAM PROe” on page 69. When you are done using the WebPAM PROe, tap the Done button in the top left corner of the screen. You return to the Summary screen.
VTrak E-Class Product Manual 500
Index A C about this manual 1 adaptive writeback cache explained 363 setting 87, 217 alarm patterns 375 alias controller 86, 216 disk array 157, 234 logical drive 166, 245 physical drive 144, 227 Auto Fix 168, 246 auto rebuild, enable 120, 273 cable Ethernet 27–37 Fibre Channel 26–31, 407 iSCSI data 35–37, 366, 368 power 41 RJ11-to-DB9 15, 40, 206 SAS expansion 30, 39 serial 15, 40, 206, 405 UPS control 40 cache adaptive writeback 363 forced read ahead 363 read 362 reported events 411 settings 86, 216 wr
VTrak E-Class Product Manual D CLU enter 208 exit 210 online help 209 problem reporting 382 Quick Setup 55 serial connection 44, 206 SSH connection 207 Telnet connection 207 Command Line Interface, see CLI Command Line Utility, see CLU configuration script export 82 import 82 connection problems browser 408 Fibre Channel 406 management port 406 SAS 407 serial connection 405 connection, power 41 controller alias 86, 216 dual controllers and SATA drive 447 heartbeat LED 41, 377 information 85, 215 locate 88
Index E Fibre Channel, cont.
VTrak E-Class Product Manual host interface, reported events 416 host support browsers 10 operating systems 8 iSCSI, cont.
Index iSCSI, cont.
VTrak E-Class Product Manual N LUN map change map type 183, 282 delete 182, 281 edit 182, 281 list 180, 279 map LUN to initiator 181, 182, Netsend recipients 301 requirements 301 service 301 settings 132, 301 NIC, iSCSI 35, 37 node, Fibre Channel 184, 252 NTP settings 213 synchronizing 214 NVRAM event log 136, 276, 382 280 map LUN to port 181, 182, 280 map LUN to target 181, 182, 280 LUN masking & mapping, enable 183, 277 O M online capacity expansion defined 347 reported events 419, 420 online
Index physical drive alias 227 capacity coercion 87 configuration status 226 DMA mode 225 force offline 146, 227 global settings 225 information 141, 226 list 225 locate 228 medium error threshold 225 operational status 226 reported events 420–422 settings 227 stale and PFA condition 227 statistics 226 physical ports, default IP addresses power connection 41 LED 41, 377 power cycle the subsystem 409 power management, enable 157, 235 power saving 87, 217, 364 power supply locate 219, 221 replace 323 repor
VTrak E-Class Product Manual recondition a battery 90, 123, 223 Redundancy Check 246 logical drive 168 reported events 424–425 settings 118 releasing lock 78, 212 renewing lock 77, 212 replace battery 324 controller 326, 327 power supply 323 reported events 410–427 battery 411 BBU 411 blade server 411 cache 411 controller 412–414 CRC 414 disk array 414 drive interface 414–415 enclosure 415 event log 415 Fibre Channel 415 firmware update 416 host interface 416 initiator 417 JBOD 418 logical drive 418–419 Me
Index serial connection cable 40 problems 405 setting up 44, 206 UPS 40 service report, save 79 sessions, iSCSI delete 200, 266 information 199, 267 list 198, 266 settings 200, 266 setting the lock 77, 212 settings background activities 114, 273 buzzer 91, 313 cache 86, 216, 363 capacity coercion 216 CIM 131, 299 controller 86, 216 disk array 157, 233 email 124, 295 enclosure 93, 220 Fibre Channel port 185 Fibre Channel ports 253 initialization 119, 274 iSCSI global 189, 258 LDAP 291 logical drive 166, 245
VTrak E-Class Product Manual spare drive, cont.
Index trunks, iSCSI add 197, 271 delete 198, 272 list 197, 270 settings 198, 271 VTrak Monitor add subsystem 491 delete subsystem 494 device information 497 diagnosing a subsystem 496 download 491 install 491 launch 491 logging into a subsystem 493 monitoring 495 problem reporting 495 runtime events 497 settings 494 support information 498 U unknown, reported event 427 UPS control connection 40 information 98, 285 list of units 96, 283 settings 97, 284 USB Support firmware update 319 problem reporting 39
VTrak E-Class Product Manual 512