V20230703 Instruction Manual OHCF03-WT Read Carefully Before Installation Keep for Future Reference
CONTENTS Introduction......................................................................................................... 1 Package List........................................................................................................ 2 Safety Information .............................................................................................. 3 Preparation.......................................................................................................... 4 Initial Installation .......
Package List Mounting Bracket 5" Downrod Receiver 2 1 TH Light Plate IS SI DE F/R 6 3 4 5 1H 2H 4H 8H UP Fan Blades (×3) Canopy Cover LED Light Kit Fan Motor Assembly Canopy Shade Remote Control Coupling Cover Mounting Screws (×4) Spring Washers (×4) Metal Washers (×4) Wire Nuts (×4) Mounting Bolts (×2) Star Washers (×2) Blade Bolts (×13) Balance Kit 2
Safety Information Warning! 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with national and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. This fan is suitable for use with solid-state speed controls. 4. To reduce the risk of personal injury, use only the fasteners provided with the junction box for mounting to the junction box.
Preparation 1. Turn off Your Power Begin installation by removing fuses or turning off circuit breakers to the wiring you will be using. Use your compatible UL listed junction box if you already have one installed. Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Choose Your Mounting Position If you need to install a new UL listed junction box, secure it directly to your building's structure using appropriate fasteners and materials.
Initial Installation Ceiling Concrete Ceiling Anchor Bolt Washer Spring gasket Star Washers Mounting Bracket Mounting Bolts Mounting Screw Supply Wires 1. Pass the supply wires through the central hole of the mounting bracket. 2. Secure the bracket to the junction box with appropriate fasteners. For wood or other thinner and weaker ceilings, use the mounting screws and metal or spring washers or use the mounting bolts and star washers, adding plastic anchors (not included) if necessary.
Downrod Mounting Down rod Clip Down rod Down rod Canopy Pin Canopy Canopy Cover Canopy Cover Coupling Cover Coupling Cover Set Screw Retaining Clip Locking Pin 1. Select either the 5″ or 10″ downrod to match the height of your ceiling. To use the 10″ downrod, remove the Phillips bolts from the mount of the 5″ downrod and disconnect the mount from the downrod. Fit the mount onto the 10″ downrod and secure it using the removed bolts. 2. Remove the pin and clip from the downrod.
Circuit Connections Confirm again that the power has been cut before working with the wiring. Use the wire nuts provided with your fan. Ensure there are no loose wires or connections and secure connectors with electrical tape. Junction Box Black (Live) White (Neutral) Green or Bare Copper (Ground) Black ("AC IN L") White ("AC IN N") Receiver 1. Connect the 5 colored wires of the receiver to the 5 identically colored wires of the fan motor assembly. Secure each set with the attached plugs and sockets.
Canopy Installation Junction Box Mounting Bracket Receiver Canopy Canopy Cover 1. Insert the receiver into the tray of the mounting bracket, allowing it to face the ceiling. For best results, make sure its white antenna remains extended and not tangled with any of the electrical wires. 2. Tuck all the connections neatly into the junction box. 3. Slide the canopy up to the ceiling mounting bracket and place the key hole slots over the mounting screws or bolts on the bracket.
Light Installation 1. Remove the bolts from the bottom of the fan motor assembly. 2. Feed the wire plug of the fan motor assembly through the middle of the light plate. Install the light plate onto the motor and secure it by replacing and tightening the bolts. 3. Connect the LED light kit to the light plate using its magnetic suction-cup bolts. 4. Connect the wire plug of the fan motor assembly to the socket on the LED light kit. 5. Fit the shade onto the light plate, screwing it into place.
Remote Control Operation Install the remote control holder onto any wall or suitable flat surface using two mounting screws/bolts.
Cellphone App Operation Note that the layout of the app interfaces and specific instructions may change as the apps update. Adapt operation to the most recent app version as needed. Smart Life (4.6.2) 1. Confirm your cellphone is connected to a 2.4 GHz Wi-Fi network and its Bluetooth is activated. Confirm that your fan is turned off at its wall switch. Go online or use the QR code below to download the newest version of Smart Life. Set up an account if you have not already done so. 2.
12
7. Click on the fan name, accessing the following control interface.
Amazon Alexa (2.2.501399) 1. Confirm that your cellphone Bluetooth is activated and complete the Smart Life app installation above. Open the Amazon Alexa app on your cellphone and log into your account. 2. In the More submenu, select Add a Device. 3. In the Search interface that opens, find and select “Smart Life”. 4. In the app description that opens, select ENABLE TO USE. 5.
15
Google Home (2.62.115) 1. Confirm that your cellphone Bluetooth is activated and complete the Smart Life app installation above. Confirm both Google Home and Google Assistant are installed on your phone. 2. Open the Google Home app and log into your account. 3. Select Settings on the main interface. 4. In the Home Settings menu that opens, select Add device. 5. In the Set up a device interface that opens, select Works with Google. 6. In the list that opens up, scroll down to “Smart Life” and select it.
17
Troubleshooting Potential Problems Common Solutions Check fuses and/or circuit breakers and reset if needed. Cut off power to the fan and check its internal electrical connections. Fan blades don't rotate Replace the remote control’s batteries. Check that the fan cover is correctly placed and no fasteners interfere with the movement of the blades. Contact customer service to replace a faulty remote control. Check that all fasteners are well tightened.
