- ProMount UA-PRO210 Manual

ManualsBrandsProMounts ManualsTV MountProMount UA-PRO210 UAPRO210

UA-PRO210User’s Manual

5 & 6 mm hex key

1 UA-PRO210 mount (x1)

2 M4, M5 & M6 x 10 bolts (x4)

3 M4, M5 & M6 x 12 bolts (x4)

4 M4, M5 & M6 x 25 bolts (x4)

5 M4, M5 & M6 x 40 bolts (x4)

6 5/16” x 3” lag bolts (x2)

7 Concrete anchors (x2)

8 Ø 10 washers (x2)

9 Square washers

Included Mounting Hardware You Will Need

A Level

B Stud Finder

C Marker

D Drill

E 3/16” or 3/8” drill bit

F Hammer

Supports up to 100 lbs / 45 kg

400 mm VESA

extension (x4)

To reach

400x400 mm

use extensions

Wall Bracket

End Cover

vBar

Cable Cover

Tilt

Cover

Arm

Bracket

Summary of content (5 pages)

PAGE 1
User’s Manual UA-PRO210 Supports up to 100 lbs / 45 kg Included Mounting Hardware 5 & 6 mm hex key 1 2 3 4 5 6 7 8 9 UA-PRO210 mount M4, M5 & M6 x 10 bolts M4, M5 & M6 x 12 bolts M4, M5 & M6 x 25 bolts M4, M5 & M6 x 40 bolts 5/16” x 3” lag bolts Concrete anchors Ø 10 washers Square washers (x1) (x4) (x4) (x4) (x4) (x2) (x2) (x2) You Will Need A Level B Stud Finder C Marker D Drill E 3/16” or 3/8” drill bit F Hammer 400 mm VESA extension (x4) To reach 400x400 mm use extensions Arm Cable Cover Wall
PAGE 2
WARNINGS & CAUTIONS IT IS HIGHLY RECOMMENDED THAT THIS PRODUCT BE INSTALLED BY A PROFESSIONAL. PLEASE REVIEW THIS INSTRUCTION MANUAL COMPLETELY BEFORE STARTING THE INSTALLATION PROCESS. WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you the possibility of damage or destruction of equipment if you do not follow the corresponding instruction.
PAGE 3
INSTALLATION 1 UA-PRO210 Step 1: Separate arm from display bracket: 1.1 Dissassemble tilt mechanism by loosening top bolts (A) and removing lower bolts (B). 1.2 Pull up and away the display bracket from the arm. A B A B Step 2: Mount TV on display bracket: 2.1 Loosen 4 adaptor plate bolts (C) so both VBars (D) can slide. 2.2 Slide Vbars to match mounting holes on TV. 2.3 Insert matching TV bolts (E) and tighten slightly. 2.4 Tighten adaptor plate bolts (D) 2.5 Re-assemble tilt mechanism.
PAGE 4
INSTALLATION (2) UA-PRO210 Step 3: a) Mounting to a wood stud: 3.0a Locate the wood stud. 3.1a Place the mount to a suitable location and height. 3.2a Using a bubble level, hold the mount in a level position and mark the holes position. 3.3a Drill 3/16” holes. 3 F b) Mounting to a masonry wall: 3.1b Place the mount to a suitable location and height. 3.2b Using a bubble level, hold the mount in a level position and mark the holes position. 3.
PAGE 5
INSTALLATION (3) UA-PRO210 Step 5: 5 I A B Cable Management: 5.1 To install the cable, first you need to remove the end cover (I) and slide the cable cover (J) out from the arm. 5.2 Do the same for the rest of the cable covers before installing the cables. 5.3 Install the cables and slide the covers back to the arm. 5.4 Install the end covers. J 6 A H B Step 6: Adjusting the Display: 6.1 Slight loosen Bolt (A); do not loosen fully or remove it, otherwise injury may occur. 6.