Use and Care Manual

IMPORTANT! For safety reasons, the concrete wall must be
capable of supporting the combined weight of the mount
and the display. The manufacturer takes no responsibility for
failure caused by walls of insucient strength.
1
2
3
4
INSTRUCTION MANUAL
Display Size: 17” - 44”
Maximum Load: 20 kg (44 lbs)
Mounting Pattern: 75 mm x 75 mm, 100 mm x 100 mm, 200
mm x 100 mm, 200 mm x 200 mm
Tilt Range: 5° up to 15° down
Pan/Swivel Range: up to 180°
Profile: 5.1 cm - 35.8 cm (2.0” - 14.1”)
(A) Drywall Screw (x2)
(B) Washer (x2)
(C) Concrete Anchor (x2)
(D) M4 x 15 Screw (x4)
(E) M5 x 15 Screw (x4)
(F) M5 Washer (x4)
(G) M6 x 15 Screw (x4)
(H) M8 x 15 Screw (x4)
(I) M8 x 30 Screw (x4)
(J) M8 Washer (x4)
(K) Spacer (x4)
(L) Socket Wrench(x1)
(M) M6 x 12 Screw (x4)
(N) M6 Lock Nut (x4)
IMPORTANT! For safety reasons, this mount must be secured
to a wood stud capable of supporting the combined weight of
the mount and display. Do not mount to drywall alone.
1
Place the mount against the wall over the marked stud. Make
sure it is level and right side up.
Mark two locations (one top and one bottom) at the center of
the stud for securing the mount to the wall (see Fig. 2) and set
it aside.
Drill a 3 mm (1/8”) pilot hole at each marked location.
Place the mount back against the wall and attach it using the
drywall screws (A) and two of the washers (B) provided (see
Fig. 3). Do not over-tighten these screws. Ensure that the
mount remains level after both screws are secured.
2
3
4
5
Part 1A – Mounting to the Wall (Drywall)
Part 1A – Mounting to the Wall (Drywall)
(continued)
SPECIFICATIONS
BOX CONTENTS
HARDWARE KIT
TOOLS REQUIRED
INSTALLATION
PREPARATION
Fig. 4
Read these instructions before you begin. If you are
unsure of any part of the process, contact a professional
contractor or installer for assistance. Improper installation
can result in injury or damage.
The wall or mounting surface must be capable of
supporting the combined weight of the mount and the
display; if not, the structure must be reinforced.
Locate pipes, wires, or any other hazards in the wall where
you wish to install the mount before drilling.
Safety gear and proper tools must be used. Failure to do so
can result in injury or damage.
Two people are recommended for installation. Do not
attempt to lift a heavy display without assistance.
Follow all instructions and recommendations regarding
adequate ventilation and suitable locations for mounting
your display. Consult the owner‘s manual for your particular
display for more information.
CAUTION: This wall mount is intended for use only with the
maximum weight of 20 kg (44 lbs). Use with heavier than
the maximum weights indicated may result in instability
causing possible injury.
1
2
3
4
5
6
WARNINGS
Phillips Head Screw Driver
Electric or Portable Drill
3 mm (1/8”) Drill Bit and Stud Finder for Drywall Installa-
tion
8 mm (5/16”) Masonry Bit for Concrete Installation
Mount (x1)
Adaptor (x4)
Plastic Cover (x2)
Instruction Manual (x1)
Hardware Kit (x1)
Part 1B – Mounting to the Wall (Concrete)
Place the mount against the wall in
the desired location. Make sure it is
level and right side up.
Mark two locations (one top and
one bottom) for securing the
mount to the wall (see Fig. 4) and
set it aside.
Drill an 8 mm (5/16”) hole at each
marked location. Remove any excess dust from the holes.
Insert a concrete anchor (C) into each hole so that it is ush
with the concrete surface (see Fig.5). A hammer can be used
to lightly tap the anchors into place if necessary.
Use a high quality stud nder to locate a stud where you
wish to install your mount. Mark both edges of the stud to
help identify the exact center.
NOTE: You must use the center of the stud to avoid cracking
or splitting the wood during installation.
Prepare the mount for installation
by disassembling the display plate
from the mount. Do this by
removing the safety screws as
shown (see Fig.1). Place the screws
in a safe location.
FULL MOTION WALL MOUNT
FOR LCD, PLASMA, and LED DISPLAYS
Fig. 2
Fig. 3
Fig. 1