NOTE- PLEASE READ THIS DRAWER RE-INSTALLATION DETAIL! ARING H THE BE MOVE (ONE IN EAC RACES) FORWARD SLIDE BEFORE YOU RE-INSERT THE DRAWER, MOVE BOTH BEARING RACES (THE METAL PLATES WITH METAL BALL BEARINGS IN THEM) FORWARD TOWARD THE FRONT OF THE PEDESTAL AS SHOWN R05143 09/01/09 THIS IS WRONGTHE RACE IS NOT ALL THE WAY FORWARD.
ASSEMBLY INSTRUCTIONS Follow Ped to top only - Not Valid for Modesty Panel Remove the drawers from both pedestals. Pull each drawer out fully, and move the slide trigger on each slide up or down to disengage the inner slide. Then slide drawer completely out. Trigger on slide Use furthest slot back on the outside. Lay the worksurface, bottom-side-up, on a smooth surface. A carpet is best, but if none are available, use the carton the top came in. Be sure to remove all staples from the carton before using.
This shows how to attach a return to the RIGHT side of a desk. Reverse for the LEFT side. Attach the RETURN BRACE- RH (shown) to the LEG and TOP, using (2) BLACK SCREWS and (1) SILVER SCREW. Attach the CONNECTOR PLATE to the TOP using (2) SILVER SCREWS, as shown. CONNECTOR PLATE SILVER SCREWS BLACK SCREWS RETURN BRACE- RH Attach the assembled Return to the Desk, as shownusing (2) BLACK SCREWS, (2) SILVER SCREWS, and (1) MACHINE SCREW.
ASSEMBLY INSTRUCTIONSRETURN Before assembly, make sure that you have everything you need- check your parts against the parts list on the last page. If you are missing anything, please call us at 1-800-621-8846. SHOULDER SCREW A Place the TOP on a smooth flat surface, face down. Make sure nothing is underneath to scratch the top! A carpet is best, but you can also use the carton that the desk came in.
NOTE: When assembling the returns to the Corner Desk, remove and discard the adapters that come with the returns. The adapters are only used to fasten a return to a regular desk. Use the SILVER SCREWS to fasten the steel parts into the drilled holes in the top. Use MACHINE SCREWS to fasten the steel parts into the threaded inserts in the top. Use BLACK SCREWS to fasten the steel parts to each other.
ASSEMLY INSTRUCTIONSCORNER DESK Before assembly, make sure that you have everything you need- check your parts against the parts list on the last page. If you are missing anything, please call us at 1-800-621-8846. SHARED LEG (non-handed) CORNER LEG (with wire cover) BACK PANEL BACK PANEL SHARED LEG (non-handed) SILVER SCREW TOP MACHINE SCREW Place the TOP on a smooth flat surface, face down. Make sure nothing is underneath to screatch the top.
Using (2) SILVER SCREWS and (4) BLACK SCREWS, attach MODESTY PANEL to the assembly. The machine screwsscrew into the ADAPTERS. NOW, tighten all screws.
BRIDGE ASSEMBLY Before assembly, make sure that you have everything you need- check your parts against the parts list on the last page. If you are missing anything, please call us at 1-800-621-8846. END MODEL- 72 X 24 Credenza shown END MODEL72 X 30 Desk shown CONNECTOR PLATE CONNECTOR PLATE (Fasten with (2) SILVER SCREWS) SILVER SCREW BLACK SCREWS SILVER SCREW(2) for each CONNECTOR Assemble the two end models that you want to connect.
OVERSHELF ASSEMBLY Before assembly, make sure that you have everything you need- check your parts against the parts list on the last page. If you are missing anything, please call us at 1-800-621-8846. BLACK SCREW (6 PER SIDE) Find the non-handed SIDES. Lay them on a flat surface. Make sure nothing is underneath to scratch them! A carpet is best, but you can also use the carton that the Overshelf came in.
Lay the BACK into position, with tabs going into slots in shelf. Holes should line upwith holes in top!! Fasten back with (4) BLACK SCREWS. Note the Double-faced Tape on the bottom ends of the SIDES. Double-faced tape Double-faced tape M Wire trough- covered by Wire Guide Remove "Half-moon" to allow wire through trough.
SHORT FLANGE IS TOWARD TOP!! Lay the BACK in position, with small offset over TOP, and large offset over SHELF (See Detail K). Holes should line up!! Fasten back with (8) BLACK SCREWS. BLACK SCREW (8 req'd) Note the Double-faced Tape on the ends of the SIDES. K LONG FLANGE IS TOWARD SHELF!! DETAIL K SCALE 1 : 6 Double Faced Tape Double Faced Tape Turn Overshelf upright, and place on Desk.
Before assembly, make sure that you have everything you needcheck your parts against the parts list at the bottom of the page. If you are missing anything, please call us at 1-800-621-8846. FLIPPER DOOR ASSEMBLY Place the DOOR(s) on to the top of the Overshelf, with the locks facing forward, and the SLIDE HINGES touching the front face of the Overshelf, as shown. Line up the slots in the SLIDE HINGES with the holes in the front of the Overshelf.
Before assembly, make sure that you have everything you need- check your parts against the parts list at the bottom of the page. If you are missing anything, please call us at 1-800-621-8846. TACKBOARD ASSEMBLY Overshelf Flange on Overshelf Remove the TACKBOARD from the metal FRAME. Set the TACKBOARD aside. Align the metal FRAME with the Overshelf as shown. The channel at the top of the FRAME will go over the rear flange of the Overshelf, as shown in the Detail.
ASSEMBLY INSTRUCTIONSTRAINING TABLES Before assembly, make sure that you have everything you need- check your parts against the parts list on the last page. If you are missing anything, please call us at 1-800-621-8846. RIGHT LEG LEFT LEG BLACK SCREWS SIDE FLAP Using (2) BLACK SCREWS, fasten the SIDE FLAP to the RIGHT LEG as shown. Repeat for the LEFT LEG. BLACK SCREWS RIGHT LEG BACK LEFT LEG LONG SCREWS Using (4) LONG SCREWS, attach the LEFT LEG and the RIGHT LEG to the worksurface as shown.
(See Detail) Using (2) SILVER SCREWS (Use 4 on the larger tables), fasten the BACK to the WORKSURFACE. Lock the door, and turn the table upright. Unlock the door. (see below) Install SEPTUM into back, fitting the notches on the SEPTUM over the hooks in the BACK. SEPTUM (INSTALLED) SILVER SCREW SEPTUM (INSTALLED) Turn the table right-side-up. Unlock the door, and open it. Insert the SEPTUM into the BACK, attaching the slots into the stirrups in the BACK.
ASSEMBLY INSTRUCTIONSRETURN RIGHT side Before assembly, make sure that you have everything you need- check your parts against the parts list on the last page. If you are missing anything, please call us at 1-800-621-8846. SHOULDER SCREW SHOULDER SCREWS A Place the TOP on a smooth flat surface, face down. Make sure nothing is underneath to scratch the top! A carpet is best, but you can also use the carton that the desk came in.
Before assembly, make sure that you have everything you need- check your parts against the parts list at the bottom of the page. If you are missing anything, please call us at 1-800-621-8846. TACKBOARD ASSEMBLY Overshelf Flange on Overshelf Remove the TACKBOARD from the metal FRAME. Set the TACKBOARD aside. Align the metal FRAME with the Overshelf as shown. The holes in the flange at the top of the FRAME should align with the holes in the flange of the shelf.
SIDE- LH BACK SIDE- RH TACKBOARD BACK LH SIDE TACKBOARD RH SIDE SIDE FLANGE FITS BETWEEN LEG TUBE AND TABLE. TABLE LEG TUBE STEP 1- LOOSEN SCREWS THAT ATTACH THE TRAINING TABLE LEGS TO THE TRAINING TABLE. SLIDE THE LH AND RH SLIDES BETWEEN THE LEG TUBES AND THE TOPS. DO NOT TIGHTEN SCREWS YET. R05147 06/21/10 STEP 2- ATTACH BACK TO SIDES, USING THE FLAT HEAD SCREWS PROVIDED. MAKE SURE EVERYTHING IS SNUGGED UP. STEP 3-SLIP THE TACKBOARD INTO THE BACK. TIGHTEN THE SCREWS ON THE TRAINING TABLE.
Power Entries Base End Power Entry No receptacles are displaced when using a base end power entry. Plug the end of the “whip” assembly into either a power block or harness jumper attached in a raceway. A certified electrician must attach the other end of the base power entry to the building power. Power Pole – End of Run Make sure a wedge block is attached to the end of the panel run. Attach the raceway cover plate to the bottom of the power pole with hardware provided.
POWER ENTRIES PECC132 PX0108 F09545 SCREW ADAPTER BRACKET KNOCKOUT 1) Remove KNOCKOUT from CORNER COLUMN. 2) Install POWER POLE components as show. PEDR132 710186 KNOCKOUT PX0108 F03727 SCREW F02886 SCREW ADAPTER BRACKET F09545 SCREW 1) Remove KNOCKOUT from DESK LEG. 2) Install POWER POLE components as show. PETR132 710186 ADAPTER BRACKET KNOCKOUT PX0108 F11915 NUT F09545 SCREW 1) Assemble ADAPTER BRACKET to 710186 PLASTIC CHANNEL. 2) Remove KNOCKOUT from TRAINING TABLE LEG.
ASSEMBLY INSTRUCTIONS TRAINING TABLE W/ MODESTY PANEL (PTRxxxxM) STEPS 1) Using (4) LONG SCREWS (No 13), attach LEFT LEG & RIGHT LEG to WORK SURFACE. 2) Using (4) BLACK SCREWS (No 14), (2 per side), attach MODESTY PANEL to the two LEGS. 3 3) Using (2) SILVER SCREWS (No 15), attach MODESTY PANEL to WORK SURFACE. 4 14 15 13 2 1 4) Turn the table right-side-up. 5) Insert (2) GROMMETS (No 7) into the work surface. 7 6) Use the (2) TIE BRACKETS (No 12) provided to gang tables together.
