Motion sensor faucet 1 A A B Single hole installation 1.A.For 1-hole sink.insert the cable flexible pipe and the stem into the bottom of the faucet into the sink’s mounting hole.then attach the faucet on the sink. 1.B.For 3-hole sink.insert deck plate over the cable B 3-hole installation 1 flexible pipe and the stem in the mounting stem. aligning the grooves in the deck plate with the arches on the faucet bottom. and then mount the faucet on the sink.
Motion sensor faucet 1 A A B Single hole installation 1.A.For 1-hole sink.insert the cable flexible pipe and the stem into the bottom of the faucet into the sink’s mounting hole.then attach the faucet on the sink. 1.B.For 3-hole sink.insert deck plate over the cable B 3-hole installation 1 flexible pipe and the stem in the mounting stem. aligning the grooves in the deck plate with the arches on the faucet bottom. and then mount the faucet on the sink.
2 3 2. For 3-hole sink.use the screwdriver to remove the base at the bottom of the faucet.replace with the deck plate.and secure the deck plate to the bottom of the faucet. 3 3. Slide the metal washer first.and then the spanner tighten and mounting nut.finally connect faucet with flexible pipe.
2 3 2. For 3-hole sink.use the screwdriver to remove the base at the bottom of the faucet.replace with the deck plate.and secure the deck plate to the bottom of the faucet. 3 3. Slide the metal washer first.and then the spanner tighten and mounting nut.finally connect faucet with flexible pipe.
4 4. Connect control box outlet with flexible pipe 5. Mount the control box under the sink by a cross screwdriver according to the preferred dimenstion, leaving some room to adjust. 4.
5 5. Mount the control box under the sink by a cross screwdriver according to the preferred dimenstion, leaving some room to adjust.
6 6. Cold water pipe connect to mixer valve inlet(mark C). Hot water pipe connect to mixer valve inlet(mark H). 7. Connect the hot & cold supply lines onto the matching water valves and secure the connection with an adjustable wrench. 6. Cold water pipe connect to mixer valve inlet(mark C). Hot water pipe connect to mixer valve inlet(mark H).
7 7. Connect the hot & cold supply lines onto the matching water valves and secure the connection with an adjustable wrench.
8 9 10 8. Connect the data cables and secure them hand tight.
9 9. Remove the battery pack cover and take out 7.1.Connect the data cables and secure them the battery pack; insert 2 AAA batteries. put the battery pack back in the control box and replace the cover firmly. hand tight.
10 10. When install ation steps 1-10 are completed, turn the hot & cold water inlets back on.
11 9. Remove the battery pack cover and take out the battery pack; insert 2 AAA batteries. put the battery pack back in the control box and replace the cover firmly. A When the hand reaches the sensing range. the faucet will come out automatically. Turn off the water automatically after . one minute of continuous discharge. 10. When install ation steps 1-10 are completed, turn the hot & cold water inlets back on. B 11 When the hand leaves the sensing range, the tap automatically turns off the water.
12 12 Set water temperature to desirde setting The water temperature changes by manipulating 13 12 Set water temperature to desirde setting The water temperature changes by manipulating 13 If the water flow rate is lower than normal,there may be build up on the filter washer.Shut off the water valve and remove the mixer valve from the control box.take out the filter washer.clean the filter and reassemble them back.
13 filter 13 If the water flow rate is lower than normal,there may be build up on the filter washer.Shut off the water valve and remove the mixer valve from the control box.take out the filter washer.clean the filter and reassemble them back.
Motion sensor faucet Feature: Notes: -Single -hole or 3-hole installation options -Drip-free Ceramic cartraidge -2.0 gallons per minute Max at 60 psi -Metallic waterway -Infrared sensor functions Model No./Colore/Finishes: - The dirt and impurities in the pipe shall be cleaned before installation. - If the water amount is reduced during use, please take off the filter screen and the bubbler in time for washing and put them back as is.
Motion sensor faucet Feature: Notes: -Single -hole or 3-hole installation options -Drip-free Ceramic cartraidge -2.0 gallons per minute Max at 60 psi -Metallic waterway -Infrared sensor functions - If the water amount is reduced during use, please take off the filter screen and the bubbler in time for washing and put them back as is. Model No./Colore/Finishes: -CP polishde Chrome -BN Brush Nickel PVD -ORB Oil Rubber Bronze - The dirt and impurities in the pipe shall be cleaned before installation.