PRO RUN. GAS Operator's Manual BACKPACK BLOWER MODEL: PBB2417 EEE ROG Before operating, read the instructions. [B73] A IMPORTANT READ CAREFULLY BEFORE USE /\ IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING: To reduce the risk of injury, the user must read and understand the Operator's Manual before using this product. Save these instructions for future reference. Plats no 0 fi.
Table of Content Operation. Maintenance Troubleshooting Specification... Part List and Diagram Warranties... WARNING SYMBOLS AND DEFINITIONS A This is the safety alert symbol. [tis used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death, indicates a hazardous situation which, I not avoided, will result in death or serious injury. Indicates a hazardous situation which, if into avoided, could result in death or serious injury.
Property or Statement Danger of dismemberment! Never use the machine with the grille open, Don't put your hand info the volute or tube: Fuel mixture tank Close the choke Open the choke rx The screw under the "H" stamp is The High-speed mixture adjustment screw. The screw under the "L" stamp is The Low-speed mixture adjustment screw. The screw up the "T" stamp is the idle speed adjustment screw. Press the direction of the Primer Bulb.
IMPORTANT SAFETY INSTRUCTION SAVE THESE INSTRUCTION This manual contains important instructions that should be followed during setup, operation and maintenance of the Blower, Set up Precautions 1.Gasoline fuel and fumes are flammable, and potentially explosive. Use proper fuel storage and handling pa Do not store fuel or other amiable materials nearby. 2.Have multiple ABC class fire extinguishers nearby. perpetration of this equipment may create sparks that can start fires around dry vegetation.
starting engine. Always store gasoline in container approved for flammable liquids. 8.Work Area. Clear the area of children, bystanders, and pets. Ala minimum; Keep ail children, bystanders; and pets outside radius; outside the zone, there is still a risk of injury from thrown objects. Bystanders should be encouraged to wear eye protection. If you are approached, stop the engine. 9. Work from Ladders or on High Surfaces.
mask if operation is dusty. 24. Use Right Appliance Do not use appliance for any job except that for which iris intended. 25.00 Not Force Appliance = It will do the job better and with less likelihood of injury at the rate for which it was designed. 26.00 not Overreach = Keep proper footing and balance at all times. 27:Stay Alert = Watch what you are doing. Use common sense. Do not operate appliance when you are fired.
recurred the equipment on transport vehicles to prevent it from rolling, slipping. and tilting. 7.Industrial applications must follow OSHA requirements. 8.Do not leave the equipment unattended when it is running. Turn off the equipment before leaving the work area. 89.The equipment can produce high noise levels, Prolonged exposure fo noise levels above 85 dBA is hazardous to hearing, Wear ear protection when operating or when working nearby while it is operating.
26 Before use, check for misalignment or binding of moving parts, breakage of parts; and any other condition that may affect the equipment’s operation. If damaged, have the equipment serviced before using. Many accidents are Service Precautions caused by poorly maintained equipment. 27 Use the correct equipment for the application. Do not modify the equipment and do not use the equipment for d purpose for which it is not intended. 1:Before service, maintenance, or cleaning; a.
eld A Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product TO PREVENT SERIOUS INJURY: Operate only with proper spark arrest or installed, Operation of this equipment may create sparks that can start fires around dry vegetation. A spark arrest or may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.
Assembling Blower Tube and Control Handle Insertions the angle tube:into the flexible has fo the end. Angle | 7 Tubs Flexible ~ Hose 2. Turn the lock screw clockwise with the spark plug wrench to tighten the clamp Insert the rear tube into the flexible hose to the end: Rear Tube Flexible Hose 4.
Operation Reed the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Checking before Starting inspect engine and equipment looking for damaged, loose, and missing parts before setup and starting.
Manual Start Prepared std’ iz when the engine is no longer lotto the touch: typically at least 30 minuses after it has last ban run. the engine switch lever at the intermediate position 11 2.Press Primer Button 10 times 1o prim the carburetor 3. Move Choke Knob to the START position: Note: The symbols below are indicated an the {ool near the Choke Knob.
Hot Start To initiate a Hot Start; follow each step of the Cold: Start procedure EXERT Step 5: Stopping the Engine 1.To stop the engine in an emergency. Engine rotate: the engine switch counterclockwise to Switch shut the engine immediately. 2.
WARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL STARTING: Tur the Power Switch of the equipment 16 its “OFF position, wail for the engine to cool, and disconnect the spark plug cap before performing any inspection. maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM EQUIPMENT FAILURE: Do not use damaged equipment.
Check { Filling Fuel AA WARNING! TO PREVENT SERIOUS INJURY FROM FIRE: Fill the fuel tank in a hyperventilated area away from ignition sources: fhe engine ig. hot from use, shut the engine off and Walt for it io cool before adding fusillade not smoke, 1 Clean the Fuel Tank Cap and the area around it. sunscreen and remove the Fuel Tank Cap: Note: Do not use gasoline containing more than 10% ethanol (E10) Do not use E85 ethanol. Add fuel stabilizer to the gasoline or the Warranty is VOID.
Specifications chart: Donor pry against the electrode, the spark plug can be damaged. & Install the new spark plug or the cleaned spark plugging the engine: « Gasket-style: Finger-tighten until the gasket contacts the cylinder had, then fighter about 2-2/3 tam more. Non-gasket style: Finger-tighten until the plug contacts the cylinder head: then tighten about 1/16 mn tiger; NOTICE: Tighten the Spark Plug properly. if loose, the Spark Plug will cause the engine to overheat.
2 FUEL: To protect ihe fuel system ding storage; follow this procedure: a Carefully drain any remaining fuel in tha fuel tank anoint appropriate storage container b.Press the Primer Bulb 710 times, ¢ Dray any residual fuel into stodge container. d Start the Blower. e Allow engine lo run at idle until Blower stalls from blacking fuel. f.RBpldce Ful Cap and tighten. A WARNING] TO PREVENT SERIOUS INJURY FROM FIRE: Drain the Fuel Tanking well-ventilated ares away firm ignition sources.
Troubleshooting Problem Possible Causes Probable Solutions Engine will not start FUEL RELATED: 1: No fuel in tank: 2. Choke notion START position; cold engine. & Gassing with more than 10% ethanol used. (E15 £20, £85, eto 4 Low quality or deteriorated, old gasoline/oil mixture. 5. Carpuretar not primed. 6. Dirty fuel passageways. 7.Carburetor is flooded: 8 Clogged Fuel Filter. FUEL RELATED: 1.Fill fuel tank with fresh 87+ octane stabilization unleaded parasailing mixture only.
Problem Possible Causes Probable Solutions Engine misfires spark plug cap loose. 2. Incorrect spark pliers gap of damaged spark plug, 3: Defective spark plug cap: 4 Cll of low quality gasoline mixture: 5. Incorrect compression. t. Chack cap and wire connections: 2 Re-gap or replace spark plug: 3 Replace spark plug cap. 4: Use only fresh 87+ octane stabilization unleaded gasoline mixture. Do not use gasoline with more than 10% ethanol (E15, E20, E85, etc.) 5.Diagnose and repair compression.
No id ascription GY NO Description Ql FG Rust Hose i 10475 Retaining ring 1 8G Re tin Hiss 1 4051 Soaking Mesh 1 a1 Fuh Tank Cap 1 06 Cramp 1 iv Rubber ake: 4 $07: Bestows Glass 1 BE: Rubber Vale Moat: 1 $081 Telescopic rive.
ETE TE Emissions Control System Warranty Zhejiang Zhejiang Technology Co. Lid, CALIFORNIA'AND FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS Tha US: Environmental Protection Agency (EPA) the California Air Resources Board (CRAB) and Zhejiang Honduran Technology Co. Lid Hereinafter called Zhejiang, ars pleased to explain the Emissions Control System Warranty on your new 2020/2021 small off-road engine.
years: If any such part {including any part that is scheduled only for regular inspection) falls during the period of warranty coverage it will be repaired or replaced at any [BRANDE® Authorized Service Canter at no charge. Any suck part repaired or replaced under warranty will bé warranted forth renaming warranty period.
Evaporation Emissions Fuel Tank Fuel Cap Fuel line Fuel Line Fittings Clamps®™ Pr assure Relief Valves™ Control Valves®s Control Solenoids” Electronic Controls’? (10) (15) (16) (17) 118) Vacuum Control Diaphragms Control Cables: Control Linkages*™ Purge Valves Vapor Hoses Liquidator Separator Carbon Canister Canister Mounting Brackets Carburetor Purge Port Connector Note: As they relate fo the evaporation emission control system.
PRO RUN regularly improves our products, and you may find slight differences between your machine and descriptions contained within this operator's manual. Modifications can be made to the machine without antics and without the obligation to update the manual, providing that the essential safety and functional characteristics remain unaltered: Contact PRO RUN Customer Service with any questions and for:current specifications.
