PRO RUN. GAS Operator's Manual CHAINSAW MODEL: PGS214/PC52140 MODEL: PCS216/RGS2160 Before operating, read the instructions. ZN IMPORTANT READ CAREFULLY BEFORE USE Z\ IMPORTANT SAFETY INSTRUCTIONS ~ SAVE THESE INSTRUCTIONS VEE RTT ET Operator's Manuel before using tis product. Save these instructions for future reference, Please lot us now what you think.
Safety Setup. Operation. AN Table of Content Troubleshooting . Specification Part List and Diagram... Warranties. omen WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards, Obey all safety messages that follow this symbol to avoid possible injury or death. indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Property or Statement Appropriate ear, eye, and head protection must be worn. Always wear safety and gloves when operating the device. Always wear safety and slip-resistant bouts when operating the device. WARNING marking concerning saw chain Orientation. Cutters must face in direction of rotation. The port to refuel the "MIX GASOLINE" Operate the engine switch Flipping the switch to the "0" position, immediately the engine stops, "0" and "1" are shown on switch ¥ button.
IMPORTANT SAFETY INSTRUCTION SAVE THESE INSTRUCTION This manual contains important instructions that should be followed during setup, operation and maintenance of the chainsaw. Set up Precautions 1.Gasoline fuel and furies are flammable, and potentially explosive. Use proper fuel storage and handling procedures. Do not store fuse or other flammable materials nearby. 2 Fave multiple ABC class fire extinguishers nearby. 3.
12.People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to a heart pacemaker could cause pacemaker interference or pacemaker failure, Caution is necessary when near the engine's magneto or recoil starter. 13.Use only accessories that are recommended by manufacturer. Accessories that may be suitable for one piece of equipment may become hazardous when used on another piece of equipment. 14.
application. Do not modify the equipment and do not use the equipment for a purpose for which it is not intended. 29.Never operate a chainsaw when Chainsaw Safety Warnings you are fatigued, il, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 1.Keep all parts of the body away from the saw chain when the chainsaw is operating. Before you start the chainsaw, make sure the saw chain is not contacting anything.
lubricated chain may either break or increase the chance for kickback. 11.Keep handles dry, clean, and free from oil and grease. Greasy, oily handles are slippery causing loss of control, 12, Cut wood only. Do not use chainsaw for purposes not intended. For example: do not ise chainsaw for cutting plastic, masonry or non-wood building materials. Use of the chainsaw for operations different than intended could result in a hazardous situation. 13.
17 People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure, 18. The warnings, precautions, and instructions discussed in this instruct. Page son manual cannot cover all possible conditions and situations that may Our. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Sd A Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product, TO PREVENT SERIOUS INJURY: Operate only with proper spark arrest or installed, Operation of this equipment may create sparks that can start fires around dry vegetation. A spark arrest or may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.
Components and Controls Ha En Ee ENGINE (CHAINSAW SAYS] SAW CHAIN CHAIN GUIDE BAR GUIDE BAR SHEATH SPARK PLUG WRENCH SCREWDRIVER FILE Limit ogo» OPERATOR'S MANUAL Handle Guard / Chain Wraparound Handle Brake Lever Trigger Lockout Switch yd Rear a Handle Gide Bar Baw Chain Starter .
de Bar and Saw Chain Installation and Adjustment WIRY FROM ACCIDENTAL OPERATION: Make sure that the Engine is switched OFF, wait for the Engine fo cool, and unplug the spark Chain's tension often when first using, plug wire before performing any procedure in this section, Mote: New Saw Chains often need to be pensioned several times during first use.
Checking Saw Chain Tension 1.Before using, check the Saw Chain tension. 2.While wearing heavy-duty gloves, use your index finger and thumb to carefully grab the Saw Chain in the middle section under the Chain Guide Bar. 3.Pull the Saw Chain away from the Guide Bar. 4. Ties Saw Chain should sangria back against the Guide Bar. The Chain should fit snugly in the groove of the Chain Guide Bar, yet you should still be able to slide the chain along the Chain Guide Bar by hand. 5.
Biv Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product, Checking Saw Chain Tension inspect engine and equipment locking for damaged, loose, and missing parts before set ap and staring. if any problems are found, do nit use equipment wil fixed properly.
Manual Start A “cold start” fs when the engine is no longer hot to fhe touch, typically at least 30 minutes after it has fast been run. 1.70 start a cold Engine or Test start of the day, ensure the Guide Bar and Saw Chain are not touching or near any object as Chain will spin during startup. Push the Hand Guard { Chain Brake Lever forward to engage the chain brake. Engaged Handle Guard/ Chain Brake Figure 8: Lock the Handle Guard 2.
Pull the Starter Handle rapidly until the Engine starts. Immediately disengage the chain brake by pulling back on the Hand Guard / Chain Brake Lever. Caution! The Saw Chain will immediately start spinning with the Engine running at partial throttle. Allow the Engine to run at partial throttle for § seconds.
Work piece and Work Area Set Up 1.Designate a work area that is clean and well fit. The work area must not allow access by children or pets to prevent distraction and injury. 2. There must not be objects, such as twilit General Operating Instructions lines, nearby that will present a hazard while working. 3.A first-time user should, as a minimum practice, cut logs on a sawhorse or cradle before cutting down trees. 1.
To prevent accidents, place the Hand Guard / the Chain Guide Rar Sheath. Store the too) Chain Brake Lever forward in its engaged indoors out of children’s reach. See Long-Term position after use. Storage on page 25 for complete storage @When the Baw has cooled completely, clean instructions.
the tree may pot fall in desired direction or it may rock back and bind the saw chain, stop culling before the felling back cut is complete and use wedges of wood, plastic or aluminum fo open the cut and drop the tree along the desired line of fall. Wuhan the tea begins to fall remove the chainsaw from the cut, stop the motor, put the chainsaw down, then use thi retreat path planned. Be alert for overhead limbs falling and watch your footing.
d cut over buck (2/3 diameter) to meet Pout (fo avoid pinching} {cut under buck {1/3 diameter} to avoid splintering ANANIAS SN Figure 23: Log Supported One End TT FOSSA SIN INN When the log is supported on both ends, as illustrated in Figure 24 out 1/3 the diameter from the top (overbuy.
procedures.
Cleaning, Maintenance, and Lubrication Note: This maintenance schedule is intended solely as a general guide. If performance decreases or if equipment operates unusually, check systems immediately.
Sharpening/Replacing the Saw Chain CAUTION! Saar heavy-duty work gloves when handling the Saw Chain, 1.For smooth and safe operation, always keep the Saw Chair cutlers sharp. 2 Have the cutlers sharpened by a qualified technician when you notice any of the following symptoms: a. The sawdust becomes powder-kite, b. You can't make the cut without extra farce. ¢. The Chainsaw does nat out straight, d. Vibration increases. 3.
Check | Billing Burl WARNING! TO PREVENT SERIOUS INJURY FROM FIRE: Fill the fuel tank in a well ventilated area away from ignition sources. If the engine is hot from use, shut the engine off and wait for it fo cool before adding fuel. Do not smoke. 1. Clean the Fuel Tank Cap and the area around it. 2. Unscrew and remove the Fug! Tank Cap. Note: Do not use gasoline containing more than 10% ethanol {E10}. Do not use EES ethanol, Add fuel stabilizer to the gasoline or the Warranty is VOID.
+ Gasket style: Finger-tighten until the gasket contacts the cylinder head, then tighten about turn more, » Non-gasket-style. Frightening until the plug contacts the cylinder head, then tighten about 1/16 tum More, ANTIGEN: Tighten the Spark Plug properly. if loose, the Spark Plug will cause the engine to overheat, if over tightened, the threads in the triangle Block will be damaged. 7. Raattach the Spark Plug Cap securely. Alr Filter Maintenance 1.
Warning! TO PREVENT SERIOUS INJURY FROM FIRE: Drain the Fuel Tank Ina well-ventilated area away from ignition sources. If the Engine is hot from use, shut the Engine off and Walt for it 10 cool before draining fuel. Do not smoke. a. Ramove the Fuel Tank Cap and drain any ingraining fuel ino an approved storage container. b.Press the Prime Bulb 10 times. ¢.Drain any residual fuel into the storage container o Start the Engine and run at idle until the Engine stalls from lack of fuel, a.
Troubleshooting Problem Possible Causes Probable Solutions Engine will not start FUEL RELATED: 1.No fuel in tank. 2.Choke not in START position, cold engine. 3. Gasoline with more than 10% ethanol used. (E15, E20, E85, ate.) 4. Low quality or deteriorated, old gasoline mixture. 5. Carburetor not primed. 6. Diy fuel passageways. 7.Carburetor is flooded. FUEL RELATED: 1. Fill fue tank with fresh 87+ octane stabilizer-treated unleaded gasoline mixture only.
Problem Possible Causes Probable Solutions Engine misfires parka plug cap loose. 2. Incorrect spark plug gap or damaged spark plug. 3. Defective spark plug cap. 4.Old or low quality gasoline/oil mixture. 5 Incorrect compression. 4. Chack cep and wire connections. 2. Ru-gap or replace spark plug. 3 Replace spark plug cap. 4. Use only fresh 87+ octane stabilizer-treated unleaded gasoline mixture. Do not use gasoline with more than 10% ethanol (E18, E20, ESS, tsetse. 5.Diagnose and repair compression.
Problem Possible Causes Probable Solutions Engine runs, Chain rotates but does not cut or 1.Saw Chain not pensioned properly. 2. Saw Chain dull. 1. Tension Saw Chain properly, sharpener Saw Chain or replace. 3, Reverse direction of Saw Chain, installed correctly, cuts poorly. 3. Saw Chain installed backwards, Chain comes off |1. Chaln tension too loose. 1.Adjust Saw Chain tension. Guide Bar. 2 Guide Bar and Chair not 2 Review and correct Guide Bar and Chairs installation. Guide Bar and Chain running hot 1.
Parts List and Diagram Part List for Base Until No. |Description Qty No. |Description Qty 1 |Right Cap Assembly 1 40 Shock Absorbed 1 2 |Screw M5x40 1 41 [Dust Hashish 1 3 |Baffle Casing 1 42 Retaining Bracket 1 4 Heavy Hammer Casing 1 43 |Choke Knob + 1 5 |Bezel 1 44 | Starter Assembly 1 6 heavy Hammer 1 45 |Self-Tapping Screw 8T4.
Parts List and Diagram Part List for Base Until No. |Description Qty No. |Description Qty 78 |Fuel Port Cap Assembly 1 97 belfry-Tapping Screw ST4x14 1 80 |Anti-Drop Plate 1 98 Air mistake Gasket 1 81 |O-Type Rubber Seals 24.734x1.8 1 89 Air intake Tube 1 B2 |Fuel Port Cap 1 100 {Carburetor Gasket 1 83 |O-Type Rubber Bela 193.8 1 101 {Pump Tubing (2.
Pat List for Engine No. |Description Oty No.
EET de Emissions Control System Warranty Zhejiang Zhejiang Technology Co., Lid, CALIFORNIA AND FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS This LLS. Environmental Protection Agency (EPA), the California Air Resources Board (CARBS, and Zhejiang Zhejiang Technology Co, Lid { hereinafter called Heilongjiang, are pleased to explain the Emissions Control System Warranty on your new 2020/2021 small off-road engine.
years. H any such part {including any part that is scheduled only for regular inspection) falls during the period of warranty coverage, it will be repaired or replaced at any [BRAND] ® Authorized Service Center at no charge. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period. A statement to the effect of “repair of replace as necessary” would not reduce the period of warranty coverage.
Evaporation Emissions Ful Tank (10 Faust Cap {11} Fuse Line {12} Fuel Line Fittings {13} Clamps™ {14) Pr assure Relief Valves™ {18} Control Vakves™ (18) Control Solenoids™ {17} Electronic Controfs™ {18) Vacuum Control Diaphragms Control Cables Control Linkages™ Purge Valves Vapor Hoses Liquid/vapor Separator Carbon Canister Canister Mounting Brackets Carburetor Purge Port Connector Hole: As they relate to the evaporation emission control slender.
