USER'S GUIDE Remote controls programming
IN THIS GUIDE E2050-ER1 AND RT-U43CO REMOTE CONTROLS MODELS E2050-ER1 AND RT-U43CO BUTTONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 PROGRAMMING THE E2050-ER1 REMOTE CONTROL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PROGRAMMING THE RT-U43CO REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 RC-U49C+ REMOTE CONTROL MODEL RC-U49C+ BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E2050-ER1 AND RT-U43CO REMOTE CONTROLS There are three remote controls for the digital terminals: the E2050-ER1, the RT-U43CO and the RC-U49C+. You can identify your model by examining the "5" key. • This key is oval on the E2050-ER1 and square on the RT-U43CO and RC-U49C+. • The RC-U49C+ is the one with the three buttons "MODE", "ALL" and "AUDIO" at the top.
E2050-ER1 AND RT-U43CO REMOTE CONTROLS (CONTINUED) PROGRAMMING THE E2050-ER1 REMOTE CONTROL This step is not essential, but allows you to use the digital terminal remote control with your TV and VCR. How to Program the TV Mode Key 1. 2. 3. 4. Turn on the TV set. Point the remote control away from the digital terminal, the TV and the VCR. On your remote control, press and hold TV and SELECT at the same time until the LED on the remote blinks twice.
E2050-ER1 AND RT-U43CO REMOTE CONTROLS (CONTINUED) How to Identify Programmed Codes 1. Point the remote control away from the digital terminal , TV and VCR. 2. To identify the TV code, press and hold TV and SELECT at the same time until the LED on the remote blinks twice. or 2. To identify the VCR code, press and hold VCR and SELECT at the same time until the LED on the remote blinks twice. 3. Slowly enter the code 9 9 0; the LED should blink once each time you enter a digit.
E2050-ER1 AND RT-U43CO REMOTE CONTROLS (CONTINUED) How to Program the VCR Mode Key 1. Turn on the VCR or DVD player, then press and hold the VCR and SELECT keys until the LED stays lit. 2. Repeat the steps described under How to Program the TV Mode Key, substituting the VCR key for the TV key. 3. Write the code and your TV brand here: _____________________________ Write the code and your DVD brand here: _____________________________ 4.
E2050-ER1 AND RT-U43CO REMOTE CONTROLS (CONTINUED) How to Program the Volume Control 1. Press and hold the CBL and SELECT keys at the same time until the LED stays lit. 2. Press the VOL+ key, and then the CBL key. The LED will blink twice and go out. 3. To control the volume through the TV again, repeat step 1 and, at step 2, press the VOL+ and TV keys. How to Program the SmartKeys™ You can program the CBL and TV keys so that whenever either is pressed, several tasks take place in sequence.
RC-U49C+ REMOTE CONTROL These three remote controls have different programming procedures for their TV and VCR mode keys, as well as different VOD/VCR keys. It’s therefore important that you follow the instructions for your particular model. MODEL RC-U49C+ BUTTONS Selects device being operated.
RC-U49C+ REMOTE CONTROL (CONTINUED) PROGRAMMING THE RC-U49C+ REMOTE CONTROL Point and Press® Programming This method allows you to program the remote control without using codes. Instead, the remote control automatically finds the correct command that you select in a variety of codes until you find the code that operates your device. You then lock in the correct code as described below.
RC-U49C+ REMOTE CONTROL (CONTINUED) Code Number Readback To identify the 3-digit setup codes stored under the Point and Press® programming method, follow these steps: 1. For the TV code, press and hold the TV and SELECT keys at the same time until the TV button illuminates. 2. Press the INFO key. The TV button will "blink back" the code numbers, with a 1-second interval between each digit of the code. Example: For code "035", the indicator light will blink 10 times, then 3 times, then 5 times.
RC-U49C+ REMOTE CONTROL (CONTINUED) ALL button Once you have programmed each of your devices, press ALL button to turn all of them on/off with a single button press. You can also program the ALL button to tune your TV to its correct output channel (usually 3). Programming the ALL Button 1. Press MODE, then CBL to select the remote’s cable mode. 2. Press SETTINGS, then ALL together until the TV button illuminates. 3. Press [0] , then [3] . • • Your TV output channel may also be 2 or 4.
RC-U49C+ REMOTE CONTROL (CONTINUED) Using M1, M2 buttons Using the programmed channels (previous page) as an example… 1. Press M1 Cable set-top terminal tunes to channel 001. 2. Press M1 again – Cable set-top terminal tunes to channel 012. 3. Press M1 again – Cable set-top terminal tunes to channel 123. 4. Press M1 again – Cable set-top terminal tunes to channel 231. 5. Press M1 again – Cable set-top terminal tunes to channel 017. 6. Press M1 again – Cable set-top terminal tunes to channel 1…. repeat.
RC-U49C+ REMOTE CONTROL (CONTINUED) How to Program the SmartKeys™ Your remote has two SmartKeys™ - CABLE and TV that operate in its cable mode. Each SmartKey™ can be programmed to transmit multiple functions. Programming and using the CBL SmartKey™ The CBL button normally turns on/off your cable set-top terminal. To program the CBL button to transmit multiple pre-programmed functions, follow the steps below: 1. Press MODE, then CBL to select the cable mode of your remote. 2.
RC-U49C+ REMOTE CONTROL (CONTINUED) Mode Lock™ Your CheckMate® IV remote can be set-up in two different operating modes - "locked" and "unlocked". From the factory, it is set in its "locked" mode, which means it will operate all the functions of your cable set-top terminal, plus a limited number of functions of your TV, VCR, DVD devices. In its locked mode, your remote is unable to change channels on your TV device.
AT8400 REMOTE CONTROL THE AT8400 ALLTOUCH® REMOTE CONTROL FUNCTIONS AS FOUR REMOTE CONTROLS IN ONE! Once programmed, it can control your TV, VCR, PVR, and any equipment connected to the AUX outputs.
AT8400 REMOTE CONTROL (CONTINUED) The steps described below are the same for each mode button. Repeat them for each device controlled by the remote, make sure you press the correct mode key for each device. PROGRAMMING THE AT8400 REMOTE CONTROL How to Program the TV Mode Key 1. Turn on the TV set, then press and hold the SELECT and TV keys until the TV mode key blinks twice. 2.
AT8400 REMOTE CONTROL (CONTINUED) How to Identify Programmed Codes 1. Press and hold the SELECT key and the appropriate mode key (AUX, VCR, TV or CBL) until the mode key blinks twice. 2. Enter carefully the code 9 9 0. After each digit the mode key will blink once. At the end of the operation it should blink twice. 3. Press 1, then count the number of times the mode key blinks. That number indicates the first digit in the code. If the mode key does not blink, the digit is 0. 4.
LIST OF CODES TV SETUP CODES Admiral – 107, 030, 061, 193, 056, 026, 054, 211 Advent – 072, 094, 425 Adventura – 060, 185, 047 Aiko – 106 Aiwa – 135, 214 Akai – 044, 053 Alaron – 193 Amark – 007, 086, 023, 215 Ambassador – 191 Ampro – 112 Amstrad – 006, 157 Anam - 194, 069, 088, 089, 093, 111, 120, 125, 134, 217, 218, 219, 220, 221, 222, 223 AOC – 033, 044, 070, 199, 053, 030, 038, 427 Audiovox – 106, 194, 465, 111, 220 Baysonic – 194 Belcor – 033, 073 Bell & Howell – 030, 168, 211 Bradford – 194 Brocksoni
LIST OF CODES (CONTINUED) VCR SETUP CODES Admiral – 062, 004l, 066, 075 Adventura – 014 Aiko – 292 Aiwa – 014, 051, 106, 132 Akai – 055, 075, 120, 011, 021, 098, 103, 269, 275, 336, 351, 352, 354 American High – 049 Asha – 254 Audio Dynamics – 007, 052, 243, 291 Audiovox – 051, 106, 194, 465 Beaumark – 254 Bell & Howell – 118, 060, 357 Broksonic – 016, 135, 198, 225, 030, 048, 333, 337, 358, 359 Calix – 051 Canon – 049, 034, 105, 086, 362 Carver – 095 CCE – 086, 292 Cineral – 292 Citizen – 051, 292, 006,