Important to user NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority. NOTE: This equipment has been tested and found to comply with the limits for a class B digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Important safety precautions The lightning within alert flash an equilateral the user "dangerous enclosure with arrowhead triangle, to the presence voltage" within a risk of electric CAUTION to of un-insulated the product's that may be of sufficient to constitute symbol, is intended magnitude to persons.
Important safety precautions Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, when liquid has been spilled or when objects have fallen into the apparatus, or when the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. POWER SOURCE: This TV should be operated only from the type of S3126A power source indicated on the marking label.
Important safety precautions 20. OVERLOADING: Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 21. OUTDOOR USE: Do not install this TV outdoor. If the TV is exposed to rain, it may result in a fire or an electric shock. If the TV is exposed to direct sunlight, the TV may heat up and cause damage to the TV. 22. VEHICLE: Do not install the TV in a vehicle. Bumping of the vehicle may cause the TV to fall down and cause injury. 23.
Important Safety Precautions To secure TV to stand or Wall, use hardware listed below (Not Supplied) 1. Attach the wall anchor on the stand. 2. Tie the ropes or chains with TV pedestal screws. Ropes or chains should be secure tightly. 3. Fasten the anchor bolts into top wall-mount holes. 4. Attach the wall anchors on the wall strong enough to support the weight of the TV. (Attach to the Wall Stud). 5. Make sure to connect anchor bolts to wall anchors.
Table of Contents 1.important to user ...................................................................................... 1 2.Important safety precautions .................................................................... Safeguards ....................................................................................... Safety Strap ...................................................................................... 2 2 5 3.Table of Contents .......................................................
Setting Up Installing the Stand @ 1. Lay a cloth or another soft material on a flat surface to avoid damage to the LCD screen. 2. Put the TV back upward and the LCD screen downward and keep it flat on the table-board. 3. Take out the stand and insert the stand into the installing slot in the lower part of the TV, then put the stand to relevant position of the TV set until all the holes match each other completely. 4. Fasten the stand and the TV set together with the 4 screws provided.
Wallomounting Bracket Installation 42LED55SA 47LED55SA 55LED55SA 200 x 200 200 x 200 400 x 400 Screw Diameter M6 M6 M8 Screw Length(Unit:mm) 25 25 25 Unit Dimension(Unit:mm) NOTE: Wall mount may vary depending instructions Removing bracket is not included with TV and mounting on brand and size of bracket. that came with wall mount Customer for specific of wall mount bracket to wall should consult bracket information on how to mount mounting bracket to wall. TV Stand 1.
Setting When Up Installing the TV Against a Wall or Enclosed Area Make sure that your TV has adequate air circulation. Allow enough space around the TV as shown below. Avoid operating the TV at temperatures below Inadequate air 45 ° F (5°C) Instand with stand 12 inches 2.375 inches 6cm 4 inches ... __ __ !U-L_d Leave at least this much space ar Install on the wall the set. 12inches 4 inches 4 inches 10cr'n _ Leave at least this much space around the set.
Setting Up TV Front Note:Touch the silk print area according to the need, the TV will response correctly. No. Component Component Description 1 POWER indicator 2 Remote sensor Receives signals from the remote control. Do not block. 3 Standby button Press to turn your TV on or off(Standby mode) 4 CH _' Press to go to the previous channel. 5 CH A Press to go to the next channel. 6 VOLT Press to decrease the volume. 7 VOLA Press to increase the volume.
Setting Up TV Rear f COMPONENT2 @Y-VIDEO I @ PB-- _t PR-- AV2 -1 (_) L-- [ @ R j SERVICE COAXIAL 0 _ HDMI 4 L The cable tie is only used for the power cord. Note: The appearance of 42LED55SA, for reference only.
Setting Up Warning: Before connecting the TV to any other electronic device, unplug the TV and electronic device AC cords from the AC input. Note: Not all following terminals are included on your TV. The actual one refer to "TV Rear". 1. Connect to broadcast antenna or the cable TV To have an optimal picture quality, it is strongly recommended to have an external antenna or a cable TV. Note: - It is recommended that coaxial cable (750) mismatched impedance.
Setting Up 3. Connecting Component Devices (DVD, DVR (digital video recorder), Blu-Ray) Component video(Y, Pb, Pr)transmits video as separate Y, Pb, Pr signals. Use this connection for high-definition video signals from a DVD or other equipment. - Connect Component video and audio cables to Component inputs ("PR/CR", "PB/CB", "Y") of your set and the other ends to corresponding component video out connectors on the PVR or DVD.
Setting Up 5. Connect to PC - Connect the D- Sub cable to "VGA" on the side of your set and the other end to the Video Card of your computer. - Connect the stereo audio cable to "PC AUDIO "on the side of your set and the other end to "Audio Out" of the sound card on your computer. Note: For some sets "PC AUDIO" share with component. z o _® < Computer 6. Connect to headphone - Connect the headphone jack of the TV set.
Using the remote Control Installing the remote control batteries 1. Open the battery cover on the back of the remote control. 2. Install two AAA size(1.5V) batteries. Match the "+" and "-" signs on the batteries to the signs on the battery compartment. 3. Close the battery cover. ! gent _y / .... push / ii Note: 1. 2. 3. 4. Dispose of your batteries in a designated disposal area. Do not throw the batteries into fire. Do not mix battery types or combine used batteries with new ones.
Remote Control Panel Buttons @ instructions (1) (2) (3) Power On/Off. Power indicator. INPUT: Switch among TV, Video, VGA. (4) (5) (6) (7) (8) (9) 0-9 Numbers: For direct channel access. Last: Return to previous channel. -- : Select digital channels. PICTURE: Picture Mode selecting. SOUND: Sound Mode selecting. DISPLAY: Display current status information. Component, HDMI and (10) MUTE: Mute the sound. (11 ) VOLA IV: Volume increase/Volume decrease. (12) CHA IV: Next channel/Previous channel.
Using the Remote Control Basic Operation Connecting power cord to the TV 1. Connect the power cord to the connector on the back of the TV, if the power cord in accessories. Note:When connecting the power cord to the connector of the TV, make sure the power cord is fully inserted in the place. Bad contact may cause high temperature of the connector and the risk of fire or other damages. 2. Connect the power cord to the AC power outlet. Power ON/OFF 1. Connect the TV to a power outlet.
Using the Remote Control Use [EXIT] button Press the [EXIT] button to exit the OSD menu. Select channels by numbers To select a channel: Press the channel number you would like to go to. For example, to select channel number 120, press buttons 1,2 and 0, respectively and then press [ENTER] to confirm. Use [MENU] button Press the [MENU] button to display the TV OSD menu. Use [LAST] button Press the [LAST] button to return to the previous channel.
Changing the TV Settings 1 2 3 Press [MENU_ button to display the main menu. Press [A/V] button to select TV item. Press [ _/ENTER] button to enter TV menu. 4 Press [A/T] button to select the option, press [P-/ENTER_ button to enter or press [_/_ button to adjust the option. Press the [Menu_ button to close the menu. 5 You can adjust: o Tuner Mode - Select the TV signal source. select Antenna You can or Cable.
Changing the TV Settings 1 2 Press [MENU] button to display the main menu. Press [A/T] button to select Video item. 3 4 Press [ I_-/ENTER] button to enter Video menu. Press [A/T] button to select the option, button to enter or press [4/1_] press [_/ENTER] button to adjust the option. Press the [Menu] button to close the menu. You can adjust: • Picture Mode - Adjusts the Picture Mode.
Changing MFC: the TV Settings To improve the perception of moving images. The weak setting is suitable for most programs is recommended for general viewing, strong settings can further enhance and normal and motion, however on some cases can create a halo effect on edges of moving objects. You may need to switch settings pending the contents your viewing.
Changing the TV Settings 1 Press [MENU] button to display the main menu. 2 Press [A/T] button to select Audio item. 3 Press [ I_/ENTER_ 4 Press [A/T] button to select the option, press [_/ENTER_ button to enter or press [4/_ button to enter Audio menu. button to adjust the option. Press the [Menu] button to close the menu. 5 You can adjust: - Balance - Adjusts the volume of the left and right speakers. - Surround Sound - Turns the surround sound effect on or off.
Changing the TV Settings 1 Press [MENU] button to display the main menu. 2 3 Press [A/T] button to select Setup item. Press [ I_/ENTER] button to enter Setup menu. 4 [A/T] button to select the option, [_-/ENTER_ button to enter or press [41/_ to adjust the option. the [Menu_ button to close the menu. Press press button 5 Press You can adjust: . OSD Language - Use the right or left arrow button to choose the OSD Language among English, Spanish and French.
Changing the "IV Settings _]_ Cinema Stretches the 4:3 aspect and horizontally ratio image vertically to fill the screen at 1:2,35 aspect ratio, Dot to dot Use the function to see the full image without any cutoff, when HDMI (720p/1080i/1080p), Component (1080i/1080p), DTV (1080i) or VGA signals are inputs. • DPMS - This is a good function for a computer monitor. control the screen on or off. For example, switched off.
Changing • Caption: the TV Settings There are three items in it - Analog Closed Caption, Digital Closed Caption and Digital Caption Style. This is a function about caption, display caption by anolog signal and display caption by digital signal. Analog Closed Caption: CCl, CC2, CC3, Cc4, TEXT1, TEXT2, TEXT3, TEXT4. Digital Closed Caption: Digital Caption Style: Service1, Service2, Service3, Service4, Service5, Service6. There are two Caption Styles.
Changing the TV Settings 1 Press [MENU] button to display the main menu. 2 Press CA/T] button to select Parental item. 3 Press C IP,/ENTER] button to enter Parental menu. 4 5 When you first use this function, password button to adjust the option. Press the [Menu] button to close the menu. the default is E0000]. Once you input this password, you can: Press A,/_' to highlight an option, then press 4/ option.
Changing the TV Settings Following is the description of these ratings.
Changing the TV Settings About Canada (French) Rating Description G General 8 ans+ 8+General; 13 ans+ Programming may not be suitable the age of 13 16 ans+ Programming is not be suitable for children under the age of 16 18 ans+ About Canada Not recommended for young children for children under Programming restricted to adults (English) Rating Description C Children C8+ Children eight years and older G General Programming, suitable for all audiences PG Parents Guidance 14+ Viewe
Appendix Before calling a service technician, please check the following table for a possible cause of the problem and some solutions. Customer important notice: If the TV can not be operated, please unplug the power and restart. Possible Symptoms Solutions • Make sure the power cord is plugged in, then press Power (Standby). TV will not turn on • The remote control batteries may be dead. Replace the batteries. = Unplug the VGA wire and plug the power wire again.
Appendix Model Screen Diagonal Size Screen Resolution 42LED55SA 47LED55SA 55LED55SA 42 inches 47 inches 55 inches 1920X1080 Power Consumption Pixels screws pattern M6X25mm Wall-mount dimension(VESA) 200mm X 200mm X WX HI Weight with base(Ibs) Pixels (4 pcs) M6X25mm (4 pcs) 200mm X 200mm 40.6x11.5x28.1 45x11.2x30.7 44.
SRS_ restores the original three-dimensional sound field of stereo recordings by retrieving spatial information buried in the recordings to create an immersive 3D sound-field using only two speakers or headphones. LBY DIGITAL I Manufactured under license from Dolby Laboratories. Dolby and the double D symbol are trademarks of Dolby Laboratories. This product contains electrical or electronic materials.