USER’S MANUAL 22” LED TV/DVD COMBO PLEDV2213A
Contents Introduction Warning Caution Important Information Attaching or Removing the Stand Installing Batteries to the Remote Control Identifying Front and Rear Panel Connection Suggestion Main Unit Description Remote Control OSD Basic Adjustment DVD Features How Do I Clean The TV Troubleshooting Specifications FCC Compliance Statement
Introduction Thank you very much for purchasing your LED TV. It serves as a normal colour TV and a PC monitor. To enjoy your set fully from the very beginning, read this manual carefully and keep it handy for future reference. INSTALLATION ķ Locate the receiver in the room where direct light does not strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing.
Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to avoid the risk of electric shock. This equipment may only be disassembled by qualified service personnel.
Caution Caution - High voltages are used in the operation of this product. Do not open the product's casing. Refer servicing to qualified service personnel . Caution To prevent fire or electrical shock hazard, do not expose the main unit to rain or moistureˈdo not place objects filled with liquids, such as vases, on the apparatus. Caution Do not drop or push objects into the television cabinet slots or openings. Never spill any kind of liquid on the television receiver.
Caution Caution Never stand on, lean on or suddenly push the product or its stand. You should pay special attention to children. Caution Do not place the main unit on an unstable cart stand, shelf or table. Serious injury to an individual and damage to the television may result if it should fall. Caution When the product is not used for an extended period of time, it is advisable to disconnect the AC power from the AC outlet.
Important Information Television Antenna Connection Protection External Television Antenna Grounding If an outside antenna or cable system is to be connected to the TV, make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and static charges.
Attacthing or Removing the Stand 1. To attach the base place the display unit flat on a table. Afterwards attach the stand onto the bottom of the stand. Screw in the 3 screws to secure the stand.
2.To remove the stand, remove the 2 screws in the area and the stand will come off. Installing Batteries to the Remote Control Please insert two AAA batteries into the remote control. Make sure that you match the (+) and (-) symbols on the batteries with the (+) and (-) symbols inside the battery compartment. Afterwards, re-attach the battery cover. Please note: Only use AAA batteries. Do not mix new and old batteries.
Identifying Front and Rear Panel Front View INDICATOR LIGHT – The light is red when power is plugged in but the TV is not turned on. The light turns blue when the TV is turned on. Because of the LED in the panel, the TV might take 10 – 12 seconds to power on. REMOTE SENSOR – The remote sensor receives all the commands from the remote control. Rear View Mounting Pattern Mounting Specification : 75mm x 75mm using screw size M4. Length of screw should not exceed 6mm.
Connection Suggestions If You Have Digital Cable without Cable Box or Antenna… 1. 2. 3. 4. Make sure the power of HDTV is turned off. Connect the RF cable from your antenna or digital cable to the TV port on the back of your HDTV. Turn on the HDTV. Follow the first time on screen instructions. Please Note: Not all broadcasts are in High Definition (HD). Please refer to your local broadcasting stations for more information.
Connecting Wii™ with Composite… 1. 2. 3. 4. 5. 6. Make sure the power of HDTV and your Wii™ is turned off. Obtain a Yellow Video Cable. Connect the Yellow Video connector to both your Wii™ and AV’s Yellow Video connector port on the back side of your HDTV. Obtain a RCA Audio Cable. Connect the white color connector to both your Wii™ and AV’s white connector port on the back side of your HDTV. Connect the red color connector to both your Wii™ and AV’s red connector port on the back side of your HDTV.
Connecting Cable or Satellite boxes with HDMI… 1. Make sure the power of HDTV and your set-top box is turned off. 2. Connect a HDMI cable to the HDMI output of your set-top box and the other end to the HDMI port on the back of your HDTV. 3. Turn on the HDTV and your set-top box. 4. Use the remote control’s source button or the source button on the TV to switch to HDMI. Please Note: Please reference the set-top box’s manual, to make sure the set-top box is configured to output correctly to the TV.
Connecting to a PC with VGA and 3.5 mm minijack … 1. Make sure the power of HDTV and your PC is turned off. 2. Obtain a 15-pin D-Sub VGA cable; connect to the VGA output of your PC and the other end to the VGA port on the back of your HDTV. 3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC and the other end to the VGA Stereo Input port. 4. Turn on the power of the HDTV and your PC. 5. Use the remote control’s source button or the source button on the TV to switch to PC. 6.
Main unit description Control Panel Button Function VOL+ : Increase volume; if OSD is active, functions as right in the menu; in SOURCE menu, functions as ENTER. VOL- : Decrease volume; if OSD is active, functions as left in the menu. CH+ : Change channel up; if OSD is active, functions as up in the menu CH- : Change channel down; if OSD is active, functions as down in the menu. MENU : Press to select the main menu. SOURCE : Select the input signal.
Remote control : Press this button to switch on the TV when at standby mode or enter standby mode. : Press this button to mute or restore sound. MTS/AUDIO˖In the TV condition, press this key to select the stereo mode/ Press this key to show the list of audio languages available for the current channel in ATSC or press to select the DVD audio (Used for models with DVD function only). ASPECT: Press to select the different picture size. PMODE: Select picture mode. SMODE: Select sound mode.
/FAV˖ ˖Press to start playing the disc or STORAGE , or to pause playing (Used for models with STORAGE or DVD function only)/ Switch between custom set "Favorite List". /F.LIST˖Press to play backward (Used for models with STORAGE or DVD function only)/ Press this key to display the Favorite List mode. /C.LIST˖Press to play forward (Used for models with STORAGE or DVD function only)/ Press this key to display the channel list mode.
Installation Guide Press MENU button to display the MAIN OSD MENU; Press Ż / Źbutton to select the MENU you want; Press ENTER button to enter the sub menu; Press ź / Ÿ button to select the option and then press Ż / Ź to adjust the value in the sub menu; You can press MENU button to go back to the upper menu or EXIT button to close the OSD. PICTURE You can select the type of picture, which best corresponds to your viewing. Press the “MENU” button to enter the OSD menu .
a. Press “c/d” button to select “Aspect Ratio” and press the “ e/f” button to select. b. Press “c/d” button to select “Noise Reduction” and press the “e/f” button to select. c. Press “c/d” button to select “Dynamic Contrast” and press the “ e/f” button to select “On” or “Off”. SOUND You can select the type of sound, which best corresponds to your listening. Press the “MENU” button to enter the OSD menu .Then press “e/f” button to select the “SOUND” menu. 1.
Note: The bǃcǃdǃeǃfǃg function it is only available in USER mode. 2. Press “c/d” button to select “MTS” and press the “e/f” button to adjust. Note: It is only available in ATV. 3. Press “c/d” button to select “Audio Language” and press the “e/f” button to adjust. Note: It is only available in DTV. 4. Press “c/d” button to select “AVL” and press the “e/f” button to select “On” or “Off”. TIME e/f” button to Press the “MENU” button to enter the OSD menu .Then press “e select the “TIME” menu. 1.
SETUP Press the “MENU” button to enter the OSD menu .Then press “e/f” button to select the “Setup” menu. 1. Press “d” button to select “OSD Language” and press the “e/f” button to select the OSD language which you desire. 2. Press “c/d” button to elect “Transparency” and press the “ e/f” button to select. 3. Press “c/d” button to select “OSD Timeout” the “e/f” button to adjust OSD timeout. 4. Press “c/d” button to select “Closed Caption” and press the “ENTER/f” button to enter sub-menu. a.
(a). Press “c/d” button to select “Mode” the “e/f” button to adjust. (b). Press “c/d” button to select “Font Style” the “e/f” button to adjust. (c). Press “c/d” button to select “Font Size” the “e/f” button to adjust. (d). Press “c/d” button to select “Font Edge Style” the “e/f” button to adjust. (e). Press “c/d” button to select “Font Edge Color” the “e/f” button to adjust. (f). Press “c/d” button to select “FG Color” the “e/f” button to adjust. (g).
a. Press “c/d” button to select “Audio Only” the “e/f” button to select “On” or “Off”. b. Press “c/d” button to select “Blue Screen” the “e/f” button to select “On” or “Off”. c/d” button to select “Restore Default” and press the “ENTER/f”, Press “e/f” 7. Press “c button selecting “Yes” to restore all setting to default setting default. 8. Press “c/d” button to select “Setup wizard” and press the “ENTER” button to enter sub-menu. a.
c. Press “c c/d” button to select “Time Zone” and press the “e/f” button to select time zone. d. Press “c/d” button to select “Daylight Saving Time” and press the “e/f” button to select “On” or “Off”. e. Press “c/d” button to select “Time Format” and press the “e/f” button to select “12-hour” or “24-hour”. f. Press “c/d” button to select “Go to next step” and press the “ENTER/f” button to enter next step. g. Press “c/d” button to select “Air/Cable” and press the “e/f” button to select “Air” or “Cable”. h.
LOCK Press the “MENU” button to enter the OSD menu .Then press “e e/f” button to select the “Lock” menu. 1. Press “d” button to select “Enter Password” and press select digital button to enter. Note: The default password is “0000” 2. Press ź / Ÿ button to select “Change Password”, then press “ENTER/f” button to adjust the value. If the password is changed, all of the passwords in the menu will be changed at the same time. Note: If you forget your password, you can use “1470” to enter any menu locked.
c. Press “c/d” button to select “HDMI” and press the “e/f” button to select “Block” or “Unblock”. d. Press “c/d” button to select “PC” and press the “e/f” button to select “Block” or “Unblock”. 5. Press “c/d” button to select “US Rating” and press “ENTER/f” button to enter sub-menu. a. Press “c/d” button to select “TV” and press “ENTER/f” button to enter sub-menu. Press “c/d” button to select and press ĀENTERāto block or unblock. b.
Note: The item is available only when current stream has downloadable rating data. 8. Press “c/d” button to select “Reset RRT” and press “ENTER/f” button to reset. Channel Press the “MENU” button to enter the OSD menu .Then press “e/f” button to select the “Channel” menu. 1. Press “d” button to select “AIR/CLABLE” and press the “e/f”button to select Cable or AIR. 2.
PC Setting Press the “MENU” button to enter the OSD menu .Then press “e/f” button to select the “Setup” menu. And then press “d” button to select “PC Setting” and press the “ENTER/f” button to enter sub-menu. 1. Press “c/d” button to select “H-Pos” and press the “e/f” button to adjust. 2. Press “c/d” button to select “V-Pos” and press the “e/f” button to adjust. 3. Press “c/d” button to select “Clock” and press the “e/f” button to adjust. 4.
DVD manual BASIC PLAY BACK IMPORTANT NOTE; Preparations Press the SOURCE button on the front panel or remote to select the DVD source. Basic playback 1. press EJECT to eject the disc. Place a disc into DVD player.
SUBTITLE Press “ SUBTITLE ”, the screen will display “ SUBTI-TLE 01/XX XXXXX “, “01” indicates the ordinal number of this language; “XX” indicates total number of language; “XXXXX” indicates the language of country, (the number of language depends on disc). This function can select up to 32 languages display-ed on screen.
SPECIAL FUNCTION PLAYBCK You can view Kodak picture CD and JPEG picture CD on this TV. Playback Insert a Kodak picture CD or JPEG picture CD into the DVD Player and the disc will be loaded Automatically. If the disc type can be identified, the player will start showing the pictures one by one (slide show mode).if a navigation menu will be displayed use the navigation buttons to select a file, then press the ENTER button.
DVD SYSTEM SETUP General Setup Process 1. press the DVD-SETUP button, the general setup page, preference page will be displayed in turn, or to select, the item, then press to 2. press enter the submenu. 3. press or to select, then press PLAY/PAUSE or ENTER to confirm. 4. press DVD SETUP repeatedly to exit the set-up menus. General setup page ASPECT RATIO DESCRIPTION When using the DVD with the internal TV, select 4:3/LB.
DVD SYSTEM SETUP(CONTINUED) General Setup Page TV Display: user can select different display wide model such as 4:3 PS, 4:3 LB, 16:9 WIDE. On Screen Display (OSD) Language: Users can select on-screen display Language. Screen Saver: if the screen saver is on, then there will be an animated picture of DVD on the screen whenever the DVD player is idle for more than 3 minutes. Last memory: memorize the chapter you have just watched.
Preference page The preference page is only available when there is no disc in the player . these settings are applied consistently to all discs which are inserted and played. TV Type: this player Supports different TV output, including Auto, NTSC, and PAL systems. Usually please set to Auto Parental:the parental control function works in conjunction with the different censorship classes assigned to DVDs.
Default: resets all settings (except password and parental lock status) for this DVD player back to the manufacturers original settings, press ENTER to perform the reset, Note; Some functions may not be available depending no the type of disc. ANALOG AUDIO SETUP PAGE 1.Press the DVD-SETUP button,the Analog Audio Setup Page, Preference Page will be displayed in turn. 2.press c or d to select,the item,then press to enter the submenu. 3.Press c or d to select then press PLAY/PAUSE or ENTER to comfirm. 4.
PLAYABLE DISCS The following discs can be played; DISCS LABEL CONTENTS DIMENSION DVD VIDEO Audio + video (moving picture) 12cm AUDIO CD Audio 12cm JPEG Video(picture) 12cm KODAK CD Video(picture) 12cm CD-R Audio or video (moving picture) 12cm CD-RW Audio or video (moving picture) 12cm CD+G Video(picture) 12cm MPEG4 Audio or video (moving picture) 12cm Support discs DVD, VCD, CD-R, CD-RW, SVCD, DVCD, HDCD, JPEG, CD+G, MPEG-4 Kodak CD , WMA.
DICS PROTECTION AND DVD CHARACTERSTICS ON HANDLING DISCS ON STORING DISCS Do not touch the playback side of the disc. . Do not store discs in a place subject to direct sunlight or near heat Do not attach paper or tape to disc. source, Do not store discs in place subject to moisture and dust such as a bathroom or near a humidifier. Store discs vertically in a case. Stacking or placing object on discs outside of their case may cause warping.
How do I Clean the TV? IMPORTANT 1. The power cable has to be removed from the socket before cleaning the TV. 2. Do not use volatile solvent (alcohol, rosin, and toluene) to clean the TV. These types of chemicals might damage the housing and the LED glass. Cleaning the bezel and remote control 1. Use a 100% cotton cloth or micro-fiber cloth for cleaning. 2.
Troubleshooting Troubleshooting The following table contains the common problems and the solutions to these problems. Please check this list before you contact the technicians. Problems Solutions Connect power cord correctly. Turn on power. NO PICTURE Connect video cable correctly. ABNORMAL Match the colors on the cables to the ports off the back of the television. I.E. red cable to red colored Select the input signal source with proper cable connection with the source button. COLORS port.
Problems Solutions Check your auto lock function’s settings inside the OSD. TV CHANNELS ARE BLOCKED You may have locked up some channels but forgot about them. UNIVERSAL REMOTE This TV follows NEC’s universal remote code. CODE Please check your hand book for NEC’s codes then apply them. THE TV TURNS ON OR This TV is a High Definition liquid crystal display panel TV. It requires a few more seconds than normal TVs OFF SLOWLY AND THE to power up and show the picture.
Problems Solutions A Different channels and inputs will sometimes have this effect because the channel signal’s own volume SWITCHING OR is already loud. CHANNEL There is no way remove this completely. CHANGES function that can combat this type of effect. SOURCE The TV has an AUTO VOLUME LEVEL Please make sure that function is turned on.
9.
(2)Audio Sound Mode Music/Standard/ Movie/User/Sport Auto Volume Control Yes Tone 150Hz/500Hz/1KHz/5KHz/10KHz/Balance Speakers 3 watt per channel (3) General Hybrid TV Tuner NTSC / ATSC / QAM (Digital Cable Ready) Channel auto scan Yes Sleep timer Off/5mins/10mins/15mins/30mins/60mins/90mins/120mins/180mins/240mins Standby power Under 1W Timing support-Video 480i / 480p / 720p / 1080i / 1080p 1360*768@60 Hz (NATIVE) 1024*768@60 PC timing 800*600@60 640*480@60 720x400@70 (4)NTSC/ATSC Soun
FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: This device may not cause harmful interference This device must accept any interference received, including interference that my cause undesired operation. Please Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
