Warranty

ManualsBrandsProslat ManualsStorage & OrganizationHeavy Duty Hoist (2-Pack)

295 D, boul. Industriel, Châteauguay (QC) J6J 4Z2

proslat.com 1-888-691-2944 // 450-691-294 4 info@proslat.com

Installation guide

HEAVY DUTY HOIST

TOOLS REQUIRED

BOX CONTAINS

WARNING

1 x

2 x

1 x 1 x 1 x 2 x

2 x

4 x

1 x

Measure the distance between the handle

bars and seat of the bike. Most adult bikes

are between 32” and 36”, we suggest install-

ing your hoist a maximum of 48” apart.

For kayaks or similar items, we suggest 6’ apart.

Drill

1/8’’ Drill bit

Star screwdriver

Tape measure

Please read installation carefully prior to installing. Before using the product thoroughly

test the fully-weighted product (with equipment in place) to ensure the product has been

installed properly. Do not allow children to play on product. Proslat is not responsible for

any damage resulting from improper installation, overloading or product failure.

STEP 1

Adjustable wrench

01— 08-12-2014

Summary of content (6 pages)

PAGE 1
HEAVY DUTY HOIST Installation guide TOOLS REQUIRED 1/8’’ Drill bit Drill Star screwdriver Tape measure Adjustable wrench BOX CONTAINS 2x 1x 4x 4x 1x 4x 1x 4x 1x 1x 2x 2x WARNING Please read installation carefully prior to installing. Before using the product thoroughly test the fully-weighted product (with equipment in place) to ensure the product has been installed properly. Do not allow children to play on product.
PAGE 2
WARNING It is important that your hoist is attached to a solid wood ceiling joist. The joist must be 2” x 4” or larger. STEP 2 PARALLEL PERPENDICULAR Verify which way your ceiling joists are. Hoist brackets can be mounted parallel or perpendicular. Use two wood screws each to mount the back pulley and the front pulley to the ceiling, ensuring the distance between the two matches the measurement made in step 1. Pre-drilling 1/8” pilot holes in the ceiling will make mounting the pulleys easier.
PAGE 3
STEP 5 Use two wood screws to mount the rope cleat to the wall. When the bike is up to the ceiling, the excess rope should be stored in the cleat. OVERHEAD WARNING Make sure that there are no obstructions to restrict operation of the bike lift. USING THE BIKE LIFT LOWERING THE BIKE Hook the bike handlebar and seat with the hooks and be sure the ropes are not twisted (for bulky items, attach nylon straps to hooks). The bike can now be raised to the ceiling by the pulling rope.
PAGE 4
PALAN ULTRA-ROBUSTE Guide d’installation OUTILS REQUIS Perceuse Mèche 1/8 po Tournevis étoile Gallon à mesurer Clé ajustable LA BOÎTE CONTIENT : 2x 1x 4x 4x 1x 4x 1x 4x 1x 1x 2x 2x AVERTISSEMENT Veuillez lire attentivement les instructions avant l’installation. Avant d’utiliser le produit, testez-le à sa charge maximale afin de vous assurez qu’il a été installé adéquatement. Ne pas permettre aux enfants d’utiliser ou de jouer avec le produit.
PAGE 5
AVERTISSEMENT Il est important que votre palan soit attaché à une poutre du plafond. La poutre doit être d’un minimum de 2 po x 4 po (5 cm x 10 cm). ÉTAPE 2 PARALLÈLE PERPENDICULAIRE Vérifiez de quelle direction sont vos poutres de plafond. Les supports plafonniers du palan peuvent être installés perpendiculairement ou parallèlement. Utilisez deux vis à bois pour installer chaque support au plafond en vous assurant que la distance entre les deux correspond à la mesure prise à l’étape 1.
PAGE 6
ÉTAPE 5 Utilisez deux vis à bois pour installer le taquet au mur. Lorsque votre vélo est au plafond, l’excédent de corde devrait être accroché au taquet. AVERTISSEMENT Assurez-vous d’enlever tout obstacle qui pourrait nuire au fonctionnement du palan. SOULEVEZ LE VÉLO DESCENDRE LE VÉLO Accrochez le guidon et le banc aux crochets et assurez-vous que les cordes ne sont pas mêlées (pour de plus gros articles, attachez les sangles de nylon aux crochets).