User's Manual
Table Of Contents
- Your Feedback Please
- How to Contact Us
- ProSoft Technology® Product Documentation
- Important Safety Information
- Recommended Antennas
- Antenna spacing requirements for user safety
- 1 Start Here
- 2 RLX2 Quick Setup
- 3 Planning the Network
- 4 Installing the Radios
- 5 Diagnostics and Troubleshooting
- 6 Detailed Radio Configuration / Diagnostics
- 7 RadioLinx Industrial Hotspot Browser
- 8 Reference
- 8.1 Product Overview
- 8.2 Compatibility with ProSoft RLXIB Series Radios
- 8.3 Dimensional Drawings
- Master Channel-Frequency Table
- 8.4 FCC Emission Regulations
- 8.5 Radio hardware
- 8.6 RLX2-IHA Detailed Specifications
- 8.7 RLX2-IHG Detailed Specifications
- 8.8 RLX2-IHNF Detailed Specifications
- 8.9 RLX2-IHW Detailed Specifications
- 9 Antenna Configuration
- 10 Support, Service & Warranty
- Glossary of Terms
- 802.11
- 802.11a
- 802.11b
- 802.11g
- 802.11i
- 802.11n
- Access Point
- Ad hoc Mode
- AES
- Amplifier
- Antenna
- ASCII
- Association
- Authenticate
- Authentication Server
- Band
- Bandwidth
- Base Station
- Baud Rate
- bps
- CACT
- Channel
- Channel Move Time
- Client, Radio Mode
- Client, Software
- Configuration PC
- dBi
- dBm
- DCE
- Decibel (dB)
- Default Gateway
- Device-to-Device Network (Peer-to-Peer Network)
- DFS
- DHCP
- Direct Sequence Spread Spectrum
- Directional Antenna
- Diversity Antenna
- DTE
- Dual Band
- EAP
- EIRP
- Encryption
- ESD
- ESSID
- Firmware
- Frequency Hopping
- Frequency Hopping Spread Spectrum
- Fresnel Zone
- Full-Duplex
- Gain
- Gateway
- Guard Interval (GI)
- Half-Duplex
- Hz
- IEEE
- IP Address
- Key
- LAN
- LED
- Line of Sight (LoS)
- Link point
- MAC ID
- Master device
- Mbps
- Megahertz
- MIC
- MIMO
- Modbus
- Modem
- Network
- Node
- Non-Occupancy Period
- Null Modem Cable
- Panel Antenna
- Parabolic Antenna
- Peer-to-Peer Network
- Point-Multipoint (Broadcast) Network
- Point-Multipoint (Modbus) Network
- Point-to-Multipoint
- Point-to-Point Network
- Poll
- Power Supply
- Protocol
- QoS
- Range
- Remote Access Point
- Remote device
- Repeater
- Repeater, Radio Mode
- RS-232
- RTU (Remote Terminal Unit)
- Sector Antenna
- Signal Diversity
- Signal Loss
- Signal Strength
- Simplex
- Site Survey
- Spectrum
- Spread Spectrum
- SSI
- Subnet Mask
- TKIP
- UART
- WAP
- WDS
- WEP
- Wi-Fi
- Wi-Fi CERTIFIED™
- Wi-Fi Interoperability Certificate
- Wi-Fi Protected Setup
- Wireless Gateway
- Wireless Network
- WLAN
- WPA
- WPA2
- Yagi Antenna
- Index
RadioLinx Industrial Hotspot Browser RLX2 Series ♦ 802.11a, b, g, n
User Manual Industrial Hotspot
7.5.9 Show Parents - All
The Show Parents function displays the possible alternate parents for a repeater
graphically in the topology view. The link from the repeater to its current parent
will be shown in red. If the repeater can hear other radios in the network, links to
those radios will be shown in blue. This gives a graphical representation of the
number of alternate paths available to a radio should its parent link go down. A
detailed list of each of the alternates can be seen by right-clicking and selecting
‘Scan List'. This list, though, shows not only radios in the same network but also
802.11 radios on other networks.
By selecting All, alternate paths for all repeaters in the network will be shown. By
selecting One, alternate paths will be shown only for the one repeater that is
currently selected.
Show Parents – All is only available in the Topology View.
7.5.10 Show Parents - One
This is similar to Show Parents – All except that only the current parent is shown.
7.5.11 Print Area
Use the Print Area command to show the border around the area of the IH
Browser window. To print, use the Print command on the File menu.
Page 110 of 161 ProSoft Technology, Inc.
November 29, 2012