User's Manual
Table Of Contents
- Your Feedback Please
- How to Contact Us
- ProSoft Technology® Product Documentation
- Important Safety Information
- Recommended Antennas
- Antenna spacing requirements for user safety
- 1 Start Here
- 2 RLX2 Quick Setup
- 3 Planning the Network
- 4 Installing the Radios
- 5 Diagnostics and Troubleshooting
- 6 Detailed Radio Configuration / Diagnostics
- 7 RadioLinx Industrial Hotspot Browser
- 8 Reference
- 8.1 Product Overview
- 8.2 Compatibility with ProSoft RLXIB Series Radios
- 8.3 Dimensional Drawings
- Master Channel-Frequency Table
- 8.4 FCC Emission Regulations
- 8.5 Radio hardware
- 8.6 RLX2-IHA Detailed Specifications
- 8.7 RLX2-IHG Detailed Specifications
- 8.8 RLX2-IHNF Detailed Specifications
- 8.9 RLX2-IHW Detailed Specifications
- 9 Antenna Configuration
- 10 Support, Service & Warranty
- Glossary of Terms
- 802.11
- 802.11a
- 802.11b
- 802.11g
- 802.11i
- 802.11n
- Access Point
- Ad hoc Mode
- AES
- Amplifier
- Antenna
- ASCII
- Association
- Authenticate
- Authentication Server
- Band
- Bandwidth
- Base Station
- Baud Rate
- bps
- CACT
- Channel
- Channel Move Time
- Client, Radio Mode
- Client, Software
- Configuration PC
- dBi
- dBm
- DCE
- Decibel (dB)
- Default Gateway
- Device-to-Device Network (Peer-to-Peer Network)
- DFS
- DHCP
- Direct Sequence Spread Spectrum
- Directional Antenna
- Diversity Antenna
- DTE
- Dual Band
- EAP
- EIRP
- Encryption
- ESD
- ESSID
- Firmware
- Frequency Hopping
- Frequency Hopping Spread Spectrum
- Fresnel Zone
- Full-Duplex
- Gain
- Gateway
- Guard Interval (GI)
- Half-Duplex
- Hz
- IEEE
- IP Address
- Key
- LAN
- LED
- Line of Sight (LoS)
- Link point
- MAC ID
- Master device
- Mbps
- Megahertz
- MIC
- MIMO
- Modbus
- Modem
- Network
- Node
- Non-Occupancy Period
- Null Modem Cable
- Panel Antenna
- Parabolic Antenna
- Peer-to-Peer Network
- Point-Multipoint (Broadcast) Network
- Point-Multipoint (Modbus) Network
- Point-to-Multipoint
- Point-to-Point Network
- Poll
- Power Supply
- Protocol
- QoS
- Range
- Remote Access Point
- Remote device
- Repeater
- Repeater, Radio Mode
- RS-232
- RTU (Remote Terminal Unit)
- Sector Antenna
- Signal Diversity
- Signal Loss
- Signal Strength
- Simplex
- Site Survey
- Spectrum
- Spread Spectrum
- SSI
- Subnet Mask
- TKIP
- UART
- WAP
- WDS
- WEP
- Wi-Fi
- Wi-Fi CERTIFIED™
- Wi-Fi Interoperability Certificate
- Wi-Fi Protected Setup
- Wireless Gateway
- Wireless Network
- WLAN
- WPA
- WPA2
- Yagi Antenna
- Index
RLX2 Series ♦ 802.11a, b, g, n Reference
Industrial Hotspots User Manual
8.5 Radio hardware
8.5.1 Radio power requirements
The RLX2 radios accept voltages between 10 and 24 VDC, with an average
power draw of less than 6 Watts. A detachable power connector comes with the
radio, as shown below. The connector terminals are labeled + (positive DC
connection) and - (DC ground connection).
The AC-to-DC power supply adapter supplied with the optional RLX-IHBTK
Bench Test Kit can be used. The DC power wires must be less than 3 meters in
length to meet regulatory requirements.
Important: When wiring the power connector supplied with the radio, be sure to
observe the proper polarity markings on the power connector. Wiring the
connector incorrectly can cause serious damage to the radio which will not
be covered under the ProSoft warranty.
The Power Connector (ProSoft part number 002-0116) is shown on the left in the
photo above. Note the + and – polarity markings. The wire installation tool
(ProSoft part number 357-0061) shown on the right is helpful for installing wires
into the spring-loaded contacts inside power connector.
ProSoft Technology, Inc. Page 123 of 161
November 29, 2012