User's Manual
Table Of Contents
- Your Feedback Please
- How to Contact Us
- ProSoft Technology® Product Documentation
- Important Safety Information
- Recommended Antennas
- Antenna spacing requirements for user safety
- 1 Start Here
- 2 RLX2 Quick Setup
- 3 Planning the Network
- 4 Installing the Radios
- 5 Diagnostics and Troubleshooting
- 6 Detailed Radio Configuration / Diagnostics
- 7 RadioLinx Industrial Hotspot Browser
- 8 Reference
- 8.1 Product Overview
- 8.2 Compatibility with ProSoft RLXIB Series Radios
- 8.3 Dimensional Drawings
- Master Channel-Frequency Table
- 8.4 FCC Emission Regulations
- 8.5 Radio hardware
- 8.6 RLX2-IHA Detailed Specifications
- 8.7 RLX2-IHG Detailed Specifications
- 8.8 RLX2-IHNF Detailed Specifications
- 8.9 RLX2-IHW Detailed Specifications
- 9 Antenna Configuration
- 10 Support, Service & Warranty
- Glossary of Terms
- 802.11
- 802.11a
- 802.11b
- 802.11g
- 802.11i
- 802.11n
- Access Point
- Ad hoc Mode
- AES
- Amplifier
- Antenna
- ASCII
- Association
- Authenticate
- Authentication Server
- Band
- Bandwidth
- Base Station
- Baud Rate
- bps
- CACT
- Channel
- Channel Move Time
- Client, Radio Mode
- Client, Software
- Configuration PC
- dBi
- dBm
- DCE
- Decibel (dB)
- Default Gateway
- Device-to-Device Network (Peer-to-Peer Network)
- DFS
- DHCP
- Direct Sequence Spread Spectrum
- Directional Antenna
- Diversity Antenna
- DTE
- Dual Band
- EAP
- EIRP
- Encryption
- ESD
- ESSID
- Firmware
- Frequency Hopping
- Frequency Hopping Spread Spectrum
- Fresnel Zone
- Full-Duplex
- Gain
- Gateway
- Guard Interval (GI)
- Half-Duplex
- Hz
- IEEE
- IP Address
- Key
- LAN
- LED
- Line of Sight (LoS)
- Link point
- MAC ID
- Master device
- Mbps
- Megahertz
- MIC
- MIMO
- Modbus
- Modem
- Network
- Node
- Non-Occupancy Period
- Null Modem Cable
- Panel Antenna
- Parabolic Antenna
- Peer-to-Peer Network
- Point-Multipoint (Broadcast) Network
- Point-Multipoint (Modbus) Network
- Point-to-Multipoint
- Point-to-Point Network
- Poll
- Power Supply
- Protocol
- QoS
- Range
- Remote Access Point
- Remote device
- Repeater
- Repeater, Radio Mode
- RS-232
- RTU (Remote Terminal Unit)
- Sector Antenna
- Signal Diversity
- Signal Loss
- Signal Strength
- Simplex
- Site Survey
- Spectrum
- Spread Spectrum
- SSI
- Subnet Mask
- TKIP
- UART
- WAP
- WDS
- WEP
- Wi-Fi
- Wi-Fi CERTIFIED™
- Wi-Fi Interoperability Certificate
- Wi-Fi Protected Setup
- Wireless Gateway
- Wireless Network
- WLAN
- WPA
- WPA2
- Yagi Antenna
- Index
Support, Service & Warranty RLX2 Series ♦ 802.11a, b, g, n
User Manual Industrial Hotspot
MIC
Message Integrity Check. One of the elements added to the TKIP standard. A
"signature" is added by each radio on each packet it transmits. The signature is
based on the data in the packet, a 64-bit value (key) and the MAC address of the
sender. The MIC allows the receiving radio to verify (check) that the data is not
forged.
MIMO
Multiple Input Multiple Output refers to using multiple antennas in a Wi-Fi device
to improve performance and throughput. MIMO technology takes advantage of a
characteristic called multipath, which occurs when a radio transmission starts out
at Point A and the reflects off or passes through surfaces or objects before
arriving, via multiple paths, at Point B. MIMO technology uses multiple antennas
to collect and organize signals arriving via these paths.
Modbus
The Modbus protocol provides the internal standard that the MODICON
®
controllers use for parsing messages. During communications on a Modbus
network, the protocol determines how each controller will know its device
address, recognize a message addressed to it, determine the kind of action to be
taken, and extract any data or other information contained in the message. If a
reply is required, the controller will construct the reply message and send it using
Modbus protocol.
Modem
Stands for MODulator-DEModulator, a device that converts digital signals to
analog signals and vice-versa. Analog signals can be transmitted over
communications links such as telephone lines.
N
Network
A series of stations or nodes connected by some type of communication medium.
A network may consist of a single link or multiple links.
Node
An address or software location on the network.
Non-Occupancy Period
The time during which a radio cannot return to a frequency where radar was
detected. This time is typically 30 minutes. Typically a radio will not return to a
channel where radar was previously detected unless absolutely necessary.
Null Modem Cable
A specialty cross-communication cable with female connectors on each end used
for direct connection between devices when no modems are present. Commonly
used as a quick and inexpensive way to transfer files between two PCs without
installing a dedicated network card in each PC.
Page 152 of 161 ProSoft Technology, Inc.
November 29, 2012