User's Manual
Table Of Contents
- Your Feedback Please
- How to Contact Us
- ProSoft Technology® Product Documentation
- Important Safety Information
- Recommended Antennas
- Antenna spacing requirements for user safety
- 1 Start Here
- 2 RLX2 Quick Setup
- 3 Planning the Network
- 4 Installing the Radios
- 5 Diagnostics and Troubleshooting
- 6 Detailed Radio Configuration / Diagnostics
- 7 RadioLinx Industrial Hotspot Browser
- 8 Reference
- 8.1 Product Overview
- 8.2 Compatibility with ProSoft RLXIB Series Radios
- 8.3 Dimensional Drawings
- Master Channel-Frequency Table
- 8.4 FCC Emission Regulations
- 8.5 Radio hardware
- 8.6 RLX2-IHA Detailed Specifications
- 8.7 RLX2-IHG Detailed Specifications
- 8.8 RLX2-IHNF Detailed Specifications
- 8.9 RLX2-IHW Detailed Specifications
- 9 Antenna Configuration
- 10 Support, Service & Warranty
- Glossary of Terms
- 802.11
- 802.11a
- 802.11b
- 802.11g
- 802.11i
- 802.11n
- Access Point
- Ad hoc Mode
- AES
- Amplifier
- Antenna
- ASCII
- Association
- Authenticate
- Authentication Server
- Band
- Bandwidth
- Base Station
- Baud Rate
- bps
- CACT
- Channel
- Channel Move Time
- Client, Radio Mode
- Client, Software
- Configuration PC
- dBi
- dBm
- DCE
- Decibel (dB)
- Default Gateway
- Device-to-Device Network (Peer-to-Peer Network)
- DFS
- DHCP
- Direct Sequence Spread Spectrum
- Directional Antenna
- Diversity Antenna
- DTE
- Dual Band
- EAP
- EIRP
- Encryption
- ESD
- ESSID
- Firmware
- Frequency Hopping
- Frequency Hopping Spread Spectrum
- Fresnel Zone
- Full-Duplex
- Gain
- Gateway
- Guard Interval (GI)
- Half-Duplex
- Hz
- IEEE
- IP Address
- Key
- LAN
- LED
- Line of Sight (LoS)
- Link point
- MAC ID
- Master device
- Mbps
- Megahertz
- MIC
- MIMO
- Modbus
- Modem
- Network
- Node
- Non-Occupancy Period
- Null Modem Cable
- Panel Antenna
- Parabolic Antenna
- Peer-to-Peer Network
- Point-Multipoint (Broadcast) Network
- Point-Multipoint (Modbus) Network
- Point-to-Multipoint
- Point-to-Point Network
- Poll
- Power Supply
- Protocol
- QoS
- Range
- Remote Access Point
- Remote device
- Repeater
- Repeater, Radio Mode
- RS-232
- RTU (Remote Terminal Unit)
- Sector Antenna
- Signal Diversity
- Signal Loss
- Signal Strength
- Simplex
- Site Survey
- Spectrum
- Spread Spectrum
- SSI
- Subnet Mask
- TKIP
- UART
- WAP
- WDS
- WEP
- Wi-Fi
- Wi-Fi CERTIFIED™
- Wi-Fi Interoperability Certificate
- Wi-Fi Protected Setup
- Wireless Gateway
- Wireless Network
- WLAN
- WPA
- WPA2
- Yagi Antenna
- Index
Detailed Radio Configuration / Diagnostics RLX2 Series ♦ 802.11a, b, g, n
User Manual Industrial Hotspot
Field
Description
Max Data Rate
The maximum data rate for the RLX2-IHA, -IHG, and –IHW radios is
specified in megabits per second. The allowed values are shown
above. The default maximum is 54 Mbits/sec.
Normally the Max Data Rate should be set to the maximum value.
However under poor operating conditions, reliability may improve if the
Max Data Rate is reduced.
Page 72 of 161 ProSoft Technology, Inc.
November 29, 2012