RLXIC-SG Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM May 29, 2009 USER MANUAL
Important Notice Because of the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (that is, it may have errors) or be totally lost.
Patents Portions of this product may be covered by some or all of the following US patents: 5,515,013 5,629,960 5,845,216 5,847,553 5,878,234 5,890,057 5,929,815 6,169,884 6,191,741 6,199,168 6,339,405 6,359,591 6,400,336 6,516,204 6,561,851 6,643,501 6,653,979 6,697,030 6,785,830 6,845,249 6,847,830 6,876,697 6,879,585 6,886,049 6,968,171 6,985,757 7,023,878 7,053,843 7,106,569 7,145,267 7,200,512 D442,170 D459,303 and other patents pending.
Contents User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Contents Important Notice.................................................................................................................................. 2 Safety and Hazards ............................................................................................................................ 2 Limitation of Liability..................................................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 7.3 7.4 7.5 8 Serial Modes ........................................................................................................... 55 Data Communication .............................................................................................. 60 Keepalive ................................................................................................................ 65 IP Manager 8.2 8.3 8.4 8.
Introduction to the RLXIC-SG User Manual 1 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Introduction to the RLXIC-SG In This Chapter ALEOS™.................................................................................................7 AceWare™ .............................................................................................. 8 Connecting to your cellular provider ........................................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 1.2 Introduction to the RLXIC-SG User Manual Extensive Machine Protocols Packet Level Diagnostics Device Management & Control Protocol Spoofing AceWare™ A wireless solution is not complete until you have software tools to manage the devices monitoring your valuable equipment.
Introduction to the RLXIC-SG User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Network Monitoring AceNet allows you to efficiently deploy, monitor, and maintain wireless networks of any size by enabling you to quickly configure an entire group of RadioLinx modems to the same parameter settings using templates built with AceManager.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 3 Introduction to the RLXIC-SG User Manual When your RLXIC-SG has received its IP address from your cellular provider, a connection to the Internet or the cellular network is also available for a computer or other device connected directly to the RLXIC-SG. The RLXIC-SG will perform a one-to-one routing for all internet traffic to and from the computer or other end device.
Introduction to the RLXIC-SG User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM If you need to contact your RLXIC-SG, a device connected to the RLXIC-SG, or a host system using the RLXIC-SG from the Internet, you need to have a known IP (such as one which is static) or domain name (an IP address which is converted by a DNS server into a word based name).
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Introduction to the RLXIC-SG User Manual Page 12 of 136 ProSoft Technology, Inc.
Specifications User Manual 2 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Specifications In This Chapter Interface Port Pin-Outs .......................................................................... 15 Power Connector................................................................................... 15 2.1.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Specifications User Manual 2.1.5 Power Consumption: (@12V DC) Transmit/Receive (Typical/Max) 350/450 mA Idle 104 mA Input Current 40 mA to 120 mA Input Voltage 9 - 28V DC 2.1.6 Standards/Approvals Carrier specific approvals FCC Industry Canada 2.1.
Specifications User Manual 2.2 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Interface Port Pin-Outs 2.2.1 Serial Port 2.3 Power Connector Warning: Explosion Hazard - Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous. ProSoft Technology, Inc.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Page 16 of 136 Specifications User Manual ProSoft Technology, Inc.
Activating RLXIC-SG on your cellular provider User Manual 3 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Activating RLXIC-SG on your cellular provider In This Chapter Installing the SIM................................................................................... 17 Configuring the APN..............................................................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Activating RLXIC-SG on your cellular provider User Manual Tools Required Small Phillips screw driver - The Phillips screw driver is the one which is also called a plus (+) or X screw driver. 3.1.2 Opening the Case 1 2 Unplug the RLXIC-SG power and all cables. Using a small Phillips head screw driver, remove the screws on the front of the RLXIC-SG. 3.1.
Activating RLXIC-SG on your cellular provider User Manual 3.2 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring the APN The APN (Access Point Name) is the way your modem knows how it will be communicating with the network. The APN allows custom IP addressing and tailoring your company's wireless IP solution to meet the security and IP addressing requirements of your applications.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 2 Activating RLXIC-SG on your cellular provider User Manual Select TCP, UDP, or PPP. Enter the connection information. o For UDP or TCP, enter 192.168.13.31 as the IP address. o For PPP, select the COM port to which the modem is connected. Note: The simplest way to connect to the modem is through a USB cable.
Activating RLXIC-SG on your cellular provider User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 3 Select MISC from the menu on the left side under the Common group. 4 Enter the NAI into the new value field for *NETUID, and enter your network password into the new value field for *NETPW. 3.2.4 Write the Settings to the RLXIC-SG 1 Click the Write button on the tool bar of AceManager.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Page 22 of 136 Activating RLXIC-SG on your cellular provider User Manual ProSoft Technology, Inc.
Hardware Installation of the RLXIC-SG User Manual 4 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Hardware Installation of the RLXIC-SG In This Chapter Connecting to Power ............................................................................. 24 Connecting to a Computer or other Device ........................................... 25 Indicator Lights ......................................................................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Hardware Installation of the RLXIC-SG User Manual Antennas selected should not exceed a maximum gain of 5 dBi under standard installation configuration.
Hardware Installation of the RLXIC-SG User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Warning: Explosion Hazard - Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous. 4.2 Connecting to a Computer or other Device Your RLXIC-SG's full-speed (12 Mbit) USB 2.0 port can be connected directly to most computers or other devices using a standard full-speed USB 2.0 cable.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Hardware Installation of the RLXIC-SG User Manual The Reset button (on the left side of the RLXIC-SG) has two functions. If it is quickly depressed and released, the modem will simply power cycle the internal hardware.
Hardware Installation of the RLXIC-SG User Manual 3 4 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Press the bracket down onto the DIN rail until flush. The locking tab snaps into position and locks the bracket to the DIN rail. If the bracket does not lock in place, use a screwdriver or similar device to move the locking tab down, press the bracket flush with the DIN rail and release the locking tab to lock the bracket in place. 4.4.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Hardware Installation of the RLXIC-SG User Manual 4.4.3 Mounting Bracket Dimensions Page 28 of 136 ProSoft Technology, Inc.
Configuring your RLXIC-SG User Manual 5 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring your RLXIC-SG In This Chapter Using AceManager ................................................................................ 29 Using Templates ................................................................................... 32 Using a Terminal Application with AT Commands.................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring your RLXIC-SG User Manual 5.1.1 Start AceManager START > ALL PROGRAMS > AIRLINK COMMUNICATIONS > ACEMANAGER 5.1.2 Connect to your RLXIC-SG 1 Click the CONNECT button. 2 Select a connection method: o If you are connecting remotely, you can use UDP, TCP, or SMS. o If you are connecting locally with the modem connected directly to your computer using a serial cable, you can use PPP.
Configuring your RLXIC-SG User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 5.1.3 Enter the configuration options 1 2 3 On the left side of AceManager is the GROUPS menu. Select the appropriate group as needed or directed. Enter your changes in the NEW VALUE column by typing in the desired change or using the drop down menus. The current configuration is shown in the VALUE column. 5.1.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 5.2 Configuring your RLXIC-SG User Manual Using Templates If you have a modem configuration that works well for your needs, using AceManager, you can save that modem's configuration as a template, and then apply it to other RadioLinx modems. 5.2.1 Creating the Template with AceManager 1 2 Configure the "master" modem.
Configuring your RLXIC-SG User Manual 5 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Type in a file name that is descriptive of the template (so you can find it easily later), and save it to a location on your computer. 5.2.2 Applying a Template to one modem with AceManager You can use a template you created yourself, using the steps above, or a template provided by your RadioLinx representative or someone in your company who has set up a modem template.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring your RLXIC-SG User Manual 3 Click the WRITE button on the toolbar to write the configuration to the modem. Wait for the "Write Successful" message. 4 Reset the modem. Caution: Many of the configuration settings will not take effect until the modem has been reset. Tip: You can use common settings on one modem to configure those same settings on another modem even of a different type.
Configuring your RLXIC-SG User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Tip: Click on the first with your mouse, and, with the control button held down, click the additional modem. 2 Select the MODEM option in the tool bar, and then select APPLY ACEMANAGER TEMPLATE. 3 Either type in the Template file name, or click browse, and select the template file you want to apply (you may need to change folders).
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 5.3 Configuring your RLXIC-SG User Manual Using a Terminal Application with AT Commands You can access and configure your RLXIC-SG using a terminal application such as Microsoft HyperTerminal, PuTTY, or similar. The following directions are for HyperTerminal which is part of a standard installation of Windows XP.
Configuring your RLXIC-SG User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Note: You can also connect using the virtual USB serial port. Refer to Using the USB virtual serial port with a Terminal Emulation Utility (page 50) for more information on configuring and using the virtual serial port. 2 3 Type in 192.169.13.31 for Host Address. Change the "Port Number" to 2332. 4 Click OK.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring your RLXIC-SG User Manual Tip: If you have configured the RLXIC-SG for settings different than the defaults for Bits per Second, Data Bits, Parity, and/or Stop Bits, you will need to use your changed settings. 2 Click OK. Connected 1 Type AT and press ENTER. You should get a reply of "OK" or "0". 2 To see what you are typing as you type it, you will need to turn on the echo and verbose mode.
Configuring your RLXIC-SG User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Optional parameters are denoted with square brackets [ ]. AT Commands are not case sensitive. A capital "E" is the same as a lowercase "e". When you are using a terminal connection, if you enter a command which is recognized by the RLXIC-SG, it will respond with "OK". If the command is not recognized, the response will be "ERROR".
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Page 40 of 136 Configuring your RLXIC-SG User Manual ProSoft Technology, Inc.
Universal Serial Bus (USB) User Manual 6 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Universal Serial Bus (USB) In This Chapter Changing the USB port communication ................................................ 41 Installing the USB driver ........................................................................ 42 Using the Virtual Ethernet Port ..............................................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 6.2 Universal Serial Bus (USB) User Manual Installing the USB driver 6.2.1 Set the Port Type Virtual Ethernet port is the default setting for the USB port. If you want to install the virtual serial port, change the USB port configuration using the directions above. 6.2.
Universal Serial Bus (USB) User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 6.2.3 Install the driver from a specific location 1 Select and/or enter the location of the driver. o If the driver is on the CD, and the CD is in your drive, you can just select Search removable media. o If you have installed AceManager or the Setup Wizard, the drivers have been conveniently copied to your hard drive.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Universal Serial Bus (USB) User Manual 6.2.4 Optional: Verify and Configure the Virtual Port Settings Virtual Ethernet The USB Ethernet connection will show up in your Network Connections as a Local Area Connection. Tip: If you also have an Ethernet card on the computer or have installed the USB Ethernet to more than one USB port on your computer, the USB Ethernet may show up with a number.
Universal Serial Bus (USB) User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 3 Select the HARDWARE tab, and click the DEVICE MANAGER button. 4 Click on the + in front of NETWORK ADAPTERS. The newly installed driver, AirLink USB Ethernet/RNDIS, should be displayed.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Universal Serial Bus (USB) User Manual Virtual Serial You can verify the installation by looking in the Device Manager. 1 2 3 Click on START > CONTROL PANEL. Double-click on the SYSTEM icon. Select the HARDWARE tab, and click the DEVICE MANAGER button. 4 Click on the + in front of MODEMS. The newly installed driver, AirLink USB Serial Port, should be displayed. Page 46 of 136 ProSoft Technology, Inc.
Universal Serial Bus (USB) User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Tip: If the driver is displayed with a # and number behind the driver name (such as, AirLink USB Serial Port #2), it means more than one is installed on your computer, most likely for different USB port. More than one copy of the driver should not cause any problems, because only the connected port, and its driver would be active.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Universal Serial Bus (USB) User Manual 2 Select the Advanced tab, and click the Advanced Port Settings button. 3 At the bottom of the screen, the current port used will be listed. Use the drop down menu to select an available COM port number if you need to change it. Page 48 of 136 ProSoft Technology, Inc.
Universal Serial Bus (USB) User Manual 6.3 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Using the Virtual Ethernet Port After the driver is installed, you can use the USB port just like a standard Ethernet port. 6.3.1 Using USB Ethernet with AceManager In AceManager, use the UDP or TCP connection, and enter the IP address of the modem (192.168.13.31 by default), and the password (12345 by default). 6.3.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 6.4 Universal Serial Bus (USB) User Manual Using the Virtual Serial Port After the driver is installed, you can use the USB port just like a standard serial port. 6.4.1 Using the USB virtual serial port with AceManager In AceManager, the USB virtual serial port connection will appear as a standard serial port. Use the PPP connection, and select the COM# serial port of the USB connection.
Data Communication and Host Modes User Manual 7 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Data Communication and Host Modes In This Chapter Basic Modes.......................................................................................... 52 Serial Modes ......................................................................................... 55 Data Communication ..........................................................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Data Communication and Host Modes User Manual 7.1.2 Serial Modes PPP Mode: The RLXIC-SG uses PPP to communicate with a device or computer connected to the serial or USB port. SLIP Mode: The RLXIC-SG uses SLIP to communicate with a device or computer connected to the serial or USB port.
Data Communication and Host Modes User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM If the serial port of the RLXIC-SG is in any mode other than AT or PassThru, the AT command mode can be re-entered by: Deactivating DTR (if &D2 or Ignore DTR, S211, is not set). Issuing the +++ escape sequence (if Disable AT Escape, DAE, is not set). Resetting or Power cycling the modem.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Data Communication and Host Modes User Manual 7.2.3 PassThru Mode In PassThru mode, the RLXIC-SG does not behave normally, all port communication is passed directly between the internal hardware and the computer connected directly to the modem. This mode can be used to configure hardware-specific settings. For example, provisioning, troubleshooting, communicating with legacy equipment, etc.
Data Communication and Host Modes User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 7.2.4 Telnet Mode In AceManager you can configure Telnet operation. If you need to change the port for Telnet (for example, you have the default port blocked on your firewall), the option is on the OTHER tab. The default telnet port is 2332. You can also change the Telnet timeout, if the connection is idle, default 2 minutes. 7.3 Serial Modes 7.3.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Data Communication and Host Modes User Manual In response to any of the preceding commands, the RLXIC-SG will respond with CONNECT a carriage return and new line and is ready for the host to begin PPP negotiations.
Data Communication and Host Modes User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM When the modem is in UDP PAD (Packet Assembly and Disassembly) Mode, all characters received on the serial port are assembled into UDP packets, and sent to the remote IP address/port or the RLXIC-SG, and any packets received from the same IP/port-destined for the device port of RLXIC-SG (see *DPORT)--are disassembled, and dumped onto the serial line.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Data Communication and Host Modes User Manual When the session is initiated by serial data, the new session will be established using the destination address specified in S53. The S53 setting can be changed if the connect to last UDP setting (*UDPLAST=1) is set. The address in S53 will be updated to reflect the address of the last session initiated by an incoming UDP packet.
Data Communication and Host Modes User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 7.3.4 TCP and TCP Pad When the RLXIC-SG is in a TCP session, all characters received on the serial port are assembled into TCP packets, and sent to the mode's remote IP address/port, and any packets received from the remote end of the TCP connection are disassembled, and dumped onto the serial line.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 7.4 Data Communication and Host Modes User Manual AT Command Hybrid Mode (MD5) Hybrid Mode2 (MD6) MD 3 3 S82 2 2 S0 1 1 *UDPLAST 0 1 Data Communication Note: The RLXIC-SG forwards messages to and from the cellular network for only ONE device per port. The RLXIC-SG is a one-to-one gateway, and does not have advanced routing features required to do one-to-many routing.
Data Communication and Host Modes User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM *HOSTPRIVMODE - Set to 1 to enable the explicit IP addresses. *HOSTPRIVIP - Set to the IP address you want the RLXIC-SG to give to your device. DHCP network Mask - The subnet mask that is passed to the DHCP client on the Host device. *HOSTPEERIP - Set to the IP address you want for the RLXIC-SG. *HOSTNETMASK - Set to the subnetmask, generally 255.255.255.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Data Communication and Host Modes User Manual Additional Connected Networks If you have a router connected to the RLXIC-SG with additional networks configured behind that router, you can specify them in the PPP/Ethernet group of AceManager. Configure the Network the Host Network Mask for up to two additional networks. 7.4.
Data Communication and Host Modes User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM In AceManager, enter the fields in the Port Forwarding group. Number of PF Entries: Set value to number of used Port forward rules for performance gain. Each forwarding entry has four parameters: o Public Port: Port number of the Modem/Gateway. o Host/IF: Physical connection type to the modem. (USB, Ethernet, Serial).
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Data Communication and Host Modes User Manual Note: Port Filtering Mode does not require to be set when you enable Non-Friends Port Forwarding. Port Filtering Mode: Independent of the IP filtering, this mode can be enabled to block ports specified or allow ports specified. When enabled, all ports not matching the rule will be allowed or blocked depending on the mode.
Data Communication and Host Modes User Manual 7.5 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Keepalive Keepalive is used to test the connection to the cellular network by pinging an IP address after a specified period of inactivity. Keepalive is only recommended for users who have a remote terminated modem that infrequently communicates to the network or if you have experienced issues over time where the modem can no longer be reached remotely.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Data Communication and Host Modes User Manual 7.5.2 Data usage using Keepalive Keepalive is an optional feature. If you frequently pass data with your modem, you most likely do not need to have Keepalive enabled. When using Keepalive, be aware that a ping moves approximately 66 bytes of data over the network, and is billable by your cellular provider.
IP Manager User Manual 8 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM IP Manager In This Chapter Understanding Domain Names ............................................................. 68 Dynamic Names .................................................................................... 69 Using IP Manager with your RLXIC-SG ................................................ 69 Understanding DNS ..............................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM IP Manager User Manual Because many cellular providers, like wire-based ISPs, do not offer static IP addresses or static address accounts cost a premium vs. dynamic accounts, IP Manager works with a Dynamic DNS server to receive notification from RLXIC modems to translate the modem's dynamic IP address to a fully qualified domain name.
IP Manager User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Tip: A URL (Universal Resource Locator) is different from a domain name in that it also indicates information on the protocol used by a web browser to contact that address, such as www.prosofttechnology.com. www.prosoft-technology.com is a fully qualified domain name, but the http://, the protocol identifier, is what makes the whole thing a URL. 8.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM IP Manager User Manual *MODEMNAME : The name you want for the modem. There are some restrictions listed below for the modem name. *DOMAIN : The domain name to be used by the modem. This is the domain name of the server configured for *IPMANAGER1. *IPMANAGER1 : The IP address or domain name of the dynamic DNS server which is running IP Manager. *IPMANAGER2 : The secondary server for the domain.
IP Manager User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 8.4.2 Eairlink.com As a service, ProSoft Technology offers an IP Manager server, which can be used for any RadioLinx Intelligent Cellular modem. Note: The IP Manager service is currently not a guaranteed service, although every effort is made to keep it operational 24/7. *DOMAIN : eairlink.com *IPMANAGER1 : edns2.eairlink.com *IPMANAGER2 : eairlink.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM IP Manager User Manual *DNSUPDATE - This command sets how often you want DNS Updates to be requested. Otherwise the RLXIC-SG will only send updates when it is reset, powered up, or the IP address is granted by network changes. Use Alternate DNS 2 - Set another DNS User. Note: You can set up a second DNS User, if you have two DNS users.
Configuring Modbus/BSAP User Manual 9 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring Modbus/BSAP In This Chapter Modbus Overview.................................................................................. 73 Configuring the RLXIC-SG at the Polling Host for Modbus on UDP...... 75 Configuring the Remote RLXIC-SGs for Modbus with UDP ..................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring Modbus/BSAP User Manual 9.1.3 Supervisory Control and Data Acquisition (SCADA) Supervisory Control and Data Acquisition (SCADA) describes solutions across a large variety of industries, and is used in industrial and engineering applications to monitor and control distributed systems from a master location.
Configuring Modbus/BSAP User Manual 9.2 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring the RLXIC-SG at the Polling Host for Modbus on UDP This section covers a Polling Host with standard Modbus, variations may need additional AT commands. 9.2.1 Configure the listening/device ports In AceManager, select MISC in the side menu.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring Modbus/BSAP User Manual MD13: Modbus ASCII MD23 : Modbus RTU (Binary) MD33: BSAP MD63: Variable Modbus - individual parameters are set up manually. 9.2.3 Configure IP addresses for the Modbus IDs. The last step of configuring the modem at the host is setting the IDs to their specific IPs. In AceManager, select the menu option ADDR LIST. Addresses can be entered in decimal or hex.
Configuring Modbus/BSAP User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM With names instead of IP addresses for the Address List, the host modem will query the DNS server for the current IP address assigned to the specific name of a remote modem to send a message corresponding to the ID.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuring Modbus/BSAP User Manual The destination port for the modem at the host needs to match the device port in use on all the modems at the remote sites. For example, if the remote modem's device port (see below) is "12345", then the Modbus host modem's S53 destination port should be set to "12345". Set the destination port (S53) to match the device port of the host modem (*DPORT).
Configuring Modbus/BSAP User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 9.3.4 Configure other RTU settings. Other parameters may need to be changed, but this is dependent on the RTU type being used. As a minimum, this typically involves setting the proper serial settings to match your RTU. 9.3.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Page 80 of 136 Configuring Modbus/BSAP User Manual ProSoft Technology, Inc.
SNMP : Simple Network Management Protocol User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 10 SNMP : Simple Network Management Protocol In This Chapter SNMP Configuration.............................................................................. 82 SNMP MIB Definition Sample................................................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 10.2 SNMP : Simple Network Management Protocol User Manual SNMP Configuration To configure your RLXIC-SG to work as an SNMP agent, you can use either AceManager, or a terminal connection to configure the modem using AT commands. In AceManager, the SNMP commands are all part of the Other group under the Common group.
SNMP : Simple Network Management Protocol User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 10.2.3 User Name and Password The user name is "user". The user name cannot be changed. The RLXIC-SG's password is used as the SNMP password (default is "12345"). To change the password in the RLXIC-SG, select Modem from the top menu line in AceManager. The current password will be pre-entered.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 10.
SNMP : Simple Network Management Protocol User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM ::= { general 8 } -- COMMON -date OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { common 1 } otaProgrammingEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current ::= { common 2 } devicePort OBJECT-TYPE SYNTAX INTEGER(0..
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM SNMP : Simple Network Management Protocol User Manual MAX-ACCESS read-only STATUS current ::= { common 10 } -- STATUS -ipAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current ::= { status 1 } netState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { status 2 } netChannel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current ::= { status 3 } rssi OBJECT-TYPE
SNMP : Simple Network Management Protocol User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM STATUS current ::= { gps 2 } latitude OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { gps 3 } longitude OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { gps 4 } END 10.3.1 Display Responses The string that is displayed for these objects is the same display for the corresponding AT Command.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Page 88 of 136 SNMP : Simple Network Management Protocol User Manual ProSoft Technology, Inc.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 11 Configuration Commands In This Chapter Info (information) ................................................................................... 89 Status .................................................................................................... 91 Common................................................................................................
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual *NETPHONE? The modem's phone number, if applicable or obtainable. &V View active profile, the contents of the active registers. Not displayed with AceManager. In n=0 : Product name (for example, RLXIC-SG). n=1 : The RLXIC-SG's firmware (ALEOS) version, hardware ID, and copyright. n=2 : The internal hardware's firmware version, and relevant hardware ID.
Configuration Commands User Manual 11.2 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Status Most of the commands in the "Status" group have read-only parameters, and provide information about the modem. The Status Group has more fields that can be displayed on most screens. You can either resize your window or use the scroll bar on the side to display the remainder. *BOARDTEMP? The temperature, in Celsius, of the internal hardware.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual *NETOP? The current cellular carrier from the modem's firmware version, for example, your cellular provider. *NETRSSI? The current RSSI (Receive Signal Strength Indicator) of the RLXIC-SG as a negative dBm value. Tip: The same information is displayed with the command S202?. *NETSERV? The type of service being used by the modem, for example Tech.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 11.2.2 AT Commands Requiring PassThru mode These commands are not displayed in AceManager. 11.3 Common The groups under the heading Common encompass those commands that are common to most RadioLinx modems. 11.3.1 Misc (Miscellaneous) The commands of the "Misc" group are a variety of commands that do not directly fit in other categories.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual Tip: DAE=1 disables the +++ command. A/ Note: A/ is not proceeded by AT. Re-execute last command. A/ is not used in AceManager. A Manually answer an incoming connection. A is not used in AceManager. D[method][d.d.d.d][/ppppp] or D[method][@name][/ppppp] Dial a connection to a remote IP and Port using method. Cannot be configured in AceManager.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM DS=n Allows a PPP connection to be initiated on the host port. n=2 : Initiates the PPP connection. Cannot be configured in AceManager. Hn Hang-Up Command. n=1 : Hang-up With an AT telnet connection, this command will terminate the host data mode, and return the RLXIC-SG to an AT mode. Cannot be accessed in AceManager.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual Z Reset the RLXIC-SG. In AceManager, this command is performed with the Reset option on the toolbar. Tip: *DATZ=1 will disable Z. &W Writes all changed modem settings. If this command is not issued, any modified values will revert back to their previous values at modem reset. Cannot be configured in AceManager. *DATE=[mm/dd/yyyy],[hh:mm:ss] Sets and queries the internal clock.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM *NETUID=uid The login that is used to login to the cellular network, when required. uid=user id (up to 64 bytes) *STATICIP=d.d.d.d Set the static IP required to be received from the network. If the modem does not get this IP address from the network, it will reset the internal hardware, and try again. The default is 0.0.0.0, which allows any IP address from the network.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual En Toggle AT command echo mode. n=0 : Echo Off. n=1 : Echo On. Note: With more than one connection types (serial, and Telnet, and USB) the echo command can be set differently on each interface. USB is only available on RLXIC Serial radios. Qn The AT quiet-mode setting. If quiet mode is set, there will be no responses to AT commands except for data queried.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM S10=n Specifies the amount of time that the carrier from the remote modem can be lost before the modem goes on-hook. This allows temporary disruptions to carrier without disconnecting. A setting of 255 causes the modem to disable Carrier Detect, and presume carrier is always present. Cannot be configured in AceManager.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual Vn Command Response Mode. n=0 : Terse (numeric) command responses n=1 : Verbose command responses (Default). Xn Extended Call Progress Result mode. n=0 : Turn off extended result codes (Default). n=1 : Turn on result codes. This adds the text 19200 to the CONNECT response. &Cn Set DCD mode. n=0 : Always assert DCD.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM \Qn Set or query the serial port flow control setting. n=0 : No flow control is being used. n=1 : RTS/CTS hardware flow control is being used. n=4 : Transparent software flow control. Uses escaped XON and XOFF for flow control. XON and XOFF characters in data stream are escaped with the @ character (0x40). @ in data is sent as @@.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual Tip: Flow control (AT\Q) will override this indication, so if you want to use CTS to indicate network coverage, flow control has to be off (AT\Q0). *MODEMHISPEED Set the internal serial link speed to the internal (radio) module.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM S0=n This register determines how the RLXIC-SG responds to an incoming TCP connection request. The RLXIC-SG remains in AT Command mode until a connection request is received. DTR must be asserted (S211=1 or &D0), and the RLXIC-SG must be set for a successful TCP connection. The RLXIC-SG will send a "RING" string to the host.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual Caution: TCPT should never be 0 when using the TCP mode. A broken TCP session can result in the modem being left with a TCP half-open connection that can only be terminated with a reset. *ENQ=n Outputs an ENQ [0x05] after the TCP CONNECT delayed by the Delay Connect Response time (S221). n=0 : Disabled (Default). n=1 : Enable ENQ on CONNECT. 11.3.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM MDhh Default power-up mode for the serial port: When the RLXIC-SG modem is powercycled, the serial port enters the mode specified by this command after 5 seconds. On startup, typing ATMD0 within 5 seconds changes the mode to normal (AT command) mode. See also S53 to set the port for UDP or TCP. S82=n Enables UDP auto answer (half-open) mode.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual *USD=n Waits the specified delay before sending the first UDP packet and the subsequent UDP packets out to the port Ethernet. n=0 : No UDP packet delay (Default). n=1 - 255 : Delay in 100 ms units, from 100 ms to 25.5 sec. 11.3.5 DNS This group includes commands specific to the modem being able to use domain names instead of IP addresses for other configuration options.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 11.3.6 Dynamic IP This group includes commands specific to dynamic DNS. Dynamic DNS allows the RLXIC-SG to use a dynamic IP address account, with an IP address that can change each time you connect, and still allow you to use a fully qualified domain name to contact the RLXIC-SG using IP Manager running on a server with a dynamic DNS updater.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual *IPMGRKEYn=key Sets the 128-bit key to use to authenticate the IP update notifications. If the key's value is all zeros, a default key will be used. If all the bytes in the key are set to FF, then no key will be used (that is, the IP change notifications will not be authenticated).
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 11.3.7 PPP/Ethernet This group includes commands specific to PPP (serial) or Ethernet connections between the RLXIC-SG and a connected device. *DHCPSERVER=n Act as a DHCP server for any Ethernet device connecting to the RLXIC-SG.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual *HOSTNETMASK=n.n.n.n Subnet mask for the host interface. Allows communication with a subnet behind the host interface. n.n.n.n = subnet mask, example 255.255.255.0. *HOSTPEERIP=d.d.d.d Set or query the IP address that can be used to directly contact the RLXIC-SG after a cellular connection is established. If this value is not specified, 192.168.13.31 will be used. d.d.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 11.3.8 PassThru PassThru Mode is used to communicate directly to the RLXIC-SG internal hardware. Caution: While the modem is in PassThru mode, ALEOS is disabled. If you need to connect to the RLXIC-SG while it is in PassThru mode, you will need to do so with a terminal application. Not all commands are available while the modem is in PassThru mode.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual *PTREFRESH=n Number of minutes of inactivity in PASSTHRU mode to resend the *PTINIT string to the hardware module. n=0 : Disabled n=1-255 minutes *RESETPERIOD=n In PASSTHRU mode, modem will be reset after this period if no data has been sent or received. Value is in hours. n=0 : Disabled n=1-255 hours 11.3.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM *SMTPFROM=email Sets the email address from which the SMTP message is being sent. email=email address (maximum: 30 characters). *SMTPPW=pw Sets the password to use when authenticating the email account (*SMTPFROM) with the server (*SMTPADDR). pw= password Note: Not required to use SMTP settings but may be required by your cellular carrier.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual 11.3.10 Other DAE=n AT Escape Sequence detection. n=0 : Enable n=1 : Disable *DATZ=n Enables or disables reset on ATZ. n=0 : Normal Reset (Default). n=1 : Disable Reset on ATZ. *IPPING=n Set the period to ping (if no valid packets have been received) a specified address (*IPPINGADDR) to keep the modem alive (online).
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM *MSCIUPDADDR=name[/port] Modem Status Update Address - where Name/Port is the domain name and port of the machine where the modem status updates will be sent. The status parameters of the RLXIC-SG are sent in an XML format. name=domain name port=port *MSCIUPDPERIOD=n Modem Status Update Period - where n defines the update period in seconds. n=0 : Disabled.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual n=2 : Authentication and encryption, equivalent to "authPriv" setting in SNMPv3. SNMPv3 is required to do authentication and encryption, SNMPv2c and SNMPv3 authNoPriv transmissions will be silently discarded. Messages are both authenticated and encrypted to prevent a hacker from viewing its contents. *SNMPTRAPDEST=host/[port] Controls destination for SNMP Trap messages.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 11.3.11 Firewall Firewall Mode can limit access to the RLXIC-SG from the cellular network and the Internet. Basic Firewall functions are available via AceManager. Caution: If you are using Firewall mode you will not be able to use AceManager remotely or Telnet to the modem unless you are contacting the modem from one of the configured IP addresses.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual Fn=[d.d.d.d] Friends List IP address. n=0-9 Friends list index d.d.d.d = IP address Using 255 in the IP address will allow any number. Example: 166.129.2.255 allows access by all IPs in the range 166.129.2.0166.129.2.255. Tip: ATF? will return a list of all the current Fn settings. Firewall Range You can define three different ranges of start and end.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 11.3.12 Port Forwarding Any data coming in on the defined Public Port will be passed to the corresponding Private Port connected to the physical interface specified and using the host IP address. Note: This feature can be used only in private mode. Note: There are no AT commands for Port Forwarding parameters, they need to be configured using AceManager.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual Host IP = d.d.d.d IP address of the connected device/computer. d.d.d.d = IP address Private Port = n Port number on the connected device. 11.4 n= 80 Logging This group includes commands specific to the internal log. Caution: Logging is intended for diagnostic purposes only. Extensive use of logging features can cause degraded modem performance.
Configuration Commands User Manual 11.5 RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Telemetry/Addr List Modbus, commonly used with telemetry devices, allows a connection via serial port to the modem. Telemetry and Addr List commands are only used when the modem is in one of the Modbus start-up modes. Further, Telemetry and the Addr List are available with all RLXIC Serial radios.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual MVOPT=n Modbus Variant Option: Sets various behavioral options when dealing with a Modbus-variant protocol. This parameter is used when the when MD is set to hex 63. Cannot be configured in AceManager. n=0 : No special action (Default). n=1 : Skip leading zeroes in Modbus packets. MVTYP=n Modbus Variant Type: The data-type of the RTU ID in a Modbus-variant protocol.
Configuration Commands User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM MLISTid=d.d.d.d Enters an ID and IP address into the Modbus List. ID is a decimal value (1 to 100). id=ID d.d.d.d=IP address or name MLISTXhexid=d.d.d.d Enters an ID and IP address into the Modbus List. ID is a hexadecimal value (0 to 64). 11.6 hexid=ID d.d.d.d=IP address or name Edge/HSDPA This group includes commands specific to HSDPA, EDGE and GPRS.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Configuration Commands User Manual +COPS=mode,[format][,oper] Manually specify an operator. Refer also to *NETOP. mode=0 : Automatic - any affiliated carrier [default]. mode=1 : Manual - use only the operator specified. mode=4 : Manual/Automatic - if manual selection fails, goes to automatic mode. format=0 : Alphanumeric ("name") (G3x10 must use this format).
Support, Service & Warranty User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 12 Support, Service & Warranty In This Chapter How to Contact Us: Technical Support................................................ 125 Return Material Authorization (RMA) Policies and Conditions............. 126 LIMITED WARRANTY......................................................................... 127 ProSoft Technology, Inc.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 12.2 Support, Service & Warranty User Manual Return Material Authorization (RMA) Policies and Conditions The following RMA Policies and Conditions (collectively, "RMA Policies") apply to any returned Product. These RMA Policies are subject to change by ProSoft without notice. For warranty information, see "Limited Warranty".
Support, Service & Warranty User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM c) If unit is repaired, charge to Customer will be 30% of current list price (USD) plus freight charges, duties and taxes as applicable. A new purchase order will be required or authorization to use the purchase order submitted for evaluation fee.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Support, Service & Warranty User Manual 12.3.
Support, Service & Warranty User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM c) The information in this Agreement is subject to change without notice. ProSoft shall not be liable for technical or editorial errors or omissions made herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of this material.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Support, Service & Warranty User Manual e) Customer agrees that it shall not, and shall not authorize others to, copy software provided by ProSoft (except as expressly permitted in any license agreement accompanying such software); transfer software to a third party separately from the Product; modify, alter, translate, decode, decompile, disassemble, reverse-engineer or otherwise attempt to derive the source c
Support, Service & Warranty User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM 12.3.8 No Other Warranties Unless modified in writing and signed by both parties, this Warranty is understood to be the complete and exclusive agreement between the parties, suspending all oral or written prior agreements and all other communications between the parties relating to the subject matter of this Warranty, including statements made by salesperson.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Page 132 of 136 Support, Service & Warranty User Manual ProSoft Technology, Inc.
Index User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Index $ $QCVAD=n • 101 & &Cn • 100 &Dn • 100 &Sn • 100 &V • 90 &W • 96 * *BOARDTEMP? • 91 *CSX1=n • 111 *CTSE=n • 101 *DATE=[mm/dd/yyyy],[hh mm ss] • 96 *DATZ=n • 114 *DBGCOMMLVL=n • 120 *DBGIPLVL=n • 120 *DBGPPPLVL=n • 120 *DEVICEID? • 89 *DHCPSERVER=n • 109 *DNSn=d.d.d.d • 106 *DNSUPDATE=n • 106 *DNSUSER=d.d.d.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM Application Interfaces • 14 Applying a Template to one modem with AceManager • 33 APPP • 100 ASLIP • 100 AT Commands • 38 AT Commands Requiring PassThru mode • 93 AT Mode • 53 B Bands • 13 Basic Modes • 51, 52 Basic Routing • 62 Before you start • 17 C Cellular Account Required • 17 Changing the USB port communication • 41 Choose a name and icon for your connection.
Index User Manual RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM IPL=n • 121 K Keepalive • 65 L LED Indicators • 14 Light Patterns • 26 Limitation of Liability • 2 Limitation of Remedies ** • 130 LIMITED WARRANTY • 127 Listening Port • 82 Logging • 120 M Management Information Base (MIB) • 81 MDhh • 105 Misc (Miscellaneous) • 93 MLISTid=d.d.d.d • 123 MLISTXhexid=d.d.d.
RLXIC-SG ♦ Intelligent Cellular RadioLinx Intelligent Cellular Serial Modem for Global GPRS/GSM SNMP Configuration • 82 SNMP MIB Definition Sample • 84 SNMP Traps • 81 Software Required • 17 Specifications • 13 Standards/Approvals • 14 Start AceManager • 19, 30 Start up Mode • 52 Status • 91 Steps of a connection: • 9 Supervisory Control and Data Acquisition (SCADA) • 74 Support, Service & Warranty • 125 Index User Manual Write the Settings to the RLXIC-SG • 21 X Xn • 100 Y Your Feedback Please • 3 Z Z