R STEREO RECEIVER AMPLIFIER RV2040 POWER PHONE AUTO FM/AM SCAN- SCAN+ A/B/C/D VOLUME - NO.
Voltage Votages are 230V AC,50Hz.
Getting Started 13.Unplug this apparatus during lighting storms or when unused for long periods of time. 14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way. Such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus. The apparatus has been exposed to rain or moisture. Does not operate normally or has bee dropped.
TABLES OF CONTENTS FIRST THING FIRST.................................................................................................. 2 UNPACK THE RECEIVER..................................................................................................... ABOUT REMOTE CONTROL ................................................................................................ BASIC CONNECTIONS.........................................................................................................
FIRST THINGS FIRST UNPACKING THE RECEIVER You should receiver the following items: One receiver unit One Remote Control VCR STEREO RECEIVER AMPLIFIER RV2040 CD POWER PHONE AUTO FM/AM SCAN- SCAN+ A/B/C/D VOLUME - NO.1-8 MEMORY INPUT VOLUME+ Indoor FM antenna One instruction book AM loop antenna R STEREO RECEIVER AMPLIFIER RV2040 POWER PHONE AUTO FM/AM SCAN- SCAN+ A/B/C/D VOLUME - NO.
FIRST THINGS FIRST ABOUT REMOTE CONTROL Remote controller operation range Installing batteries in the remote controller Since the remote controller will be used for many of this unit s control operations, you should begin by installing the supplied batteries. STEREO RECEIVER AMPLIFIER RV2040 1.Turn the remote controller over and slide the battery compartment cover in the direction of the arrow. POWER PHONE AUTO FM/AM SCAN- SCAN+ A/B/C/D VOLUME - NO.1-8 MEMORY INPUT VOLUME+ 2.
FIRST THINGS FIRST BASIC CONNECTIONS Assuming you have a DVD, the following steps will help you quickly set up your new receiver. If you have more electronic components, consult the table of contents or index for the page on which to find the connection description that best suits your situation. the wires(bought from store ) and jacks have been color-coded to assist you. 1.
FIRST THINGS FIRST CONNECTING THE SPEAKERS CONNECTING THE WIRES 1.Loosen the knob.2.Insert the bare wire.[Remove approx.5mm(1/4 ) insulation from the speaker wires]. 3.Tighten the knob and secure the wire. Or you also may use banana plug. Speaker Polarity When connecting the speakers, make sure the Method 1 polarities("+" speaker wire to "+" on the receiver) of speaker wires and terminals are matched. If the cords are reversed, the sound will be distorted and will lack bass("out of phase"effect).
FIRST THINGS FIRST CONNECTING FOR POWER Make sure you connect all your other electronic components and the speakers before plugging your receiver into the outlet. Plug the power cord in the wall outlet, matching the wide blade of the plug with the wide slot in the outlet. Be sure to insert the plug completely. USING HEADPHONES To listen privately through your audio system, use the PHONES jack on the receiver. How ever, make sure you turn down the volume before you put on the headphones.
RECEIVER CONTROLS & OPERATIONS 1 2 STEREO RECEIVER AMPLIFIER RV2040 3 4 5 6 7 8 9 10 11 12 GENERAL CONTROLS 1.Remote control sensor Receives signals from the remote controller. direction rotate the knob. 2.Display panel Display a variety of information. e.g. source etc. 8.A/B/C/D button Press the button to select a group of preset stations on the tuning status. 3.POWER switch Press this switch to turn on the power. Press the switch again to turn off the power. 9.
RECEIVER CONTROLS & OPERATIONS DISPLAY MESSAGES The following is an example of all the display messages you may encounter while using your receiver. Specific messages are referenced within the section(s) they apply. STEREO TUNED L R SLEEP MEMORY KH z MHz SLEEP STEREO Tuner stereo signal detected. Unit in Sleep mode KHz MHz TUNED Tuner station detected. Tuner frequency unit TUNING THE RECEIVER SELECT THE AM/FM BAND NOTE: 1.
RECEIVER CONTROLS & OPERATIONS Note: 4. Press MEMORY on the remote control. Weak signal can affect the "Automatic Preset Storing "MEMORY"will appear on the display. unction" efficiency. Adjust the antenna for the best reception for more efficient search 5. While the word "MEM" is still on, input your desired preset number(1-8)using the numeric STORING STATIONS IN MEMORY keys on the remote control to store the radio You can store up to 32 AM and FM stations, these station.
RECEIVER CONTROLS & OPERATIONS REMOTE CONTROLS 1. Input selector buttons Press these buttons to select a analog input source. 2.A/B/C/D button Press the button to select a group of preset stations. 3.BASS Parameter selector button VCR 9 Press the button to select bass tone. then press 1 CD 10 "8" buttons to adjust the low-frequency response. 4.TREBLE Parameter selector button Press the button to select treble tone. then press "8" buttons to adjust the high-frequency response. 2 11 3 12 5 13 5.
CONNECTING AUXILIARY COMPONENTS 1 2 3 4 R L ANTENNA FM AM COAX LOOP AUDIO INPUT VCR AUX STEREO RECEIVER AMPLIFIER MODEL NO.:RV2040 CD DVD REC OUT PRE OUT AMP IN L MADE IN CHINA AC INLET L R R VCR AUX CD 5 6 7 8 DVD REC OUT PRE OUT AMP IN R L 9 10 11 12 1.FM antenna input 2.AM antenna input 3.Right channel speaker output 4.Left channel speaker output 5.VCR Audio input jacks 6.AUX Audio input jacks 7.CD audio input jacks 8.DVD audio input jacks 9.
CONNECTING AUXILIARY COMPONENTS BEFORE YOU CONNECT..... of red and white. In this case, the black plug takes the place of the white plug. CONNECTING THE CABLES -Protect components from power surges. -Connect all components before plugging power cords into the wall outlet. -Always turns off the receiver and/or components before you connect or disconnect any cables. -Always make sure the color-coded plugs match the colour of the terminals in which they are inserted.
CARE AND MAINTENANCE TROUBLESHOOTING TIPS RECEIVER/TUNER OPERATION GENERAL STEREO indicator is off. No audio -Adjust the antenna. -Make sure the MUTE indicator on the front panel -The signal is too weak. Connect an external is off. -Make sure the speakers are turned on. antenna. -The signal is Mono. -Check the connections. -Sever hum or noise. -Check the short plug between PRE OUT jacks -The signal is too weak. Connect an external and AMP IN on the rear panel is inserted.
EQUIPMENT SPECIFICATIONS AMPLIFIER SECTION Left & Right Channel......................................................................................................2X100Watts Signal to Noise(A weight)..........................................................................................................85dB Frequency Response......................................................................................20Hz-20 KHz+/-1.5 dB AM TUNER SECTION Frequency Response......................................
R RV2040 STEREO RECEIVER AMPLIFIER
