Owner manual

ManualsBrandsProTemp ManualsFansPT-48-BDF-A

This product meets and exceeds the requirements of OSHA 1910.212(a)(5), the standard which

regulates electric fan blade safety, and is certified under UL# E234000, established and made

effective April 10, 2003, and updated March 23, 2005, by Underwriters Laboratories, Inc.

Please note the serial number of your fan, and write it on the back of this User’s Manual for future reference. Your serial

number is located on upper rear section of mount bar.

READ AND SAVE THESE INSTRUCTIONS

Model Numbers: PT-36-BDF-A, PT-42-BDF-A, PT-48-BDF-A

User’s Manual and

Operating Instructions

668 Stony Hill Road #302 Yardley, PA 19067 USA Toll Free: (800) 641-6996

Fax: (215) 891-8461 • Web: www.pinnacleint.com • Email: info@pinnacleint.com

900450100-12

IMPORTANT: Read and understand all of the directions in this manual before assembling,

starting, or servicing the fan. Improper use of this fan can cause serious injury. Keep this manual for

future reference.

For ventilating use only. Do not use to exhaust hazardous chemicals or use near

any flammable liquids or gases as sparks from motor may ignite fumes. Never use

the fan in spaces which contain products such as gasoline, solvents, paint thinners, dust particles,

volatile or airborne combustibles, or any unknown chemicals.

WARNING

Summary of content (8 pages)

PAGE 1
User’s Manual and Operating Instructions Model Numbers: PT-36-BDF-A, PT-42-BDF-A, PT-48-BDF-A READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the directions in this manual before assembling, starting, or servicing the fan. Improper use of this fan can cause serious injury. Keep this manual for future reference. WARNING For ventilating use only. Do not use to exhaust hazardous chemicals or use near any flammable liquids or gases as sparks from motor may ignite fumes.
PAGE 2
NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A POWER SOURCE Table of Contents Safety Information.............................................. 2 Installation ...................................................... 3 Operation ...................................................... 3 Belt Maintenance............................................... 3 Maintenance and Storage .................................. 4 Wiring Diagram .................................................
PAGE 3
NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A POWER SOURCE Installation Simply locate fan in safe, desired position on level ground, fold out wheels, and connect to approved power source. NOTE: This fan uses a folding wheel design. For quick assembly, simply swing the wheels out and snap to lock in place ( see figure 1). Swing UP to lock Swing out wheels figure 1: Wheel Assembly Operation NOTE: This fan is equipped with a 2-speed control switch. 5.
PAGE 4
NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A POWER SOURCE Belt Tightening / Replacement 1. Remove screws from Rear Guard and tilt wheel (figure 2). 3. Remove belt to replace, or adjust motor to tighten belt (figure 3). 2. Loosen motor nuts, and motor safeguards (located above and below motor). figure 3: Adjusting Fan Belt figure 2: Removing Guard Maintenance and Storage 1. Inspect your fan before each use.
PAGE 5
NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A POWER SOURCE Troubleshooting Guide Problem Fan does not operate Reduced Air Flow Excess Noise (vibration, slapping, squealing) Possible Cause Corrective Action 1. No power Inspect Power Cord for damage. Be sure unit is plugged in and turned on. 2. Bad switch Replace Power Switch (Note: To prolong life of Power Switch, it is recommended that the fan is first operated in LOW for 510 seconds before switching to HIGH). 3.
PAGE 6
NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A POWER SOURCE Replacement Parts Models: Item # Description PT-36-BDF-A PT-42-BDF-A PT-48-BDF-A 90-032-0005 90-032-0005 90-032-0005 N/A N/A N/A 1 Hardware for Guards 2 Front Guard 3 Fan Blade Assembly 90-003-1025 90-003-2025 90-003-5225 4 Power Switch Holder 90-016-0100 90-016-0100 90-016-0100 5 Capacitor 90-004-0100 90-004-0100 90-004-2500 6 Power Switch 90-025-0100 90-025-0100 90-025-0110 7 Handle / Cor
PAGE 7
NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A POWER SOURCE 16 22 21 1 2 3 26 4 25 5 6 24 7 23 8 9 10 20 17 18 15 11 14 13 19 12 Exploded View figure 7: Exploded View © 2011, Pinnacle Products International, Inc.
PAGE 8
NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A POWER SOURCE 1 YEAR LIMITED WARRANTY PINNACLE PRODUCTS INTERNATIONAL, INC. WARRANTS THIS PRODUCT TO THE ORIGINAL RETAIL PURCHASER ONLY, TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR FROM THE DATE OF INITIAL PURCHASE. THIS PRODUCT MUST BE PROPERLY INSTALLED, MAINTAINED AND OPERATED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED. PINNACLE PRODUCTS INTERNATIONAL, INC.