Operation Manual

ManualsBrandsProteus ManualsExercise BikeBC-81090 Monitor

PROGRAMMABLE MAGNETIC EXERBIKE

MONITOR BC-81090 WITH LCD DISPLAY

SUMMARY:

This system is designed for programmable magnetic bike. There are 3 parts to this system the monitor

(BC-81090), motor & controller and magnetic braking system.

A. Power up :

1. Before all, you should connect the connection cables with monitor together.

2. The power supplier to the monitor is 6V/500mA. Please make sure the output of the adaptor is

correct.

3. After power up, all LCD segments will light up for 2 seconds & CPU will be reset the resistance

into level 1. And then the system goes to the clock and date setting mode. After finished the clock

and date setting or without setting any value after 20 seconds, the monitor will goes into the

initial mode. The displays will be shown as fig. 2.

**REMARK:

DO NOT CONNECT ANY ( AC, DC ) POWER SUPPLY

BEFORE COMPLETELY ASSEMBLED

1. If the connection cables were installed incorrectly, monitor will display “E1” on matrix display

and generate a beep sound. To release the beep sound, please press “ START / PAUSE (Hold to

reset) “ button or take off the adaptor. Before asking service, please examine if all connection

cables are well connected, and without broken.

2. Using a period of time, if the power source can’t drive the motor and controller smoothly, the

monitor will display a sign of “E1”. Unplug the adaptor and wait for 15 seconds, and then reinstall

the plug of adaptor. If the monitor still shows “E1” and beeps, please call service man.

3. If the monitor shows “ E2 ”message, please call service man.

Summary of content (4 pages)

PAGE 1
PROGRAMMABLE MAGNETIC EXERBIKE MONITOR BC-81090 WITH LCD DISPLAY SUMMARY: This system is designed for programmable magnetic bike. There are 3 parts to this system the monitor (BC-81090), motor & controller and magnetic braking system. A. Power up : 1. Before all, you should connect the connection cables with monitor together. 2. The power supplier to the monitor is 6V/500mA. Please make sure the output of the adaptor is correct. 3.
PAGE 2
B. Clock and Date Setting: 1. After power on the monitor, the top of the LCD will display “ PM 12:00 00 01D01M03Y” and the hour display will flash. 2. Press ♁ or \ button to set up the hour value and then press the ENTER button to confirm your setting value. 3. Minute display will flash. Press ♁ or \ button to set up the minute value and then press the ENTER button to confirm your setting value. 4. The Letter of E will flash. It is means the language is English.
PAGE 3
displayed on the graphic LCD. c. After finished program setting, press ENTER key to enter Time setting. d. The press ♁ or \ key to set up your desirous workout time. e. After finished time setting, press ENTER to exit or press START key to start exercising. f. When start exercising, your present workout interval will be flashing in rate of 0.5 second on & 0.5 second off. g. During exercising you can press ♁ or \ key to increase or decrease your workout resistance freely. h.
PAGE 4
FUNCTIONS DISPLAY VALUE TIME (Display the elapsed time.) 00:00 ~ 99:59 (COUNT UP) 05:00 ~ 99:00 (COUNT DOWN) SPEED (Display the current speed.) 0.0 ~ 99.9 KPH (or MPH) DISTANCE (Display the trip distance.) 0.0 ~ 999.9 Km (or Mile) RPM (Display the revolutions per minute.) 0 ~ 999 CALORIE (Display the calorie consumption.) 0.0 ~ 99.9 ~ 100 ~ 999 Kcal PERFORMANCE VALUE 0 ~ 999 AGE (Input your age.) 1 ~ 99 PULSE (Display the heart rate in beats per minute.) 40 ~ 240 F.