Testing specification : EN 957-1, EN 957-6. he GS Mark is a voluntary 3rd party inspection and certification scheme for finished products only, .. according to German Equipment Safety Law - Geratesicherheits - Gesetz. This label ensures products strictly meet the technical safetyrequirements as stipulated by the GSG and the current production line is audited. Features of product with GS-TUV mark : Mechanical and electrical safety. Symbol of high quality. Reliability assurance.
Index INDEX . . . . . . . . Introduction / Safety Guideline . . . . . . . . . . . . . . . . . . . . Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exploded Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction / Safety guideline 01 1 INTRODUCTION Thank you very much for choosing PROTEUS products. To secure the safety, pls read the manual and all suggestions carefully before using the product. While you get everything ready, believe that you could enjoy the pleasure of exercise and healthy. 2. SAFETY GUIDELINE * Before starting any exercise program consult your Physician. * Read this users manual and follow the instructions. * Do not allow children to play on the treadmill.
MAINTENANCE : a. Maintenance 1. Clean and lubricate the bed of the treadmill every 20 hours of use or monthly, which ever comes first ( SEE TREADMILL LUBRICATION INSTRUCTIONS ). Daily cleaning to the sides of the running mat will prevent much of the dirt from getting underneath the mat. 2. Prevent the build up of dust beneath the motor cover and under the treadmill body ( any work involving the removal of the motor cover should be carried out by a qualified technician ).
Maintenance 6. Mat slippage may be occurred for a short time. If it persists, adjust the running mat tension as per direction in the owner's manual ( adjust belt tension ). Do not over-tighten, as this will decrease the life of the mat and place undue stress upon the roller bearings. 7. If you are uncertain of any procedure or lack of correct tools, please contact your dealer. We recommend a qualified technician carry out work involving removal of the motor cover. 03 ( clean ) ( instruction ) c.
Information 4¡E INFORMATION¡GLDT-8850 Basic spec : Machine size 190 x 85 x 159cm Electric spec AC 110V 60Hz / 220V50Hz Folded size 113 x 85 x 159cm Speed range 1km/h ~ 18 km/h Running surface 50 x 140cm Motor 2.5HP 4000RPM Thickness of running belt 1.8mm Thickness of running deck 25.4mm Machine base section Square tube(40x80) Elevation type Elevation motor ( stepless/16 levels ) Upright tube section Square tube(40x80) Elevation angle 0°~5.5° Painting Black powder-body Max.
Parts List 05 LDT-8850 PARTS LIST No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Description Main frame Cushion Square tube cap Foot unit Front roller set Rear roller set Motor V- belt M8 screw M8 washer Semicircle Hex. screw Air Pressure shaft Under cover for rear roller ( L ) Under cover for rear roller ( R ) Top cover for rear roller ( L ) Top cover fro read roller ( R ) Washer Round-headed screw Running board Q'ty 1 8 6 2 1 1 1 1 4 8 3 2 1 1 1 1 52 6 1 No.
Parts List No. 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Description Handlebar cover ( inside, right ) Handlebar cover ( outside, right ) Big flat spider screw Top handle bar Hex. Screw Control board Wave filter Inductor Elevation motor Power socket Thermo switch Power switch Base assembly Wheel Semicircle Hex. Screw Nut jacket Console combined plate Round-headed spider screw Console assembly Q'ty 1 1 6 1 2 1 1 1 1 1 1 1 1 4 11 2 2 4 1 No.
Parts List 07 No. 77 78 79 80 81 82 83 84 A B C D E F Description Washer Spring washer Semicircle Hex.
17 61 22 62 17 17 60 57 58 23 40 73 81 70 21 55 56 19 38 39 33 24 79 42 41 10 43 54 58 45 17 20 17 32 46 34 34 67 65 68 1 76 53 34 69 72 2 16 48 49 35 64 66 47 75 80 74 36 08 36 44 17 37 82 Exploded Drawing 71 59 14 50 30 15 72 31 72 78 28 63 51 52 34 77 3 4 18 77 25 72 36 12 84 11 10 35 29 13 83 17 7 26 27 8 9 5 6 77 11 11 17
Parts List c Accessories 1 2 Description Handle bar cover (R) Handle bar cover (L) Unit set set Q'ty 1 1 Part no. 39 / 40 37 / 38 Unit pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs Q'ty 6 8 2 6 2 10 2 1 2 1 Part no. 35 58 36 41 43 10 54 d Parts box / tools 09 1 2 3 4 5 6 7 8 9 10 Description Semicircle Hex. screw Semicircle Hex. Washer Semicircle Hex. screw Big flat screw Hex. screw Washer (black) Nut jacket T-type wrench Hex.
Assembly - Base 5 Assembly a Note: DO NOT FULLY TIGHTEN ALL FASTENERS UNTIL ASSEMBLY IS DONE. DO NOT PLUG IN POWER SUPPLY UNTIL ASSEMBLY IS COMPLETED. DO MAKE SURE ALL FASTENERS WELL TIGHTENED BEFORE USE. b Machine base Locate the main frame ( 1 ) on level floor, then adjust foot unit ( 4 ) to attach the floor. This could steady the machine without causing wobble. Method of adjusting foot unit 1. Use wrench to loose upper nut, then adjust lower screw. 2. Turn right, then foot unit on the rise. 3.
Upright Tube Assembly c Upright tube assembly Put 33 upright tube unit ( right ) besides the main frame, connect the frame control wire (A) ( 5-pins ) onto upright tube control wire (A) ( 5 -pins ), then connect elevation wire (B) ( 3-pin ) onto elevation control wire (B) ( 3-pin ) on upright tube unit ( right ).
65 66 12 12 51 *** CAUTION *** While the frame been moved to exceed top position, It is heavy and without any support. Pls hold it very carefully. Strongly suggest to assemble this machine with two persons. After assembled the air pressure shaft, suggest it to upright very top position, then lay the machine to horizontal position.
Assembly - Monitor e. Monitor Put top handlebar ( 42 ) into upright tube unit ( 32,33 ), with screw ( 43 ) and washer ( 10 ) pre-fix onto upright tube unit ( 33 ) but not fully fastened then put the other side with screw ( 43 ) and washer ( 10 ) pre-fixed onto upright tube unit ( 32 ). ( whatever one end of screw could not be touched, push the upright tube unit ( 32,33 ) inward to make screw touch the nut ). Put the screws on, after fixing both end screws, not fully fasten while fixing.
Assembly - Cover f Cover Put right handle bar cover ( 39,40 ) onto upright tube assembly ( right ,33 ), tighten firmly with screw ( 41 ). Put left handle bar cover ( 37, 38 ) onto upright tube ( left, 32 ), tighten firmly with screw ( 41 ). 40 39 41 33 14 38 41 37 32 g Final adjustment Press monitor to upright tube unit ( left and right ) to close together with outside handle bar cover. Then fasten all the screws firmly.
Folding 6 Folding and unfolding : CAUTION : Before folding and unfolding, the safety key should be pulled away and the spring pin lock into support shaft. 1 Folding Pull spring pin ( 66 ) out, hold the end machine, folding the machine up till the spring pin lock into support shaft. ( there is click sound ). *** CAUTION *** The elevation motor should be at horizontal position while folding.
Adjust the machine a Adjust belt tension FACTORS THAT AFFECT MAT ALIGNMENT. 1. The treadmill must be on a level surface. 2. While user running with an uneven stride, the mat should return to center after exercise. 3. Maintain the correct mat tension. In principle, the belt was adjusted by the belt adjusting screw in the back of the machine, if need to adjust the roller, do not adjust the roller by yourself. Pls ask distributor for help.
Mat alignment b MAT ALIGNMENT NOTE : THE ALIGNMENT OF THE TREADMILL MAT MUST BE CORRECTLY ADJUSTED TO ENSURE SMOOTH OPERATION AND TO PREVENT DAMAGE. The treadmill mat must run close to the central position of the treadmill. If the gaps between the mat and the side panel are different, the mat must be aligned. 17 SET THE SPEED OF THE MACHINE AT 4 - 6 km/h, IF THE TREADMILL MAT HAS MOVED TO THE LEFT HAND SIDE, 1. Turn the left mat adjustment bolt clockwise 1/2 a turn. 2.
Incline c Incline To increase incline: press incline switch To decrease incline: press incline switch to incline level. to decline level. Note : Incline device used over 5 minutes continuously, need off for 20 minutes, to avoid incline device damaged due to overheat. d Instruction of Safety key and pulse The machine works only the safety key ( 62 ) attached to the monitor ( 61 ). For safety purpose, pull out the safety key while not using the machine.
Pulse *** While using hand pulse, the hands should be without too much moisture, so dry your hands before doing exercise. Otherwise, it will affect the accuraey of heart rate. Also, while using pulse, user should leave running belt and stand at safe area. PROTEUS had done the best efforts to let customers understanding all the operations and functions before printing this manual.
LDT-8850 Monitor LDT-8850 MONITOR 20 The monitor, is designed for motorized treadmills and introduced in the following categories, * Key Functions * About Displays * Operation Instructions * Error Massage & Troubleshooting
Monitor Functions 21 KEY FUNCTION : There are total 16 buttons including 1 Safety key, 9 Major Function buttons, and 6 quick speed buttons. A. Safety Key : The monitor and the treadmill can be operated only with the key attached and note both of the monitor and the treadmill stop as soon as the key is removed. B. Nine Major Function Keys : a. WARM UP : This is a 5 minutes program. In the stop status, press this button to enter the Warm UP program.
c. ENTER / REST / PULSE RECOVERY : ENTER FUNCTION : 1. During the stop mode, press this button to confirm your desired program from Manual, P1, P2, P3, P4, P5, P6, P7, P8, P9, U1, U2, 60% MAX H.R., and 85% MAX H.R. 2. During the setting mode, press this button to confirm your setting value of time, distance, calorie, target heart rate and the minimum speed in the P1 to P9. 3. During creating the speed profile, press this button to confirm your SPEED PROFILE in the U1 and U2. RESET FUNCTION : 1.
Monitor Functions 23 d. MODE : 1. Press this button to choose the function from Manual, P1, P2, P3, P4, P5, P6, P7, P8, P9, U1, U2, 60% MAX H.R., and 85% MAX H.R. LED DISPLAY e. SPEED ¡¶ : 1. In preset status, press this button to increase the setting value of time, distance, calorie, target heart rate and the minimum speed in the P1 to P9. 2. In the starting status, press this button once to increase 0.5 KPH or 0.1MPH. To speed up the increment, hold this button for more than 2 seconds. 3.
Monitor Functions f. INCLINE : Press this button to increased the level of elevation. INCLINE : Press this button to decrease the level of elevation. g. COOL DOWN : In the start status, press this button to enter the COOL DOWN function. After press this button, the elevation system will go to level 0 and cool down function will begin to work. This is a 5 minutes program, so time will count down from 5:00 to 0:00. We strongly recommend using the cool down function before you wish to stop exercise.
Monitor Functions QUICK SPEED : There are 6 speed buttons on the monitor. During the start mode, press the QUICK SPEED button in any time and the motorized treadmill will change the speed immediately to the speed you desired. speed was selected by you. Note : The QUICK SPEED buttons cannot use in the Warm Up and Cool Down program.
About Display ABOUT DISPLAY : A. PROGRAM AND MANUAL PROFILE DISPLAY : Display the profile of Manual, P1, P2, P3, P4, P5, P6, P7, P8, P9, U1, U2, 60% MAX H.R., and 85% MAX. The profiles in Manual, P1, P2, P3, P4, P5, U1, and U2 are speed profiles. The profiles in P6, P7, P8, P9, 60% MAX H.R., and 85% MAX H.R. are incline profiles. The profile was composed by 20 intervals. Without setting the time value, each column will retain 30 seconds.
About Display 27 C. DISTANCE Display : Shows the distance with counting up or down. In the setting mode, press SPEED or SPEED button to set the desired distance to do the exercise. The range of setting value is from 1.00 KM to 999 KM. By set the value, the distance value will count down. While counting down to 0.00, the monitor will beep and then the treadmill will stop. Without setting value, the distance will count up and the range of distance value is 0.00KM to 999 KM. x2 D.
x4 F. PULSE & INCLINE Display : During the setting stage : a. In the Manual, P1, P2, P3, P4, P5, P6, P7, P8, P9, U1 and U2 program, while the program window show ENTER TARGET HEART RATE , press SPEED or SPEED button to setting the desired target heart rate that you do not want to exceed this value during your exercise. Once your heart rate is more than your setting value, the monitor will glitter to inform you. x5 About Display E. SPEED Display : a.
About Display 29 b. In the 60% MAX H.R. and 85% MAX H.R program, while the program window show ENTER AGE press SPEED or SPEED button to setting your age. And then the program window will display ENTER H/R TARGET The window will show the target heart rate value. If you accept this value, press ENTER and go to next setting value. If you can not accept this value, press SPEED or SPEED button to setting the desired target heart rate that you do not want to exceed this value during your exercise.
LED DISPLAY Operation Instructions OPERATION INSTRUCTIONS TO START : Turn on the power and attach the Safety Key to the monitor. And all the windows will fully display for one second; the program will start from manual function. Press the start/stop button to begin excercise. Notice that the machine does not work without the Safety Key attached. ON POWER SWITCH 30 TO STOP : Press the start/stop button. Or remove Safety Key or turn off power switch.
Operation Instructions CAUTION : Please clip the other end of the Safety Key to user's clothing before exercising to ensure the machine will stop in case the user accidentally runs off the treadmill. Should that happens, the Safety Key will fall off from the monitor and the treadmill will stop at once to avoid further injury. CLOTHES 31 QUICK START : a. Press the mode button to select one of the programs from Manual, P1, P2, P3, P4, P5, P6, P7, P8, P9, U1, and U2. b. Press Start button to begin exercise.
LED DISPLAY b. TIME window will glitter. Press the SPEED or SPEED exercise. Press ENTER to confirm the value of TIME, to set up the desired time to do the c. DISTANCE window will glitter. Press SPEED or SPEED button to set up the desired distance for exercise. Press ENTER to confirm the setting value of DISTANCE, Operation Instructions -- MANUAL FUNCTION-a. Attach the Safety Key to the monitor. And all the windows will fully display for one second; the program will go to the Manual(M) function.
Operation Instructions d. CALORIES window will glitter.Press SPEED or SPEED button to set up the desired CALORIES to be burned. Press ENTER to confirm the setting value of CALORIES. e. The SPEED window will glitter. Press SPEED or SPEED button to choose the Difficulty of this SPEED profile. Press the ENTER to confirm your desired speed profile. 33 f. And then the PULSE window will glitter and the PROGRAM PROFILE window will show ENTER TARGET HEART RATE .
or SPEED or If you want to skip the setting function, just simply press ENTER to go to the next preset function. You do not need to set up all of these functions before exercise. You can just choose one of them or two of them. Note : a. Without setting the function of TIME, DISTANCE and CALORIE, the monitor will count up the value. b. Without setting the function of Speed ( Difficulty ), the motorized treadmill will follow our initial speed profile. c.
Program Function 35 -- PROGRAM FUNCTION P1 TO P9 -a. Press the mode button to select one of the Preset programs from P1 to P9. b. Press the Enter button. c. TIME window will glitter. Press the SPEED or SPEED to set up the desired time to exercise. d. Press ENTER to confirm the value of TIME, and then DISTANCE window will glitter. e. Press SPEED or SPEED button to set up the desired distance to exercise. f. Press ENTER to confirm the setting value of DISTANCE, and then CALORIES window will glitter. g.
Note : a. Without setting the function of TIME, DISTANCE and CALORIE, the monitor will count up the value. b. Without setting the function of Difficulty, the motorized treadmill will follow our initial speed or incline profile to do. c. Without setting the function of TARGET HEART RATE, the monitor will not give you the feed back from your heart rate. Monitor displays your current heart rate only. Program Function the profile will not change anymore even you press the SPEED button.
Program Function 37 d. Once reach your target, the motorized treadmill will beep and then stop. You can press START again to reach you next target. The original target your reached will become count up. The other targets you do not reach will continue count down. -- USER SETTING PROGRAM ( U1 U2 ) -a. Press the mode button to select one of the users setting program from U1 to U2. b. Press ENTER button. c. TIME window glitter, user SPEED or SPEED to set up the desire TIME to exercise. d.
or SPEED or If you want to skip the setting function, just simply press ENTER to go to the next preset function. You do not need to set up all of these functions before exercise. You can just choose one or two of them. Note : a. The monitor only stores the speed profile and will not keep the data of preset values, Time, Distance, Calorie and Target heart rate, for use. b. Without setting the function of TIME, DISTANCE and CALORIE, the monitor will count up the value. c.
Program Function 39 -- HEART RATE CONTROL PROGRAM -a. Press the mode button to select one of heart rate control programs ( 60% MAX H.R., and 85% MAX H.R ). b. The PROGRAM PROFILE will display ENTER AGE and the PULSE window will flash. The number indicate is Age and the initial value of Age is 25 years old. The range of Age is from 10 to 99 years old. c. Press SPEED or SPEED button to key in your age. d. Press ENTER to confirm your age. e.
Program Function Monitor will compare your heart rate and target every 30 seconds. If your actual heart rate is 5 b.p.m. below the target, the elevation will increase 1 level. If your actual heart rate is 5 b.p.m. or more above the target, the elevation will decrease 1 level. If the monitor do not receiver your heart rate signal, the monitor will display every 30 seconds to remind you and the treadmill will keep the same elevation level.
Program Profile PROGRAM PROFILE ( Unit = Km / Hr ) P1 P4 18 (KM/H) 14 12 10 8 6 4 2 P2 P5 18 (KM/H) 14 12 10 8 6 4 2 41 P7 18 (KM/H) 14 12 10 8 6 4 2 P3 P8 18 (KM/H) 14 12 10 8 6 4 2 P6 18 (KM/H) 14 12 10 8 6 4 2 18 (LEVEL) 14 12 10 8 6 4 2 18 (LEVEL) 14 12 10 8 6 4 2 P9 18 (LEVEL) 14 12 10 8 6 4 2 18 (LEVEL) 14 12 10 8 6 4 2
Program Profile ERROR MASSAGE & TROUBLESHOOTING E1 : It indicates no signal picked up for 15 seconds and the monitor stops. Solutions : pls consult Dealer. E2 : It indicates the problems of EEPROM IC chip. Either the ID code is incorrect or the data accessed from the IC chip is wrong. Solutions : pls consult Dealer. E3 : It indicates that VR value is not change by 5 seconds. Solutions: a. Check the relay ( 12MBU-5 ), which controls the INC. The relay clicks while it is functioning well.
Warm - Up WARM - UP GUIDELINES Warming up is an important part of every workout. Warming up prepares the body for more strenuous exercise by increase circulation, deliver more oxygen to the muscles, and raise the body temperature. SUGGESTED STRETCHES The following stretches provide a good warm-up, or cool-down. Move slowly as you stretch-never bounce. 43 HAM STRING STRETCH Sit with one leg extended. Bring the sole of the opposite foot toward you, resting it against the extended leg's inner thigh.
Warm - Up TOE TOUCHES Standing with your knees bend slightly, slowly bend forward from the hips. Allow your back and shoulders to relax as you stretch down toward your toes. Go as far as you can and hold for 15 counts, then relax. Repeat three times. Stretches : Hamstrings, Back of Knees, Back QUADRICEPS STRETCH With one hand against a wall for balance, reach behind you and pull up your foot. Bring your heel as close to your buttocks as possible. Hold for 15 counts. Repeat.
