PRODUCT MANUAL CONTRACTOR MITER SAW WORK STATION WS-077 1
OVERVIEW You have just purchased a Contractor Work Station. This product has been specifically designed to assist you in the use of your 10-12" miter saw, as well as increasing efficiency with other bench top tools such as table saws, band saws, planers, etc. SAFETY WARNING WARNING: Be sure to read and understand all safety instructions in this manual, including all safety alert symbols such as “DANGER”, “WARNING” and “CAUTION”, before using this power tool accessory.
13. Never stand or sit on tools. Material Support 14. Replace damaged components immediately. 15. Make sure your work platform is sufficiently sturdy to do the specific job at hand. 16. Think safety. Safety is a combination of operator awareness, common sense and alertness at all times.
SAFETY INSTRUCTIONS FOR MITER SAW STANDS 1. Use caution when folding or unfolding legs to limit any finger pinch points. 2. Place stand on flat and level surface to keep from rocking or tipping. 3. Make sure that work support extensions (if included) are within safe operating limits, and are properly locked in place before using tool. Do not exceed the rated capacity on main frame table. 4. Test the setup for stability before proceeding with work. 5.
ATTACHING THE AXLE PLATE See Figure 4 1. Place (2) M8*20 bolts through the holes in the axle plate. Washer Spring Washer FIG 4 2. Place the axle plate onto the end of the miter saw stand making sure that the bolt runs through the holes on the miter saw stand. Nut 3. Place the washer and spring washer over each bolt on the back side of the miter saw stand. 4. Lift the miter saw stand to an upright position. 5. Tighten M8 nut over the washer until secure. ATTACHING THE PULL HANDLE See Figure 5 1.
ASSEMBLING AND INSTALLING MATERIAL WORK SUPPORTS FIG 7 See Figure 7 1. Slide a carriage bolt (M6 x 55mm) through the square hole in the work support and extend through the other side. 2. Place the work stop over the end of the bolt. 3. Thread a knob nut M6 (Part #12) over the end of the bolt and tighten to secure. 4. Slide the work support rail through the hole in the top of the work support mounting bracket. Knob Nut M6 5.
1. Unplug the saw and lock the saw arm in the down position. 2. Place a tool mount underneath the saw, aligning the mounting holes on the miter saw base with the slot in the top of the tool mount. FIG 8 3. Feed a carriage bolt up through both the tool mount and a mounting hole in the saw. 4. Secure in place using a flat washer, spring washer, and nut. 5. Repeat through the other end of the tool mount. 6.
MOUNTING THE MITER SAW TO THE STAND See Figure 10 Use the handles located at the rear of the tool mounts to aid in installing or removing saw and tool mount assembly. 1. Lift the saw and tool mount assembly, allowing the assembly to tilt slightly toward your body. 2. While still tilted toward you, hook the front edge of the tool mount assembly onto the front rail of the stand. FIG 10 3. Lower the tool mount assembly to allow the rear edge of the tool mount to seat fully over the rear rail. 4.
TRANSPORTING AND STORING See Figure 12 1. Before storing or transporting, make sure all attachments are secure and bench top tool is removed. 2. Collapse legs and make sure they are locked into the up position. 3. Use the handle that is located on the end of the product for transporting. 4. Pull up on the handle and tilt workstation until weight is distributed evenly onto wheels. TOOL MOUNT ADJUSTMENT SCREW FIG 12 Most plastic tool mounts are designed to fit snugly over the stand rails.
GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. LIFETIME LIMITED WARRANTY PROTOCOL™ Contractor Miter Saw Work Station is backed by a Limited Lifetime Warranty. This warranty covers manufacturer defects and workmanship. The warranty excludes misuse or abuse and normal wear and tear.
