XEROX XAP User's Guide 290.00 mm 145.00 mm User ' s Guide XAP Series 210.00 mm LCD Monitor XA7-17i XA7-19i PANTONE Process Black CV PANTONE Red 032 CV 1.
©2005 by Xerox Corporation. All rights reserved. Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as icons, screen displays, looks, etc. XEROX® and all Xerox product names mentioned in this publication are trademarks of XEROX CORPORATION.
Table of Contents CE Marking Declaration Of Conformity .................................................4 Federal Communications Commission (FCC) Statement ....................5 Important Safety Instructions.................................................................6 1 Introduction Features ........................................................................................................9 Package Contents .......................................................................................
RECYCLING PLACE ENGLISH Recycling Place EUROPE When disposing of Proview products in Europe, please contact one of the following three locations to make arrangements for recycling. Proview International (UK) Limited 30 The Avenue, Watford, Hertfordshire WD17 4AE United Kingdom Timothy Lo Tel: +44 1923-248-111 Fax: +44 1923-248-222 Email: tim.lo@proview.co.uk PGL Europe B.V.
FCC/CE CE Marking Declaration Of Conformity This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/EEC “Low Voltage Directive” as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
FCC/CE ENGLISH Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits of a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Important Safety Instructions Important Safety Instructions To prevent any injuries, the following safety precautions should be observed in the installation, use, servicing and maintenance of this equipment. Before operating this equipment, please read this manual completely, and keep it nearby for future reference. Warnings • Do not place the equipment on any uneven or unstable carts, stands, tables, shelves etc.
Important Safety Instructions ENGLISH • Do not touch the power cord and antenna cable during lightning. • Remove the plug from the wall outlet if the equipment will not be used for a long period of time. • Do not place, use or handle this equipment near water. • Never expose the equipment to liquid, rain, or moisture. Seek qualified service if any of the above is spilled into the equipment. • Do not attempt to service the equipment yourself.
Important Safety Instructions • If any of the following conditions occur, unplug the power cord from the outlet and request service from qualified personnel. a. The power cord or plug is damaged. b. Liquid is spilled into the product . c. An object falls onto or into the product. d. The product has been dropped or damaged. e. The product’s display is abnormal.
Introduction Features i-Reflection Wider View Angle er View Angle raLive tand Move ENGLISH 1 Introduction xTraSharp xTraMove xTraColor xTraLive xShield DTTV Xtouch buttons xStand xTraSharp xTraMove xStand xShield Anti-Reflection • Adjustable Ergonomic Xstand This stand is versatile for users to make any adjustment Xtouch buttons DVI comfortable for use. Besides the existing VESA mount ability, users can tilt, swivel, pivot and adjust the height of the monitor.
Introduction Package Contents Make sure all of the following contents are included in the box. If any items are missing, please return this product to the original place of purchase. LCD Monitor DVI-I to D-SUB Adapter Quick Guide Warranty Card CD-ROM (Driver/Manual) Power Cord* * Power cord specification : H05 VV-F 3G 0.75mm2 CAUTION: Be sure to save original box and all packing material for future transport of monitor.
Introduction ENGLISH Front View and Controls 1 2 4 3 5 1 MENU Press once to display the OSD (On Screen Display). And press to activate the items you highlight . 2 DOWN/UP In OSD mode, press the DOWN/UP buttons to move the selection highlight to the next menu item counterclockwise or clockwise, respectively. Adjusts the volume up and down. 3 AUTO Press to automatically adjust the display settings to optimize performance based on the D-SUB signal.
Installation 2 Installation Refer to the owner’s manual of the computer for connections. In the process of connecting external equipment, do not connect any AC power cords to wall outlets until all other connections are completed. Connecting Your LCD Monitor to a Computer Method 1: Analog (D-SUB) Connection 1 2 3 4 Turn off the computer and unplug the power cable. Fit the DVI-I to D-SUB adapter onto the signal cable of the LCD monitor.
Installation 6 Connect the power cord to wall outlet and LCD monitor. Press the POWER button, located on the bottom side of the main unit to turn the monitor on, then turn the computer on. If the monitor displays an image, the monitor is successfully installed. If no image is displayed, check all connections. 5 Connect to power source NOTE: Unplug the monitor before installation to avoid electric shock or damage.
Installation Method 2: Digital (DVI) Connection 1 2 3 4 5 Turn off the computer and unplug the power cable. Connect the signal cable (DVI-I) to the DVI port on the back of the computer. Connect the audio cable to the line-in port on the back of the computer. Connect the power cord to wall outlet and LCD monitor. Press the POWER button, located on the bottom side of the main unit to turn the monitor on, then turn the computer on. If the monitor displays an image, the monitor is successfully installed.
Installation • • Press the MENU button to display the OSD. Press the UP or DOWN button to highlight the (INPUT SELECT) icon, then press the MENU button. The OSD displays: 1 2 DIGITAL • 1 2 INPUT Press the UP or DOWN button to select DIGITAL INPUT. NOTE: The POWER button is used for switching the LCD monitor on and off, it does not disconnect the device from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket.
Installation Using Your LCD Monitor In order to ensure a healthy and relaxed body position when using the monitor at visual display workstations, you are able to adjust the monitor’s angle or height of the stand. 1 The angle of the LCD monitor may be adjusted approximately 40 degrees. -5o 2 35o Use one hand to turn right the monitor. The pivot rotation of the LCD monitor may be adjusted approximately 90 degrees.
Installation NOTE: If you find that your display card driver does not offer this feature, you can purchase aftermarket rotation software from manufacturers such as Portrait Displays. This monitor manufacturer provides no warranty with respect to the use of aftermarket display software. Xerox© LCD Monitor User’s Manual 17 ENGLISH To access the SETTINGS dialog box, go to START>SETTINGS>CONTROL PANEL>DISPLAY. Inside the DISPLAY PROPERTIES window, go to the SETTINGS Tab.
Installation 3 The height of the LCD monitor’s stand may be adjusted approximately 12cm. Be sure to follow the sequence described below. Step1. First, release the LCD monitor’s stand lock. Use one hand to push the upper end of stand down, while using the other hand to press the stand’s lock button to unlock. Stand Lock Button Step2. With the stand lock released, move the stand post up or down slowly to the desired position.
Installation ENGLISH Step3. Next, adjust the height of the stand’s post Use one hand to press down the upper end of stand to lower the height of the stand’s post, you should feel some resistance to this motion. NOTE: When the stand’s post is moved into lock position, please repeat Step 1 to release. 4 Use one hand to change the monitor’s swivel angle . The swivel angle of the LCD monitor may be adjusted approximately 60 degrees.
Installation Installing the Wall Mount (optional) to Your LCD Monitor If you wish to lock the LCD monitor on a wall, carefully follow the instructions below. 1 Remove the screws on the back of the stand. 2 Affix the VESA mount to the back of the LCD monitor using the four screws provided in the wall-mount kit. NOTE: For instructions on wall-mount installation, please refer to the installation guide provided by the wall-mount kit vendor.
OSD Menu ENGLISH 3 OSD Menu Using the OSD Menu To create the best picture, your XAP series has been preset at the factory with the Preset Mode Timing shown on page 25. The OSD (On Screen Display) Menu allows the user to adjust various settings and options by following the steps below. 1 Press the MENU button to display the OSD. The OSD main menu provides an overview of the selection of controls available. BRIGHTNESS 2 3 4 5 Press the UP or DOWN button to highlight the desired icon.
OSD Menu The OSD Options The OSD menu includes the following options: BRIGHTNESS O BRIGHTNESS Controls the overall brightness. CONTRAST Controls the difference between the brightest and darkest regions of the picture. H. POSITION Adjusts the position of the picture left and right in the window. V. POSITION Adjusts the position of the picture up and down in the window. H.SIZE Adjusts the width of the picture. PHASE Adjusts signal phase, which can improve focus clarity and image stability.
OSD Menu ENGLISH COLOR Allows selection of the general color tint: Select User Mode, WARM, or COOL. RED COOL WARM Select User Mode Allows the user to adjust red, green and blue color component levels independently. COOL Inclines colors toward the blue end of the spectrum. Fixes the red, green and blue component levels at factory settings; they cannot be independently adjusted. WARM Inclines colors toward the red end of the spectrum.
OSD Menu OSD Changes the position of the OSD. H. POSITION Moves the OSD left and right in the window. V. POSITION Moves the OSD up and down in the window. EXIT Exits the OSD menu. EXIT Exits the OSD.
Technical Information ENGLISH 4 Technical Information Preset Mode Timing Chart The screen image has been optimized during manufacture for the display modes listed below. Video signal: (IBM PC/AT) Horizontal Frequency(kHz) Vertical Frequency(Hz) 720 x 400 31.47 70.00 640 x 480 31.47 60.00 37.86 72.80 37.50 75.00 35.16 56.25 37.88 60.30 48.08 72.20 46.87 75.00 48.36 60.00 56.48 70.10 60.02 75.00 63.98 60 79.
Technical Information DVI Connector PIN Assignment 1 8 9 16 17 24 C1 C2 C3 C4 PIN DESCRIPTION PIN 1 TMDS Data 2- 15 GND 2 TMDS Data 2+ 16 Hot Plug Detect 3 TMDS Data 2/4 shield 17 TMDS Data 0- 18 TMDS Data 0+ 19 TMDS Data 0/5 shield 4 5 6 DDC Clock 20 7 DDC Data 21 8 Analog Vertical Sync 22 Clock shield 9 TMDS Data 1- 23 Clock + 10 TMDS Data 1+ 24 Clock - 11 TMDS Data 1/3 shield C1 Analog red C2 Analog green C3 Analog blue C4 Analog 12 13 14 26 DESCR
Technical Information 1 6 5 10 11 15 PIN ENGLISH D-SUB Connector PIN Assignment DESCRIPTION 1 Red 2 Green 3 Blue 4 Ground 5 Self Test 6 Red Ground 7 Green Ground 8 Blue Ground 9 5 VDC 10 Ground 11 Ground 12 SDA (FOR DDC) 13 H. Sync 14 V.
Technical Information Plug and Play This monitor conforms to the VESA DDC (Display Data Channel) standard, which means that when it is used with a DDC compatible video card, the monitor is easier to set up. With VESA DDC 1/2B, when the monitor is turned on, it will automatically notify a windows 9X/2000/XP host computer of its scanning frequencies, capabilities and characteristics. Windows 9X/2000/XP will automatically recognize the presence of the monitor and select the appropriate display resolution.
Technical Information ENGLISH Troubleshooting Before consulting service personnel, check the following chart for a possible cause and solution to the trouble you are experiencing. Monitor will not turn on • Make sure the power cord is plugged in. No picture • Make sure the power cord is plugged in. • Check the signal cable connecting the LCD monitor and the computer (refer to page 12-14). • Press the POWER button on the front panel of the monitor.
Technical Information Specifications MODEL XAP-172i XXAP-192i Panel Size 17’ TFT LCD 19” TFT LCD Brightness 300 300 Contrast Ratio 500:1 500:1 Dot Pitch 0.264mm x 0.264mm 0.294mm x 0.294mm Max.
Technical Information ENGLISH Authorized Service Centers U.S.A. CALIFORNIA: AUTHORIZED SERVICE CENTER 7373 HUNT AVENUE GARDEN GROVE, CA 92841 (714) 799-3899 (800) 469-1175 (714) 379-6290 Fax Hours: 8AM ~ 6PM - Pacific Standard Time TEXAS: AUTHORIZED SERVICE CENTER 10849 KINGHURST SUITE # 120 HOUSTON, TX 77099 (281) 530-4100 (281) 530-4104 Fax Hours: 8AM ~ 6PM - Central Time EUROPE AUTHORIZED SERVICE CENTER CONTACTS: XOAL BVBA RAKETSRAAT 100 B-1130 BRUSSEL BELGIUM E-EMAIL: rma@proview-repair.com http://www.
