User’s Guide XM7-19w LCD Monitor
©2006 by Xerox Corporation. All rights reserved. Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as icons, screen displays, looks, etc. XEROX® and all Xerox product names mentioned in this publication are trademarks of XEROX CORPORATION.
Table of Contents CE Marking Declaration Of Conformity .................................................4 Federal Communications Commission (FCC) Statement ....................5 Important Safety Instructions.................................................................6 1 Introduction Features ........................................................................................................9 Package Contents .......................................................................................
ENGLISH Recycling Place EUROPE When disposing of Xerox Branded Monitors in Europe, please contact one of the following three locations to make arrangements for recycling. Proview International (UK) Limited 30 The Avenue, Watford, Hertfordshire WD17 4AE United Kingdom Timothy Lo Tel: +44 1923-248-111 Fax: +44 1923-248-222 Email: tim.lo@proview.co.uk PGL Europe B.V.
FCC/CE CE Marking Declaration Of Conformity This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/EEC “Low Voltage Directive” as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
FCC/CE ENGLISH Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits of a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Important Safety Instructions Important Safety Instructions To prevent any injuries, the following safety precautions should be observed in the installation, use, servicing and maintenance of this equipment. Before operating this equipment, please read this manual completely, and keep it nearby for future reference. Warnings • Do not place the equipment on any uneven or unstable carts, stands, tables, shelves etc.
Important Safety Instructions ENGLISH • Do not touch the power cord and antenna cable during lightning. • Remove the plug from the wall outlet if the equipment will not be used for a long period of time. • Do not place, use or handle this equipment near water. • Never expose the equipment to liquid, rain, or moisture. Seek qualified service if any of the above is spilled into the equipment. • Do not attempt to service the equipment yourself.
Important Safety Instructions • If any of the following conditions occur, unplug the power cord from the outlet and request service from qualified personnel. a. The power cord or plug is damaged. b. Liquid is spilled into the product . c. An object falls onto or into the product. d. The product has been dropped or damaged. e. The product’s display is abnormal.
Introduction ENGLISH 1 Introduction Features • Rapid Video Response Fast action media such as gaming, DVD and video conferencing will playback smoothly thanks to the rapid video response time of the LCD panel. • High Contrast Ratio Vibrant colors, and dark black levels will improve your graphics, photos, or presentations making them life-like and realistic. High contrast levels further define picture detail providing rich saturated images.
Introduction Package Contents Make sure the following items are in the box. If any items are missing, please return this product to the original place of purchase. LCD Monitor D-SUB Cable AUDIO Cable ������������ ������������ ������� AC Power Cord ������� ����������� ����������� Quick Guide Warranty Card CD-ROM (Driver/Manual) CAUTION: Be sure to save original box and all packing material for future transport of monitor.
Introduction ENGLISH Front View and Controls 1 2 4 3 5 1 MENU Press once to display the OSD (On Screen Display). And press to activate the items you highlight . 2 DOWN/UP In OSD mode, press the DOWN/UP buttons to move the selection highlight to the next menu item counterclockwise or clockwise, respectively. Adjusts the volume up and down. 3 AUTO Press to automatically adjust the display settings to optimize performance based on the D-SUB signal.
Installation 2 Installation Refer to the owner’s manual of the computer for connections. In the process of connecting external equipment, do not connect any AC power cords to wall outlets until all other connections are completed. Connecting Your LCD Monitor to a Computer Method 1 : Analog (D-SUB) Connection 1 2 3 4 5 12 Turn off the computer and unplug the power cord. Connect the signal cable to the D-SUB port on the back of the computer.
Installation ENGLISH D-SUB ONLY 2 D-SUB/1 DVI 3 Connect to the Line-in port 2 Connect to the D-SUB port 4 Connect to power source NOTE: Your LCD monitor may come with D-SUB connector only or 2 D-SUB/1 DVI connectors. NOTE: Unplug the monitor before installation to avoid electric shock or damage. NOTE: The button is used for switching the LCD monitor on and off, it does not disconnect the device from the main voltage.
Installation Method 2: Digital (DVI) Connection 1 2 3 4 5 6 Turn off the computer and unplug the power cord. Connect the DVI signal cable (not included) to the DVI port on the back of the computer. Connect the audio cable to the line-in port on the back of the computer. Connect the power cord to the LCD monitor and wall outlet. Press the button, located on the bottom side of the main unit to turn the monitor on, then turn the computer on.
Installation ENGLISH HOW TO GET SUPPORT FOR YOUR WIDE SCREEN? The wide-screen display enables you to view your content in a brand new way. The next generation of computing environments and game consoles are planning to support widescreen resolutions. ■ Multitask - view applications side by side and reduce toggling between them. ■ Enrich - view DVD films in their native wide format for an enhanced multimedia experience. ■ Experience - enjoy gaming action at higher wide-screen resolution.
Installation Using Your LCD Monitor In order to ensure a healthy and relaxed body position when using the monitor at visual display workstations, you are able to adjust the monitor’s angle or height of the stand. 1 The angle of the LCD monitor may be adjusted approximately 40 degrees. -5o 2 35o Use one hand to turn right the monitor. The pivot rotation of the LCD monitor may be adjusted approximately 90 degrees.
OSD Menu NOTE: If you find that your display card driver does not offer this feature, you can purchase aftermarket rotation software from manufacturers such as Portrait Displays®. This monitor manufacturer provides no warranty with respect to the use of aftermarket display software. Xerox© LCD Monitor User’s Manual 17 ENGLISH To access the SETTINGS dialog box, go to START>SETTINGS>CONTROL PANEL>DISPLAY. Inside the DISPLAY PROPERTIES window, go to the SETTINGS Tab.
OSD Menu 3 The height of the LCD monitor’s stand may be adjusted approximately 12cm. Be sure to follow the sequence described below. Step1. First, release the LCD monitor’s stand lock. Use one hand to push the upper end of stand down, while using the other hand to press the stand’s lock button to unlock. Stand Lock Button Step2. With the stand lock released, move the stand post up or down slowly to the desired position.
OSD Menu NOTE: When the stand’s post is moved into lock position, please repeat Step 1 to release. 4 Use one hand to change the monitor’s swivel angle . The swivel angle of the LCD monitor may be adjusted approximately 60 degrees. 30o 30o Xerox© LCD Monitor User’s Manual 19 ENGLISH Step3. Next, adjust the height of the stand’s post Use one hand to press down the upper end of stand to lower the height of the stand’s post, you should feel some resistance to this motion.
OSD Menu 3 OSD Menu Using the OSD Menu To create the best picture, your XM7-19w has been preset at the factory with the Preset Mode Timing shown on page 27. The OSD (On Screen Display) Menu allows the user to adjust various settings and options by following the steps below. 1 Press the MENU button to display the OSD. The OSD main menu provides an overview of the selection of controls available.
OSD Menu ENGLISH The OSD Options The main menu includes the following options: picture advanced audio options utilities reset exit auto adjust brightness contrast h position v position phase clock exit to select picture Adjusts picture settings such as brightness, contrast. advanced Allows selection of the general color tint: CUSTOM COLOR, WARM, or COOL. audio Allows selection of the sound options and effects. options Adjusts OSD settings such as H/V position, H size and phase.
OSD Menu The picture Menu 1 The picture menu provides access to the following menus: picture advanced audio options utilities reset exit auto adjust brightness contrast h position v position phase clock exit to select 2 The picture menu includes the following options: ON DESCRIPTION auto adjust Automatically adjust the display settings to optimize performance based on the D-SUB signal. brightness Controls the overall brightness.
OSD Menu 1 The advanced menu provides access to the following menus: picture advanced audio options utilities reset exit sharpness color cool user red user green user blue exit 1 2 3 4 5 natural warm user 2 The advanced menu includes the following options: ON DESCRIPTION sharpness Increase this setting to see crisp edges in the picture; decrease for soft edges. color Allows selection of the general color tint: user, natural, warm, or cool. cool Inclines colors toward the blue end of the spectrum.
OSD Menu The audio Menu 1 The audio menu provides access to the following menus: picture advanced audio options utilities reset exit volume mute exit on off 2 The audio menu includes the following options: ON DESCRIPTION volume Adjusts the speakers volume up and down. mute Mutes and restores the monitor speakers sound. exit Exits the audio menu.
OSD Menu ENGLISH The options Menu 1 The options menu provides access to the following menus: picture advanced audio options utilities reset exit osd h position osd v position exit 2 The options menu includes the following options: ON DESCRIPTION osd h. position Moves the OSD left and right in the window. osd v. position Moves the OSD up and down in the window. exit Exits the OSD menu.
OSD Menu The utilities Menu 1 The utilities menu provides access to the following menus: picture advanced audio options utilities reset exit osd timeout osd background language exit 15 seconds opaque translucent 2 The utilities menu includes the following options: ON DESCRIPTION osd timeout Allows selection of the display time of the on-screen menu. osd background Controls the translucence of the on-screen menu’s background. languages Allows selection of the languages used on all the on-screen menus.
Technical Information ENGLISH 4 Technical Information Preset Mode Timing Chart The screen image has been optimized during manufacture for the display modes listed below. Video signal: (IBM PC/AT) Horizontal Frequency(kHz) Vertical Frequency(Hz) 720 x 400 31.47 70.00 640 x 480 31.47 60.00 37.86 72.80 37.50 75.00 35.16 56.25 37.88 60.30 48.08 72.20 46.87 75.00 48.36 60.00 56.48 70.10 60.02 75.00 63.
Technical Information DVI Connector PIN Assignment 1 8 9 16 17 24 C1 C2 C3 C4 PIN DESCRIPTION PIN 1 TMDS Data 2- 15 GND 2 TMDS Data 2+ 16 Hot Plug Detect 3 TMDS Data 2/4 shield 17 TMDS Data 0- 18 TMDS Data 0+ 19 TMDS Data 0/5 shield 4 5 6 DDC Clock 20 7 DDC Data 21 8 Analog Vertical Sync 22 Clock shield 9 TMDS Data 1- 23 Clock + 10 TMDS Data 1+ 24 Clock - 11 TMDS Data 1/3 shield C1 Analog red C2 Analog green C3 Analog blue C4 Analog 12 13 14 28 DESCR
Technical Information 1 6 5 10 11 15 PIN ENGLISH D-SUB Connector PIN Assignment DESCRIPTION 1 Red 2 Green 3 Blue 4 Ground 5 Self Test 6 Red Ground 7 Green Ground 8 Blue Ground 9 5 VDC 10 Ground 11 Ground 12 SDA (FOR DDC) 13 H. Sync 14 V.
Technical Information Plug and Play This monitor conforms to the VESA DDC (Display Data Channel) standard, which means that when it is used with a DDC compatible video card, the monitor is easier to set up. With VESA DDC 1/2B, when the monitor is turned on, it will automatically notify a windows 9X/2000/XP host computer of its scanning frequencies, capabilities and characteristics. Windows 9X/2000/XP will automatically recognize the presence of the monitor and select the appropriate display resolution.
Technical Information ENGLISH Troubleshooting Before consulting service personnel, check the following chart for a possible cause and solution to the trouble you are experiencing. Monitor will not turn on • Make sure the power cord is plugged in. No picture • Make sure the power cord is plugged in. • Check the signal cable connecting the LCD monitor and the computer (refer to page 12-15). • Press the button on the front panel of the monitor.
Technical Information Specifications MODEL LCD Panel XM7-19w Panel Size 19”w TFT LCD Brightness 300 Contrast Ratio 700:1 Dot Pitch 0.285mm x 0.285mm Speakers Built-In Max. Resolution 1440x900 Input Connector D-SUB x 2/ DVI x 1/PC AUDIO or D-SUB only Power Source AC100-240V, 50-60Hz Power Consumption 60W Dimension 485x367x202 mm Changes are periodically made to this specifications. Current specifications may also be obtained via the internet, www.xerox-displays.com or www.xerox-displays.
Technical Information ENGLISH Authorized Service Centers U.S.A. CALIFORNIA: AUTHORIZED SERVICE CENTER 7373 HUNT AVENUE GARDEN GROVE, CA 92841 (714) 799-3899 (800) 469-1175 (714) 379-6290 Fax Hours: 8AM ~ 6PM - Pacific Standard Time TEXAS: AUTHORIZED SERVICE CENTER 10849 KINGHURST SUITE # 120 HOUSTON, TX 77099 (281) 530-4100 (281) 530-4104 Fax Hours: 8AM ~ 6PM - Central Time EUROPE AUTHORIZED SERVICE CENTER CONTACTS: XOAL BVBA RAKETSRAAT 100 B-1130 BRUSSEL BELGIUM E-EMAIL: rma@proview-repair.com http://www.
