XEROX XM9 User's Guide 290.00 mm 145.00 mm User ' s Guide XM9-23w 210.00 mm LCD Monitor XA7-17i XA7-19i PANTONE Process Black CV PANTONE Red 032 CV 1.
©2005 by Xerox Corporation. All rights reserved. Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as icons, screen displays, looks, etc. XEROX® and all Xerox product names mentioned in this publication are trademarks of XEROX CORPORATION.
Table of Contents TCO’03 .....................................................................................................3 CE Marking Declaration Of Conformity .................................................5 Federal Communications Commission (FCC) Statement ....................6 Important Safety Instructions.................................................................7 1 Introduction Features ......................................................................................................
TCO ENGLISH Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment.
RECYCLING PLACE Recycling Place EUROPE When disposing of Proview products in Europe, please contact one of the following three locations to make arrangements for recycling. Proview International (UK) Limited 30 The Avenue, Watford, Hertfordshire WD17 4AE United Kingdom Timothy Lo Tel: +44 1923-248-111 Fax: +44 1923-248-222 Email: tim.lo@proview.co.uk PGL Europe B.V.
FCC/CE ENGLISH CE Marking Declaration Of Conformity This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/EEC “Low Voltage Directive” as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
FCC/CE Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits of a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Important Safety Instructions ENGLISH Important Safety Instructions To prevent any injuries, the following safety precautions should be observed in the installation, use, servicing and maintenance of this equipment. Before operating this equipment, please read this manual completely, and keep it nearby for future reference. Warnings • Do not place the equipment on any uneven or unstable carts, stands, tables, shelves etc.
Important Safety Instructions • Do not touch the power cord and antenna cable during lightning. • Remove the plug from the wall outlet if the equipment will not be used for a long period of time. • Do not place, use or handle this equipment near water. • Never expose the equipment to liquid, rain, or moisture. Seek qualified service if any of the above is spilled into the equipment. • Do not attempt to service the equipment yourself.
Important Safety Instructions ENGLISH • If any of the following conditions occur, unplug the power cord from the outlet and request service from qualified personnel. a. The power cord or plug is damaged. b. Liquid is spilled into the product . c. An object falls onto or into the product. d. The product has been dropped or damaged. e. The product’s display is abnormal.
on Introduction 1 Introduction Features xTraSharp Wider View Angle xTraMove • Rapid Video Response Fast action media such as gaming, DVD and video Xtouch buttons xStand DVI conferencing will playback smoothly thanks to the rapid video 8ms response time of the LCD panel. • Extremely High Resolution Expand your view with this 23” 1920x1200 native resolution xTraSharp xTraMove xTraColor xTraLive xShield DTTV Anti-Reflection Wider View Angle wide-screen LCD.
Introduction Make sure all of the following contents are included in the box. If any items are missing, please return this product to the original place of purchase. LCD Monitor CD-ROM (Driver/User Guide) D-SUB Cable Power Cord* AC-DC Adapter Quick Guide Warranty Card DVI Cable Audio Cable * Power cord specification : H05 VV-F 3G 0.75mm2 Optional Parts Optional parts as below are available for the XM9-23w series.
Introduction Front View and Controls 1 Press the POWER button, located on the bottom side of the main unit. 2 Press the MENU button, located on the bottom side of the main unit to display on-screen menu.
Introduction ENGLISH 1 8 2 7 3 6 4 5 1 ◄► In OSD mode, press the ◄► buttons to change the value of the selected item. Adjusts the volume up and down. 2 ▲▼ In OSD mode, press the ▲▼ buttons to move the selection highlight to the next menu item. 3 LED The LED light indicates when the LCD monitor is activated (blue light indicates power on and amber flash indicates power saving). 4 Turns the LCD monitor on and off.
Installation 2 Installation Refer to the owner’s manual of the computer for connections. In the process of connecting external equipment, do not connect any AC power cords to wall outlets until all other connections are completed. Connecting Your LCD Monitor to a Computer Method 1: Analog (D-SUB) Connection 1 2 3 Turn off the computer and unplug the power cable. Connect the D-SUB signal cable to the D-SUB port on the back of the computer.
Installation 5 6 If you would like to listen to PC audio with a headphone, connect the audio out port to the headphone. Connect the DC plug of the AC-DC adapter to the DC 24V port at the rear of the monitor. Connect the power cord to the AC-DC adapter and wall outlet. Press the button, located on the bottom side of the main unit to turn the monitor on, then turn the computer on. If the monitor displays an image, the monitor is successfully installed. If no image is displayed, check all connections.
Installation Method 2: Digital (DVI) Connection 1 2 3 4 5 6 16 Turn off the computer and unplug the power cable. Connect the signal cable (DVI-D) to the DVI port on the back of the computer. Connect the audio cable to the line-in port on the back of the computer. If you would like to listen to PC audio with a headphone, connect the audio out port to the headphone. Connect the DC plug of the AC-DC adapter to the DC 24V port at the rear of the monitor.
Installation ENGLISH 5 Connect to power source 2 Connect to the DVI port 3 Connect to the Line-in port 4 Connect to the Headphone Xerox© LCD Monitor User’s Manual 17
Installation Using Your LCD Monitor In order to ensure a healthy and relaxed body position when using the monitor at visual display workstations, you are able to adjust the monitor’s angle of the stand. The angle of the LCD monitor may be adjusted approximately 35 degrees. -5o 30o NOTE: Press and hold the button for approximately 2 seconds to turn the LCD monitor off. NOTE: The button is used for switching the LCD monitor on and off, it does not disconnect the device from the main voltage.
Installation ENGLISH Installing the Speaker(optional) to Your LCD Monitor Install Follow the instructions below to install the optional speakers. 1 Attach the speaker onto both sides of the LCD monitor as shown. Speaker hooks Speaker plug in Speaker hooks Speaker plug in 2 Hold the optional speaker and place it on the two hooks and speaker plug on the unit as shown.
Installation 3 Once the hooks are matched with the LCD monitor unit, pull the speaker down to complete the attachment. Remove Push the speaker unplug button of the speaker in the direction of the arrows and pull away from the LCD monitor unit.
Installation If you with to lock the LCD monitor on a wall, carefully follow the instructions below. 1 Remove the screws on the back of the stand. 2 Use the screws to fix the VESA mount (two type:75x75mm, 100x100m) on the rear of the display monitor. Be sure the screws are firmly fixed in place. 3 Affix the VESA mount to the back of the LCD monitor using the four screws provided in the wall-mount kit.
OSD Menu 3 OSD MENU Using the OSD Menu To create the best picture, your XM9-23w series has been preset at the factory with the Preset Mode Timing shown on page 29. The OSD (On Screen Display) Menu allows the user to adjust various settings and options by following the steps below. 1 2 Press the button to display the OSD. The OSD main menu provides an overview of the selection of controls available. Press the ▲ or ▼ button to highlight the desired sub-menu icon.
OSD Menu Press the ▲ or ▼ button to select the desired adjustment item. ENGLISH 3 PICTURE SETUP CONTRAST BRIGHTNESS H-POSITION V-POSITION CLOCK PHASE COLOR TEMP ► ATO ADJUST ▲▼: MOVE 4 5 6 ◄►: SELECT MENU : EXIT Press the ◄ or ► button to change the value of the selected item. Select the icon to exit the OSD. Repeat steps 1 through 5 to make further adjustments. All changes are stored immediately.
OSD Menu The OSD Options The main menu includes the following options: ON DESCRIPTION 1 PICTURE SETUP Adjusts picture settings such as brightness, contrast. PICTURE SETUP MAIN MENU CONTRAST BRIGHTNESS H-POSITION V-POSITION CLOCK PHASE COLOR TEMP ► ATO ADJUST ▲▼: MOVE 2 ◄►: SELECT MENU : EXIT SOUND SETUP Allows selection of the sound options and effects.
OSD Menu 1 The PICTURE SETUP Menu provides access to the following menus: PICTURE SETUP MAIN MENU CONTRAST BRIGHTNESS H-POSITION V-POSITION CLOCK PHASE COLOR TEMP ► ATO ADJUST ▲▼: MOVE ◄►: SELECT MENU : EXIT 2 The PICTURE SETUP menu includes the following options: ON DESCRIPTION CONTRAST Controls the difference between the brightest and darkest regions of the picture. BRIGHTNESS Controls the overall brightness. H. POSITION Adjusts the position of the picture left and right in the window. V.
OSD Menu COLOR TEMP Allows selection of the general color tint: NATURAL, WARM, COOL, or USER. COLOR TENP MAIN MENU COLOR ◄ OFF ► USER - R USER - G USER - B ▲▼: MOVE ◄►: SELECT MENU : EXIT NATURAL Inclines colors toward the natural end of the spectrum. Fixes the red, green and blue component levels at factory settings; they cannot be independently adjusted. COOL Inclines colors toward the blue end of the spectrum.
OSD Menu 1 The SOUND SETUP Menu provides access to the following menus: SOUND SETUP MAIN MENU BASS TREBLE BALANCE MUTE ▲▼: MOVE ◄ ◄►: SELECT OFF ► MENU : EXIT 2 The SOUND SETUP menu includes the following options: BASS Controls the relative intensity of lower-pitched sounds. TREBLE Controls the relative intensity of higher-pitched sounds. BALANCE Adjusts the relative volume of the speakers in a multiplespeaker system. MUTE Mutes and restores your monitor sound.
OSD Menu The OSD SETUP Menu 1 The OSD TIME Menu provides access to the following menus: OSD SETUP MAIN MENU LANGUAGES ◄ ENGLISH ► OSD TIMEOUT TRANSPARENCY DISPLAY ► RESET ▲▼: MOVE ◄►: SELECT MENU : EXIT 2 The OSD TIME menu includes the following options: ON DESCRIPTION LANGUAGES Allows selection of the languages used on all the on-screen menus. OSD TIMEOUT Allows selection of the display time of the on-screen menu. TRANSPARENCY Controls the translucence of the on-screen menu’s background.
Technical Information ENGLISH 4 Technical Information Preset Mode Timing Chart The screen image has been optimized during manufacture for the display modes listed below. Video signal: (IBM PC/AT) Horizontal Frequency(kHz) Vertical Frequency(Hz) 640 x 350 31.47 70.08 720 x 400 31.47 70.08 640 x 480 31.47 60.00 37.86 72.80 37.50 75.00 35.16 56.25 37.88 60.30 46.87 75.00 48.36 60.00 56.48 70.10 60.02 75.00 63.98 60 79.98 75.00 91.10 85.00 1600 x 1200 75.00 60.
Technical Information DVI Connector PIN Assignment 1 8 9 16 17 24 PIN DESCRIPTION PIN 1 TMDS Data 2- 15 GND 2 TMDS Data 2+ 16 Hot Plug Detect 3 TMDS Data 2/4 shield 17 TMDS Data 0- 18 TMDS Data 0+ 19 TMDS Data 0/5 shield 4 5 6 DESCRIPTION DDC Clock 20 7 DDC Data 21 8 Analog Vertical Sync 22 Clock shield 9 TMDS Data 1- 23 Clock + 10 TMDS Data 1+ 24 Clock - 11 TMDS Data 1/3 shield 12 13 14 30 +5V Power Xerox© LCD Monitor User’s Manual
Technical Information 1 6 5 10 11 15 PIN ENGLISH D-SUB Connector PIN Assignment DESCRIPTION 1 Red 2 Green 3 Blue 4 Ground 5 Self Test 6 Red Ground 7 Green Ground 8 Blue Ground 9 5 VDC 10 Ground 11 Ground 12 SDA (FOR DDC) 13 H. Sync 14 V.
Technical Information Plug and Play This monitor conforms to the VESA DDC (Display Data Channel) standard, which means that when it is used with a DDC compatible video card, the monitor is easier to set up. With VESA DDC 1/2B, when the monitor is turned on, it will automatically notify a windows 9X/2000/XP host computer of its scanning frequencies, capabilities and characteristics. Windows 9X/2000/XP will automatically recognize the presence of the monitor and select the appropriate display resolution.
Technical Information ENGLISH Troubleshooting Before consulting service personnel, check the following chart for a possible cause and solution to the trouble you are experiencing. Monitor will not turn on • Make sure the power cord is plugged in. No picture • Make sure the power cord is plugged in. • Check the signal cable connecting the LCD monitor and the computer (refer to page 14-17). • Press the POWER/ button on the front panel of the monitor.
Technical Information Specifications MODEL LCD Panel XM9-23w Panel Size 23” WIDE TFT LCD Brightness 250 Contrast Ratio 800:1 Dot Pitch 0.258mm x 0.258mm Max. Resolution 1920x1200 Speakers Optional Input Connector DVI-D x1/ D-SUBx1/ AUDIO IN x2/AUIDO OUT x1 Power Source AC100-240V, 50-60Hz Power Consumption 96W Dimension 542x438.8x210 mm Stand V type Changes are periodically made to this specifications. Current specifications may also be obtained via the internet, www.xerox-displays.
Technical Information ENGLISH Authorized Service Centers U.S.A. CALIFORNIA: AUTHORIZED SERVICE CENTER 7373 HUNT AVENUE GARDEN GROVE, CA 92841 (714) 799-3899 (800) 469-1175 (714) 379-6290 Fax Hours: 8AM ~ 6PM - Pacific Standard Time TEXAS: AUTHORIZED SERVICE CENTER 10849 KINGHURST SUITE # 120 HOUSTON, TX 77099 (281) 530-4100 (281) 530-4104 Fax Hours: 8AM ~ 6PM - Central Time EUROPE AUTHORIZED SERVICE CENTER CONTACTS: XOAL BVBA RAKETSRAAT 100 B-1130 BRUSSEL BELGIUM E-EMAIL: rma@proview-repair.com http://www.
