Water-proof IR Network Camera User Manual
PROVISION-ISR DI-390IPVF User Manual 1080P IR Fixed Lens IP Dome Camera For H.
Cautions Before operation, we strongly advise users to read this manual and keep it properly for using later. Please use the specified power supply to connect. Avoid from in correct operation, shock vibration, heavy pressing which can cause damage to product. Do not use corrosive detergent to clean main body of the camera. If necessary, please use soft dry cloth to wipe dirt; for hard contamination, use neutral detergent. Any cleanser for high grade furniture is applicable.
Contents 1 2 3 4 5 6 7 8 9 Introduction .................................................................................................................................................... 1 1.1 Package .................................................................................................................................................... 1 1.2 Overview ..........................................................................................................................................
C Ch haap ptteerr 11 IIn nttrro od du uccttiio on n 1Introduction This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV solutions. It adopts state of the art video processing chips. It utilizes most advanced technologies, such as video encoding and decoding technology, complies with the TCP/IP protocol, SoC, etc to ensure this system more stable and reliable. This unit consists of two parts: the IP-CAM device and central management software (short for CMS).
C Ch haap ptteerr 11 IIn nttrro od du uccttiio on n CVBS Video Cable: Connect to monitor. MIC Audio Cable: Connect to microphone. DC 12V Power Cable: DC 12V power input. LAN Network Cable: Connect to internet; PoE power supply supported.
C Ch haap ptteerr 22 IIn nssttaallllaattiio on n 2Installation 2.1Ceiling Mounting Before start, please make sure that the ceiling is strong enough to withstand 3 times the weight of the camera. Part of our products may not support to adjust focus or zoom. If you have such cameras, please skip the steps of the zoom and focus adjustment. Step 1: Loosen the lock screw to disassemble the camera from the mounting base.
C Ch haap ptteerr 22 IIn nssttaallllaattiio on n Step 6: Ajust the Zoom screw and the Focus screw with the screwdriver until you get the optimum image. 2.2CMS and IP-Tool Installation Find CMS software from CD and then double click “Setup.exe” file to pop up installation wizard. Install the software according to the prompts in the wizard. After you complete the installation, you will see the CMS and IP-Tool icon on the desktop. Please see the user manual of this software for more details.
C Ch haap ptteerr 33 IIEE C Co on nn neeccttiio on n 3IE Connection User can connect IP-CAM through LAN or WAN. Here only take IE browser (6.0) for example. The details are as follows. 3.1LAN In LAN, there are two ways to access IP-CAM:①Access through IP-Tool;② Directly Access through IE Browser. 3.1.1Access through IP-Tool Step 1: Make sure the PC and IP-Cam are connected to the LAN and the IP-Tool is installed in the PC from the CD. Step 2: Use IP-Tool to modify the network of IP-Cam.
C Ch haap ptteerr 33 IIEE C Co on nn neeccttiio on n For example, the network segment of this computer is 192.168.13.57. So, please modify the IP address, Subnet Mask, Gateway of IP-Cam which must be in the same network segment with the computer. After modifying, please input the user name and password and then click “OK” button to save the setting. Note: The default user name is: admin. The default password is: 123456. The new IP address of this device will display as follows after modification.
C Ch haap ptteerr 33 IIEE C Co on nn neeccttiio on n Input User name and password and then click “OK” button to login. Note: User also can use the modified IP address of the IP-Cam. Input the IP address in the IE browser bar and then click “Enter” to access IP-Cam. The default user name is admin. The default password is 123456. 3.1.2Directly access through IE The network service is default as shown below: IP address: 192.168.226.201 Subnet Mask: 255.255.255.0 Gateway: 192.168.226.
C Ch haap ptteerr 33 IIEE C Co on nn neeccttiio on n Step 2: Open the IE Browser and input the default address of IP-CAM and confirm. Then the IE browser will download Active X control automatically. Step 3: After downloading Active X control, the login dialog box will pop up as below: Step 4: Input user name and password in the login dialog box and click “OK” button to enter into the live interface. You can manage and setup the IP-CAM, such as change IP address etc. 3.
C Ch haap ptteerr 44 R Reem mo ottee P Prreevviieew w 4Remote Preview 4.1Remote Preview After you log in, you will see the following window. The descriptions of the icon on the remote preview interface: 1 People icon 2 Fix size 3 Zoom in 4 Zoom in 5 Zoom out 6 Full screen 7 Start record 8 Playback 9 Snap 10 Enable audio Right click mouse to appear a pull-down list as shown above: Stream: Two streams can be selected. Turn off the live: Click this item will close present live preview.
C Ch haap ptteerr 44 R Reem mo ottee P Prreevviieew w After selecting the record date, the record files will be displayed in the record file list box. User can double click a certain record file to playback or check a certain file. Then click Play button to do playback. User can do relating operation according to some buttons in the playback interface. 4.3Snap Select the picture number, and then click “Snap” icon as shown below: User can snap multiple pictures.
C Ch haap ptteerr 44 R Reem mo ottee P Prreevviieew w Click “Browse” to set saving path; Click “Save” to save pictures to HDD on the computer; Click “Printer setup” to set the printer and print the snap pictures; drag the scroll bar to view all snapped pictures.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 5Remote Configuration Functions of remote configurations include: System Configuration, Video Configuration, Alarm Configuration, Network Configuration and Advanced Configuration. You should firstly select the menu on the left, and then setup the relative parameters. When one user configures parameters of a certain device, other users can not setup this device. 5.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 2. Select “Modify Time ", user can self-define time. Choose the right "Time Zone" according to user’s location. 3. User can also enable DST and set DST mode and time. 4. User can setup time by select the “Synchronize with NTP Server”. 5. Press the "Save" button to save the settings. 5.2 Video Configuration Camera Configuration includes four submenus: Camera Configuration, Video Stream, Time Stamp and Video Mask. 5.2.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 5. Enable auto iris, the image mirror and image overturn function. 6. Press the "Save" button to save the settings. 5.2.2 Video Stream 1. Enter into "Video configuration" "Video Stream" to see a interface as shown below: 2. Select the resolution of the single frame image at the "Resolution" pull down list. 3. Select the quantity of video per second at the "Frame rate" pull down list. 4.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 5.3 Alarm Configuration Alarm configuration includes three submenus: Motion Detection Area, Motion Detection Trigger and Motion Detection Schedule. 5.3.1 Motion Detection Area 1. Enter into “Alarm configuration""Motion Detection Area" to see a interface as shown below: 2. Move the "Sensitivity" scroll bar to setup the motion trace sensitivity. 3.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n below: 2. Check "Enable alarm" check box. Then motion based alarm is activated. 3. Set alarm holding time. 4. Set alarm trigger options. Alarm Out: If selected, this would trigger the external relay output on detecting a motion based alarm. Trigger Snap: If selected, the system will snap images on an alarm and save them in SD card.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n Week schedule User could set the alarm time from Monday to Sunday for alarm everyday in one week. Note: The lengthwise means one day of a week; the rank means 24 hours of a day. Mouse clicks on the pane to set the alarm hours. Green means selected area. Blank means unselected area. 2."Add": add the schedule for a special day. 3.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 2. Input port number for IE access in the "HTTP Port" textbox. 3. Input the port number for audio & video transmission in the "Data Port" textbox. 5.4.2 Wired 1. Enter into "Network Configuration""Wired" to see a tab shown below: 2. There are two Options for setup IP: obtain an IP address auto by DHCP protocol and use the following IP address, user can choose one of options for requirements. 3.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 2. Check “transit enable”. Then save the setting. 3. Input www.upnpicp.com in IE address; download and install Active X. Then a window shows up as below: 4. Input the only device ID of the IP-CAM or user-defined name. And then input user name and password. 5.4.4 Server Configuration Enter into “Network Configuration” “Server Config”. 1. Check “Do you want IP Camera to connect Server. 2.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n Click “save” button to save the settings. 5.4.5 IP Notify 1. Enter into “Network Configuration””IP Notify” to see a tab as below. 2. If the “Enable notifying change of IP” is selected, when the IP address of the device is changed, a new IP address will be sent to the appointed mailbox automatically; If “FTP” is selected, when the IP address of the device was changed, a new IP address will be sent to FTP server. 5.4.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 2)Fill in the registration form, then click "Submit" 3)Fill in the host name you want to apply for and press "Request Domain" (for example "home") 4)If there is no problem with the domain registration you will see the following message: “Your domain was successfully created.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 1. Enter into "Network Configuration""DDNS Configuration" tab as below: Note: The steps to band a domain name for video surveillance server are as follows. Firstly, register a user name and a password to log on the website of service supplier, and then apply for a domain name online for the server. After that, users can visit the server through inputting the domain name at IE terminal. 2. Press the "Save" button to save the settings.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n Log in (3)Domain Setup Step 1: Click "Domain Management" on the left to set the domain. Domain setup Step 2: Input the domain in the textbox. For example, you set ‘IP-CAMERA’ as the domain. Step 3: Click "Submit" button, the system will pop up a dialog box to show that the domain is added successfully. Note: Time of probationary period is one month.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 5.4.7 RTSP Enter into “Network Configuration” “RTSP” interface as shown below: 1. Select “Enable RTSP server. 2. RTSP Port: Access Port of the streaming media. The default number is 554. 3. RTSP Address: The RTSP addresses are inputted in the media player. Application: This device supports VLC player. You can upload the VLC player in the related website and then select “File””Open URL” from the tool bar of the player.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n If “Show icons for networked UPnP devices” can’t display in the “Network Tasks” list box, please follow the below operation: Click “Tools”-- “Folder options” Check the “Show common tasks in folders” in the “Tasks” check box, UPnP icon will display. 5.4.9 Mail Setting Enter into “Network Configuration” “Mail Setting” interface. Please refer to below picture. 1. From Email: sender’s e-mail address 2.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n Note: If you change the static IP into PPPoE and select mailbox, there will be an e-mail sent to users’ mail box for notifying a new IP address. 5.4.10 FTP Enter into Network ConfigurationFTP interface; please refer to below picture. 1. Add: Click Add button to input FTP server’s server name, address, port number, user name, password, and upload path, click OK to confirm the setting.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n Add user: 1. Clicking "Add" button pops up "Add user" dialog box as shown below: After binding physical address to the IP-CAM, you can access the device on this PC only. If the MAC address was ““00:00:00:00:00:00” which means it can be connected to any computers. 2. Input user name in "User Name" textbox (only letters). 3. Input characters in "Password" and "Confirm Password" textbox (letters or numbers). 4.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n MAC” text box. 6. Click “OK” button to modify user’s password and binding MAC address successfully. Delete user: 1. Select the user which needs to delete in the user configuration list box. 2. Clicking “Delete” button will pop up a confirm dialog box. Then click “OK” to delete the user. Note: The default super administrator cannot be deleted.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n click “delete” button to delete that MAC address. 5. Click "save" button to save the above setting. 5.5.4 Configure Backup & Restore Enter into Advanced configurationConfigure Backup & Restore Interface. Import & Export Configuration: User can import or export the setting information from PC or to device. 1. Click “Browse” to select save path for import or export information on PC. 2.
C Ch haap ptteerr 55 R Reem mo ottee C Co on nffiig gu urraattiio on n 5.5.6 Upgrade Enter into Advanced Configuration—Upgrade interface. 1. Click “Browse” button to select the save path of the upgrade file 2. Click “Upgrade server firmware” button to start upgrading the application program 3. The device will restart automatically 4. After you successfully update the software, click “OK” button to close IE and then re-open IE to connect IP-Cam.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee 6 Mobile Surveillance This IP-CAM supports mobile surveillance by phones with Windows mobile, iPhone, Android and Blackberry OS. Please check the operation system version of mobile before use; and connect the IP-CAM to Internet. 6.1Network Configuration Access device via LAN Step 1: Connect device via wireless router. Then checkmark DHCP both in router and device to automatically acquire IP address or enter the IP address manually.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee 6.2By Phones with iPhone OS Install through Iphone. Step 1: Open App Store software as shown in the figure on the left. Step2: Search “Provision Cam” and click “Free” button as shown in the figure on the right. Step 3: Click “Install App” button as shown in the figure on the left. Step 4: Input iTunes Store password and then click “OK”. The software will be installed automatically.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee "Provision Cam" Instruction 1.Login Step 1: Choose network type. There are two network connection ways: 3G/3G +WIFI, enhanced video quality. This network supports main stream and sub stream. The real-time image will be displayed by using sub stream. 3G, normal video quality compared to the former network type. Step 2: Input server, account and password. Server: WAN IP address (or domain name) plus HTTP port of the device. For example: 210.21.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee information, device information, network information, etc. :Server list button. Click this button to add server list. :Help button. Help you know about the use of this software quickly. :CMS button. Make you preview the live image of multi-devices. :Log off button. Click this button to return to the login interface. :Screen mode button. You can choose 1,4,6,8,9,13 or 16 screen display mode. :Favorite channel display button.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee Channel indicator instruction: :Video loss : Schedule recording :Sensor alarm :Motion alarm :Others :Motion /sensor alarm based recording or manual recording 3.Server list Click button to pop up the following picture. Add device: Click “Add” button in the top right corner to pop up a dialog box as shown in the following left picture. Input the relative information of the device and click “Save” button.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee 1.Click “Screen mode” button to select channel as shown in Fig 1. 2.When there is video playing in a screen, you can switch the channel by long pressing the screen as shown in Fig 2. 3.When no video is playing in a screen, click this screen to choose channel as shown in Fig 3. 4.When the single channel is playing, you can zoom in/out the image by swiping you finger up and down as shown in Fig 4. 5.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee Fig 4 Fig 5 5.CMS Function This function makes multi-device managements and preview come true. Step 1: Click to enable CMS function. When this icon turns green, it means this function is enabled. Step 2: Click to choose channel as shown in the right picture. After you choose the channel, click “ok”, the system will display the related image automatically.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee Then click button to play. Only one favorite group can be collected. :Color means the channel or group has been collected. Grey means the channel or group isn’t collected. 7.Playback Interface Click “Playback” button to enter the playback interface. Then click “Search” button to search the file. To play the record by click this file name. 8.Image View Click button to view the captured pictures. 9.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee 6.3 By Phones with Android Software Installation Step 1: Run “Play Store” (or Google market) program. Step 2: Search “Provision Cam”. Step 3: Press “Install” button. Step 4: Install the software subject to the notes. Once the downloading is done, the software will install automatically Login Menu Step 1: Configure the network of your device and mobile phone.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee Step 3: Input the account and password of your device. The default account name is admin and the default password is 123456. Step 4: Check “Remember Server” to save PTZ the setting. When you login next time, you Snap can click Record button to select this server for quick access.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee Record Playback: Click “Playback” in the main menu interface to enter playback interface. Then choose the channel you want to playback. This will take you to see the record file. Click this file to play. Pause/Play Stop Forward Backward Server List: In the main menu interface, click “Server list” to see the above picture on the left hand. Add Server: Click button to pop up a window as shown in the above picture on the right hand.
C Ch haap ptteerr 66 M Mo ob biillee SSu urrvveeiillllaan nccee Favorite Channel: Check the favorite channels and click “Save” button to save these channels. Then go into live interface and click button to play these favorite channels. Storage: Setup the relevant parameters of mobile video. Information View: view the DVR/NVR basic information as shown in the picture on the right.
C Ch haap ptteerr 77 IIP P--TTo oo oll 7 IP-Tool Updating through IP-Tool Note: Do not cut off power supply and internet when updating. If the device is unable to start because of the failure of upgrade, it needs to retrofit. Acquire the IP-Tool from the supplier and then double click the IP-Tool icon to run this software. Then the device can be searched; if the device can’t be searched, please check whether the PC and the device connect to the network or not.
C Ch haap ptteerr 77 IIP P--TTo oo oll Modify IP address and click OK button to exit the dialog box. After that, IP-Tool will display the new IP address. Upgrade Software Select the device; right click “Update software”. Click “Update” to start upgrading,the progress bar will display as below. When upgrading, please do not disconnect PC and the device and make sure the power is on.
C Ch haap ptteerr 77 IIP P--TTo oo oll Input the relevant information and click “Browse” button to choose your update file. After that, click “Update Kernel” button to start updating. When upgrading, do not disconnect PC to device and make sure the power is on. The update progress bar will display as below: After finishing upgrading, a message box will pop up. After a while, the device will restart automatically.
C Ch haap ptteerr 88 Q Q& &A A 8Q & A 1. Q: How to find my password if I forget it? A:Use the IP-Tool. Run the IP-Tool and right click the camera information to choose “Set Factory Attribute”. Default IP: 192.168.226.201. User name: admin Password: 123456 2. Q:Fail to connect devices through IE browser, why? A: Network doesn’t connect well. Please check the connection and make sure it connected well. B: IP is not available. Reset the valid IP.
C Ch haap ptteerr 88 Q Q& &A A Fig 4-1 Fig 4-2 ④ then click ok to finish setup. b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them. 5. Q:No sound can be heard, why? A:Without connect audio input device. Please connect and try again. B: Without enable audio function at the corresponding channel. Please check AUDIO item to enable this function. 6. Q:Why doesn’t the device connect to wireless? A: Check the statues of wireless router.
C Ch haap ptteerr 99 SSp peecciiffiiccaattiio on n 9 Specification Camera Video Camera Audio Specifications Image Sensor Effective Pixels Electronic Shutter Day & Night Min.
C Ch haap ptteerr 99 SSp peecciiffiiccaattiio on n Notes: IP-CAMERA User Manual - 49
C Ch haap ptteerr 99 SSp peecciiffiiccaattiio on n IP-CAMERA User Manual - 50